Bosch EPS 708 Original Instructions Manual page 39

3.2 Requirements
!
The EPS 708 may not be operated unsupervised. It
may only be used by trained and specially instructed
personnel. Apprentices or personnel undergoing
training, induction or instruction may only use
the product under the continual supervision of
an experienced person. All work on electrical and
hydraulic equipment may only be performed by
persons with sufficient knowledge and experience
of electrical and hydraulic systems.
R
If an external cooling water supply is used, the client
must provide a pressure reducer (set to ≤ 450 kPa),
a safety filter and a shutoff valve. A coolant flow
rate of min. 14 l/min. must be ensured, in order to
provide sufficient cooling. The differential pressure
in the EPS 708 can be up to 200 kPa with a flow of
14 l/min.
R
The temperature of the cooling water may reach
max. 17 °C; if the temperature is higher the client
must provide an appropriate cooling device.
R
The cooling water must be discharged into the
waste water pipe via an oil separator without shutoff
device.
R
To ensure adequate ventilation for the EPS 708,
a gap of at least 70 centimeters must be left
between the back and sides of the unit and the wall
for EPS 708 models without internal chiller. If the
EPS 708 has a chiller, the distance between the
right-hand side of the device and the wall must be at
least 1 meter. To prevent overheating, the air grill on
the back of the EPS 708 must not be covered.
R
We recommend that the client installs an extractor
above the EPS 708. Note the opening height of the
hood in this case.
R
The client must provide a 35 A preliminary fuse.
R
Only perform tests using the test sequences of the
TestData CD (from 2011/1).
R
The client must ensure adequate noise protection.
R
Training programs on the testing of diesel
components are available at the Robert Bosch Test
Equipment training center.
Robert Bosch GmbH
Product description | EPS 708 | 39
3.3 Scope of delivery
Designation
EPS 708 (400 V or 200 V;
with/without chiller)
1)
Monitor with
mount
Mouse
PC
Pressure hose ID8 x 1000 mm (2x)
Hose connection (4x)
Pressure hose ID10 x 1000 mm (2x)
Hose connection (4x)
Hose clamp (8x)
Hoses (6x) for
CRI/CRI Piezo return to valve block (1 to 6)
Inlet filters (6x) for CRI/CRI Piezo injected fuel
quantity to valve block (A to F)
Drive coupling
USB connecting cable (1,8 m)
X24 connecting cable (to common rail pump)
Adapter cable (X27 to CRI/CRI Piezo trigger
electronics)
EP software CD
TestData CD
Recovery DVD ROM (PC software package)
T-bar
Double bit key
Square box wrench
Operating instructions
depending on the variant
1)
3.4 Special accessories
Designation
Set of accessories CP1, CP3.X
Set of accessories CP4
Supplementary equipment set CRI 846H
Set of accessories for non-Bosch common rail
pumps
Drive coupling (for CB18 and third-party pumps) 1 686 401 026
Lubricating oil supply supplementary
equipment set
CRI/CRIN 848H supplementary equipment set
T-bar
Upgrade kit for non-Bosch common rail pumps
CRI (Delphi/Denso) supplementary equipment set
CP3.4 drive flange (MAN)
High-pressure hose parts set
NRS-CP3.4 (MAN) supplementary equipment set 1 687 001 619
Adapter (connection to 180 MPa rail)
Adapter (pressure calibration)
Connection device return
for NKW Common Rail injectors
Printer
Keyboard (depending on country)
en
Order number
–
–
1 687 023 540
1 687 023 607
–
–
1 683 386 130
–
1 683 386 131
1 681 314 078
1 680 712 327
to
1 680 712 332
1 687 434 067
1 686 401 024
1 684 465 564
1 684 463 946
1 684 463 698
1 687 000 956
1 687 370 270
–
1 683 000 000
–
–
1 689 978 559
1 689 979 860
1 689 989 067
1 689 989 190
Order number
1 687 010 346
1 687 010 390
1 687 002 846
1 687 010 183
1 687 001 931
1 687 001 934
1 683 105 083
1 687 010 184
1 687 010 186
1 685 702 092
1 687 016 064
1 681 032 094
1 681 032 095
1 687 016 080
1 687 001 850
–
|
1 689 989 067 2017-12-08