Kw Ui Module Interface Overview - Siemens 6SN1123-1AA00-0DA2 Configuration Manual

6 Infeed Modules
6.2 Interface overview
6.2.2

5 kW UI module interface overview

Table 6-2 Interface overview, 5 kW UI modules
Term. Desig-
No. nation
U1 X1 Line supply connection
V1
W1
PE – Protective conductor
X131 Electronics M
X351 Equipment bus
Grounding bar
P600 DC link
M600
M500 X181 DC link power supply
P500 X181 DC link power supply
1U1 X181 Output L1
2U1 X181 Input L1
1V1 X181 Output L2
2V1 X181 Input L2
1W1 X181 Output L3
2W1 X181 Input L3
5.3 X121A
Relay contact
5.2 X121A
Group signal
5.1 X121A 2
I t/motor temperature
nc X121A
74 X121B
Relay signal
73.2 X121B
Ready/
73.1 X121B
fault
72 X121B
2)
63 X141AX Pulse enable
2)4)
9 141A FR+
2)4)
9 X141A FR+
2)
64 X141A Drive enable
5)
R X141A RESET
19 X141A FR–, reference ground enable
voltage
1) I = input; O = output; NC = NC contact; NO = NO contact
2) Term. 19 is the reference ground (connected through 10 kW to the general reference ground X131 inside the module)
Terminal 15 must not be connected to PE, to terminal 19 or to external voltage sources
Terminal 19 can be connected to X131.
The terminal may be used exclusively for enabling the associated drive group.
3) The grounding clip is used to ground the DC link M busbar through 100 kΩ (must be closed;
the grounding clip must be opened if the system is subject to a high–voltage test).
4) max. current load of terminal 9 – terminal 19  1 A
Notice: For the 5 kW, there are no terminals 7, 45, 44 and 10.
5) RESET = resets the fault memory, edge–triggered for the complete drive group
(terminal "R" ! Term. 19 = RESET)
only use copper cables dimensioned for an operating temperature w 60°C.
:
6) For UL certification
7) In accordance with EN 60204–1 (machine safety),
control transformers must be used for AC control voltages.
6-150
Type
Function
1)
I
I
I
I/O
3)
I/O
I/O
I
I
O
I
O
I
O
I
NC
NO
I
NC
I
I
NO
I
O
O
I
I
O
SIMODRIVE 611 Configuration Manual (PJU) – 02/2012 Edition
Typ. voltage/limit values
3–ph. 400 V AC
0 V
0 V
Various
–300 V
+300 V
–300 V
–300 V
+300 V
3–ph. 400 V AC
3–ph. 400 V AC
3–ph. 400 V AC
3–ph. 400 V AC
3–ph. 400 V AC
3–ph. 400 V AC
1–ph. 50 V DC/0.5 A/12 VA max
1–ph. 5 V DC/3 mA min
1–ph.250 V AC/50 V DC/2 A max
5 V DC/3 mA min
+13 V...30 V/R = 1.5 kΩ
E
+24 V
+24 V
+13 V...30 V/R = 1.5 kΩ
E
terminal 19/R = 10 kΩ
E
© Siemens AG 2012 All Rights Reserved
02.07 02.03 05.08
05.01
Max. cross–section
6)
2
4 mm
finely–stranded
without conductor end
sleeves
2
6 mm with pin–type
cable lug
M5 thread
M4 thread
34–core ribbon cable
Busbar
Conductor bar
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
7) 2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm
2
1.5 mm