Table of Contents
Advertisement
ACS510 User's Manual
5 =
3
,4
(
) – Defines digital inputs as the frequency reference source (motor potentiometer control).
DI
U
D
R
• Digital input
3 increases the speed (the
DI
• Digital input
4 decreases the speed (the
DI
• A Stop command resets the reference to zero (the
• Parameter 2205
ACCELER TIME
6 =
3
,4
– Same as above (
DI
U
D
• A Stop command does not reset the reference to zero. The reference is stored.
• When the drive restarts, the motor ramps up (at the selected acceleration rate) to the stored reference.
7 =
5
,6
– Same as above (
DI
U
D
8 =
– Defines the fieldbus as the reference source.
COMM
9 =
+
1 – Defines a fieldbus and analog input 1 (
COMM
AI
Reference Correction below.
10 =
*
1 – Defines a fieldbus and analog input 1 (
COMM
AI
Reference Correction below.
11 =
3
, 4
(
) – Same as
DI
U
D
RNC
• Changing the control source (
12 =
3
,4
(
) – Same as
DI
U
D
NC
• Changing the control source (
13 =
5
,6
(
) – Same as
DI
U
D
NC
• Changing the control source (
14 =
1+
2 – Defines an analog input 1 (
AI
AI
Analog Input Reference Correction below.
15 =
1*
2 – Defines an analog input 1 (
AI
AI
Analog Input Reference Correction below.
16 =
1-
2 – Defines an analog input 1 (
AI
AI
Analog Input Reference Correction below.
17 =
1/
2 – Defines an analog input 1 (
AI
AI
Analog Input Reference Correction below.
20 =
– Defines the control panel as the reference source. A stop command resets the reference to zero
KEYPAD(RNC)
(R stands for reset). Changing the control source (
21 =
– Defines the control panel as the reference source. A stop command dose not reset the reference
KEYPAD(NC)
to zero. The reference is stored. Changing the control source (
reference.
Analog Input Reference Correction
Parameter values 9, 10, and 14...17 use the formula in the following table.
Value
AI reference is calculated as following:
Setting
C + B
C value + (B value - 50% of reference value)
C * B
C value * (B value / 50% of reference value)
C - B
(C value + 50% of reference value) - B value
C / B
(C value * 50% of reference value) / B value
Where:
• C = Main Reference value
( =
for values 9, 10 and
COMM
=
1 for values 14...17).
AI
• B = Correcting reference
( =
1 for values 9, 10 and
AI
=
2 for values 14...17).
AI
Example:
The figure shows the reference source curves for value
settings 9, 10, and 14...17, where:
• C = 25%.
• P 4012
SETPOINT MIN
• P 4013
SETPOINT MAX
• B varies along the horizontal axis.
Supplied from China by: Guangzhou Tofee Electro Mechanical Equipment Co., Ltd
Email: info@tofee.com.cn
stands for "up").
U
stands for "down").
D
2 controls the reference signal's rate of change.
3
,4
(
)), except:
DI
U
D
R
3
,4
), except that
DI
U
D
3
,4
(
) above, except that:
DI
U
D
R
1 to
2,
2 to
EXT
EXT
EXT
3
,4
above, except that:
DI
U
D
1 to
2,
2 to
EXT
EXT
EXT
5
,6
above, except that:
DI
U
D
1 to
2,
2 to
EXT
EXT
EXT
1) and analog input 2 (
AI
1) and analog input 2 (
AI
1) and analog input 2 (
AI
1) and analog input 2 (
AI
= 0.
= 0.
stands for "reset").
R
5 and
6 are the digital inputs used.
DI
DI
1) combination as the reference source. See Analog Input
AI
1) combination as the reference source. See Analog Input
AI
1,
to
) does not copy the reference.
EXT
LOC
REM
1,
to
) does not copy the reference.
EXT
LOC
REM
1,
to
) does not copy the reference.
EXT
LOC
REM
2) combination as the reference source. See
AI
2) combination as the reference source. See
AI
2) combination as the reference source. See
AI
2) combination as the reference source. See
AI
1 to
2,
2 to
1) does not copy the reference.
EXT
EXT
EXT
EXT
1 to
2,
EXT
EXT
EXT
120
17 (/)
100
80
60
40
20
0
0
2 to
1) does not copy the
EXT
9, 14 (+)
10, 15 (*)
16 (-)
100%
Start-Up
75
B
Hide quick links:
Advertisement
Table of Contents
