Full Spectrum Laser MUSE 3D Operation Manual page 95

A. Connect the Exhaust System
B. Assemble Cool Box / Water System
1. Mount the exhaust cowling to the Muse exhaust port. 1. Using the large rubber tubing included, connect the water-out on the
Appendix A. Coolbox
Cool Box to the water-in on the Muse. Do the same from the water-in
2. Attach with 4" ducting to flange side of exhaust fan, then the second
on the Cool Box to the water-out on the Muse. Water should flow out of
ducting to the exit port of the exhaust fan.
Using Your Coolbox & Map
Coolbox into Laser Tube then back to the Cool Box. Double check these
connections.
3. Ventilate the ducting outside through a window or exhaust port.
4. If using a fume extractor, you can attach the ducting from Muse directly to
2. Using the smaller black rubber tubing, connect the air-out connection on
the Cool Box to the air assist port on the back of the Muse.
the fume extractor.
Using Your Coolbox
3. Assemble & attach exhaust fan and flange to back of the Muse.
B. Assemble Cool Box / Water System
4. Plug power cable into back of Cool Box
1. Using the large rubber tubing included, connect the water-out on the
5. Connect the black 4-prong cable from Cool Box to your Muse Laser system.
Cool Box to the water-in on the Muse. Do the same from the water-in
1.Add Distilled Water: Unscrew water cap. Fill tank with distilled water (approx. 1250 ml). Put
on the Cool Box to the water-out on the Muse. Water should flow out of This cable runs from the back of your Cool Box to the back of your Muse.
Coolbox into Laser Tube then back to the Cool Box. Double check these
cap back on and tighten.
connections. If do not have a Cool Box for your Muse please refer to instructions
2. Using the smaller black rubber tubing, connect the air-out connection on
2.Power On Coolbox: Flip the red power switch to the "On" position. Remember to always run your
the Cool Box to the air assist port on the back of the Muse.
Accessories & Upgrades
Coolbox when the laser is operating.
3. Assemble & attach exhaust fan and flange to back of the Muse.
Laser Tubes
4. Plug power cable into back of Cool Box
45W Laser Tube
Focus Lenses
5. Connect the black 4-prong cable from Cool Box to your Muse Laser system.
1.5" Lens, 2" Lens
This cable runs from the back of your Cool Box to the back of your Muse.
2.5" Lens, 5" Lens
If do not have a Cool Box for your Muse please refer to instructions
Rotary / Riser Attachments
Friction Rotor
Muse Riser
Accessories & Upgrades
Water Assist
Active Water Chiller
Laser Tubes
45W Laser Tube
Contact sales department to order
Focus Lenses
1.5" Lens, 2" Lens
2.5" Lens, 5" Lens
Rotary / Riser Attachments
Friction Rotor
Muse Riser
Water Assist
Active Water Chiller
Water In
Water Out
Contact sales department to order
Do not use
exhaust control
Fill with Distilled Water
Water In
Water Out
Cool Box / Water
Chiller / Bucket
Some users may have
Do not use
exhaust control
purchased as "industrial
chiller" Please refer to
your user manual for
setup instructions
Cool Box / Water
Chiller / Bucket
Some users may have
purchased as "industrial
chiller" Please refer to
your user manual for
setup instructions
Air Assist
Air Compressor
Extractors & Particle Filters
Small, Medium and Large Available
Exhaust Fan
Booster Fan
Filter Replacements
Small, Medium and Large Available
Air Assist
Air Compressor
• 702.802.3101 • sales@fslaser.com
Extractors & Particle Filters
Small, Medium and Large Available
Exhaust Fan
Booster Fan
Filter Replacements
Fill with Distilled Water
Small, Medium and Large Available
Water In
• 702.802.3101 • sales@fslaser.com
Water In Water Out
Technical Support is available 8am-5pm PST. Monday - Friday
D. Connect Power
C. Assemble the Air Compressor
1. The power cord plugs into a "C14" power receptacle located on the back
1. Remove the air compressor from its packaging. Gently screw on the push
side of the machine.
fitting to air compressor.
2. Follow the diagram and connect all power connections to a central power
2. Push one end of the black air inlet hose into the air compressor push fitting
bank and then plug the power strip into an appropriate wall outlet.
until it is snug.
3. Insert the other end of the black air inlet hose into the "air inlet" nozzle in
E. Connect Ethernet Cable
the back of laser cutter via the barbed air connect fitting.
1. Locate and remove the included Ethernet cable from its packaging.
2. Plug in the Ethernet cable into the Ethernet slot on your Muse.
D. Connect Power
3. Plug the other end of the Ethernet cable into your computer's Ethernet slot.
1. The power cord plugs into a "C14" power receptacle located on the back
side of the machine. 4. Connect Via Router (Recommended): Router connectivity is more
reliable than directly connecting via Ethernet and should be the primary
2. Follow the diagram and connect all power connections to a central power
way of connecting.
bank and then plug the power strip into an appropriate wall outlet.
E. Connect Ethernet Cable
1. Locate and remove the included Ethernet cable from its packaging.
2. Plug in the Ethernet cable into the Ethernet slot on your Muse.
3. Plug the other end of the Ethernet cable into your computer's Ethernet slot.
4. Connect Via Router (Recommended): Router connectivity is more
reliable than directly connecting via Ethernet and should be the primary
way of connecting.
Booster Fan
(optional)
Ducting
Booster Fan
(optional)
Fan Flange
Exhaust Fan
Water Out
Ducting
Fan Flange
Exhaust Fan
Power 110V
Power 110V
support@fslaser.com •
Particle Filter
(optional)
OR
Particle Filter
(optional)
OR
Computer
Network / Router
Ethernet cable
Computer
Network / Router
Ethernet cable
702-802-3103
Outside
Window / Door
Outside
Window / Door
Fume Extractor
U
Et
Fume Extractor
Exhaust Control
Particle Filter / Exhaust
Water Tubing
Air Tubing
Power Cords
Machine Control
Software Connection
Exhaust Control
Particle Filter / Exhaust
Water Tubing
Air Tubing
Power Cords
Machine Control
Software Connection
94
Q
F
y
i