Focus Lens Replacement - Full Spectrum Laser MUSE 3D Operation Manual

Loosen the focus head thumbscrew, slide the focus head to the uppermost p
tighten thumbscrew.
Section VIII. Hardware & Maintenance
Disconnect air hose by gently pulling it.
Focus Lens Maintenance
Air Assist Cone
Using a 1.5 hex wrench (not included), loosen the "set" screw, but do not rem
s Lens w/ case (E)
Parts
Remove the current air assist cone.
Place the fitting O-ring on the air assist fitting and attach to new air assist co
ctions:
Parts: Air Assist Cone (A) – Fitting O-Ring (B) – Air Assist Fitting (C) – Focus Billet (D) –Focus Lens w/ case (E)
oosen the focus head thumbscrew, slide the focus head to the uppermost position and
Place new air assist cone under focus lens and into slot. Tighten "set" screw
Focus Lens Replacement Instructions
ghten thumbscrew.
hex wrench. Reattach air hose.
isconnect air hose by gently pulling it.
1. Loosen the focus head thumbscrew. Slide the focus head to the uppermost position and tighten thumbscrew.
Slide the current focus lens out of the slot. This does not require tools.
2. Disconnect air hose by gently pulling it.
sing a 1.5 hex wrench (not included), loosen the "set" screw, but do not remove.
Slide new lens into slot.
3. Using a 1.5 hex wrench (not included), loosen the "set" screw, but do not remove.
emove the current air assist cone.
4. Remove the current air assist cone.
lace the fitting O-ring on the air assist fitting and attach to new air assist cone.
5. Place the fitting O-ring on the air assist fitting and attach to new air assist cone.
lace new air assist cone under focus lens and into slot. Tighten "set" screw with a 1.5
6. Place new air assist cone under focus lens and into slot. Tighten "set" screw with a 1.5hex wrench.
ex wrench. Reattach air hose.
Reattach air hose.
lide the current focus lens out of the slot. This does not require tools.
7. Slide the current focus lens out of the slot. This does not require tools.
8. Slide new lens into slot.
lide new lens into slot.
Thumbscrew
Thumbscrew
Figure 8.2
See Page 96 "Appendix B" for information regarding different types of lens FSL supplies
aintenance: The Focus Lens will need, at minimum, weekly cleaning, dependin
pes of materials used. Only use optical grade lens wipes and gently wipe the su
Figure 8.2
ean. Save the case the lens came for storage when switching to a different lens.
NOTICE
ways use the correct focus billet and air assist cone.
nance: The Focus Lens will need, at minimum, weekly cleaning, depending on usage and
f materials used. Only use optical grade lens wipes and gently wipe the surface of the lens
ens Descriptions: Save the case the lens came for storage when switching to a different lens. With any lens,
use the correct focus billet and air assist cone.
5" lens is appropriate for extra fine engravings such as fonts below 6pts.
0" lens* has a good combination of fine engraving and thin cutting for fonts betw
Descriptions:
(A) – Fitting O-Ring
Thumbscrew
A
The Focus Lens will need, at minimum, weekly cleaning, depending on usage and
D
types of materials used. Only use optical grade lens wipes and gently wipe the
surface of the lens clean. Save the case the lens came for storage when switching to
a different lens. With any lens, always use the correct focus billet and air assist cone.
Technical Support is available 8am-5pm PST. Monday - Friday
(B) – Air Assist Fitting
A
D
support@fslaser.com
(C) – Focus Billet
• 702-802-3103
(D)
E
B
C
B
90