Full Spectrum Laser MUSE 3D Operation Manual page 15

to draw fresh air through the work area.
Plug the exhaust fan power cord into the lower power plug marked
3.Ventilate Outside: Set the open end outside of a window or an installed ventilation outlet. Check your
4. Connect to Power:
system for leaks—most can be remedied with duct tape. Please be aware that the protective housing is
not designed to be airtight; the front grill is designed to allow an exhaust system to draw fresh air through
"exhaust fan" on the back of your Muse 3D. Note that accessories plugged into the back of yo
the work area.
Muse 3D will only turn on when the laser is fired (as intended to save power).
4.Connect to Power: Plug the exhaust fan power cord into the lower power plug marked "exhaust fan" on
the back of your Muse 3D. Note that accessories plugged into the back of your Muse 3D will only turn on
5. Fume Extractor Upgrade (optional):
when the laser is fired (as intended to save power).
extractors are air purifiers that clean the air through HEPA Filters. Fume extractors do not req
5.Fume Extractor Upgrade (optional): You can also upgrade to a fume extractor. Fume extractors are air
outside ventilation. This is a great choice for workshops that do not have the option to ventila
purifiers that clean the air through HEPA Filters. Fume extractors do not require outside ventilation. This is
outside. Both the extractors and the filters are available on the Full Spectrum Laser website a
a great choice for workshops that do not have the option to ventilate outside.
www.fslaser.com/Products/LaserAccessories. Ask a customer support representative which fu
Both the extractors and the filters are available on the Full Spectrum Laser website at
extractor is right for your needs.
http://fslaser.com/laser-accessories/
Small Fume Extractor
Ask a customer support representative which fume extractor is right for your needs.
Fume Extractor filters require routine cleaning and replacement, dependent on use and mater
Fume Extractor filters require routine cleaning and replacement, dependent on use and materials cut.
Generally, fume extractor suction will diminish and odors will be detected as filters clog.
Generally, fume extractor suction will diminish and odors will be detected as filters clog.
NEVER
use a fume extractor without all filters in place.
Follow these maintenance guidelines:
Pre-Filters
Maintenance guidelines:
Clean often. Use a shop vacuum to clean as debris builds. Check weekly, especially if cutting
Pre-Filters: Clean often. Use a shop vacuum to clean as debris builds. Check weekly, especially if cutting a lot
wood. When accumulated debris remains over 70% after cleaning, replace Pre-Filter.
of wood. When accumulated debris remains over 70% after cleaning, replace Pre-Filter.
HEPA Filters
HEPA Filters: Clean immediately when suction is reduced. Use a shop vacuum to clean accumulated dust.
Clean immediately when suction is reduced. Use a shop vacuum to clean accumulated dust. W
When cleaning does not return optimal suction power, replace HEPA Filter.
cleaning does not return optimal suction power, replace HEPA Filter.
Activated Carbon Filters: Clean when odors are detected or suction is reduced. Gently shake excess dust
Activated Carbon Filters
and debris from carbon filter and follow with a shop vacuum. When cleaning no longer eliminates detectable
odors, replace Activated Carbon Filters
Clean when odors are detected or suction is reduced. Gently shake excess dust and debris fr
carbon filter and follow with a shop vacuum. When cleaning no longer eliminates detectable o
replace Activated Carbon Filters.
https://www.fslaser.com/Products/LaserAccessories
Plug the exhaust fan power cord into the lower power plug marked
You can also upgrade to a fume extractor. Fume
Small Fume Extractor
Small Fume Extractor
NOTICE
Never use a fume extractor without all filters in place.
Technical Support is available 8am-5pm PST. Monday - Friday
https://www.fslaser.com/Products/LaserAccessories
You can also upgrade to a fume extractor. Fu
Medium Fume Extractor
Large Fume Extractor
support@fslaser.com • 702-802-3103
Medium Fume Extractor
14