Full Spectrum Laser MUSE 3D Operation Manual page 26

Section IV. Tests & Adjustments
1. Alignment Test
4. Close Safety Lid: Safety measures should make it impossible to fire the laser with the safety lid open.
4. Close Safety Lid:
Regardless, never attempt to fire the laser with safety lid open. Safety measures should make it impossible to fire the laser with the safety
lid open. Regardless, never attempt to fire the laser with safety lid open.
4. Close Safety Lid:
5. Test Fire the Laser: Press the Fire Laser Icon Button on the touch screen.
5. Test Fire the Laser:
Press the Fire Laser Icon Button on the touch screen.
lid open. Regardless, never attempt to fire the laser with safety lid open.
5. Test Fire the Laser:
ATTENTION!
Find and push this icon on your Muse 3D touch screen to test fire the laser.
touch screen to test fire the laser.
6. Repeat Test Fire in Other Three Corners: Without removing the thermal tape, repeat firing the laser once
6. Repeat Test Fire in Other Three Corners:
6. Repeat Test Fire in Other Three Corners:
firing the laser once in each of the other corners of the machine (Upper Right, Lower Right, and in each of the other corners of the machine (Upper Right, Lower Right, and Lower Left).
firing the laser once in each of the other corners of the machine (Upper Right, Lower Right, and
Lower Left).
Lower Left).
7. Check Results: With the forth corner test fire complete, open the lid and remove the thermal tape. The four
7. Check Results
: With the forth corner test fire complete, open the lid and remove the thermal
7. Check Results
burn marks should overlap each other perfectly (see illustration). If they do not overlap perfectly, you will need
tape. The four burn marks should overlap each other perfectly (see illustration). If they do not overlap
tape. The four burn marks should overlap each other perfectly (see illustration). If they do not overlap
to align the mirrors.
perfectly, you will need to align the mirrors.
perfectly, you will need to align the mirrors.
Figure 4.3
Figure 4.3
Not Aligned
PRO TIP!
will have two black dots from the test fires in the top and bottom
NOTICE
positions. The red laser pointer is aligned with the invisible laser
pointer so gives you immediate feedback on the mirror adjustment.
By adjusting it into the middle of the two black dots, you are splitting
the error difference. Usually after 1 or 2 iterations, the black dots will
be exactly on top and this axis is aligned. The goal is to have the two
black dots overlap exactly.
Technical Support is available from 8am to 5pm (PST) M - F at support@fslaser.com.
Safety measures should make it impossible to fire the laser with the safety
Press the Fire Laser Icon Button on the touch screen.
Find and push this icon on your Muse 3D
ATTENTION!
Find and push this icon on your Muse 3D
touch screen to test fire the laser.
Without removing the thermal tape, repeat
: With the forth corner test fire complete, open the lid and remove the thermal
Not Aligned
PRO TIP!
The idea is that when the laser is not aligned, you
will have two black dots from the test fires in the top and bottom
When the laser is not aligned, you will have two black dots from the test fires in the
positions. The red laser pointer is aligned with the invisible laser
The idea is that when the laser is not aligned, you
top and bottom positions. The red laser pointer is aligned with the invisible laser
pointer so gives you immediate feedback on the mirror adjustment.
By adjusting it into the middle of the two black dots, you are splitting
pointer so gives you immediate feedback on the mirror adjustment. By adjusting it
the error difference. Usually after 1 or 2 iterations, the black dots will
into the middle of the two black dots, you are splitting the error difference. Usually
be exactly on top and this axis is aligned. The goal is to have the two
black dots overlap exactly.
after 1 or 2 iterations, the black dots will be exactly on top and this axis is aligned.
The goal is to have the two black dots overlap exactly.
Technical Support is available from 8am to 5pm (PST) M - F at support@fslaser.com.
Technical Support is available 8am-5pm PST. Monday - Friday
support@fslaser.com
Without removing the thermal tape, repeat
Aligned
Aligned
• 702-802-3103
29
29
25