Full Spectrum Laser MUSE 3D Operation Manual page 90

Section VIII. Hardware & Maintenance
Belt Installation
The belts on your laser system are a consumable item and will eventually stretch beyond a usable length or
Belt Installation
break. You can contact Full Spectrum Laser support for replacements.
The belts on your laser system are a consumable item and will eventually stretch beyond a
usable
length or break. You can contact Full Spectrum Laser support for replacements.
WARNING
SHOCK WARNING!
retain power even after turning the laser off. To ensure your
safety, turn off the laser, remove the power cord and wait at
least 1 hour before accessing the power supply.
Required Parts and Tools
WATER WARNING!
system and working with the laser upside down. Be sure the
machine is dry before proceeding with this process.
• 2.5mm Hex key (included with accessories)
Belt Installation Instructions
REQUIRED PARTS AND TOOLS:
2.5mm Hex key (included with accessories)
1. Power Off Machine. Power off and unplug your unit. Wait at least 1 hour for capacitors to discharge.
1. BELT INSTALLATION STEPS:
2. Disconnect Water: Detach the tubes from the rear connectors. Use the small piece of tubing that
Power Off Machine. Power off and unplug your unit. Wait at least 1 hour for capacitors to discharge.
shipped with your laser to shunt the two water bulkheads together.
2. Disconnect Water:
3. Loosen Retaining Screws: Loosen or remove the M3 retaining screws and washers so that the old
that shipped with your laser to shunt the two water bulkheads together.
belt can be removed and discarded.
3. Loosen Retaining Screws:
4. Mount Belt: Run each end of the new belt through the mounting slot with the teeth on the inside of the
closed loop. The ends of the belt should protrude by approximately 3 teeth (6mm) through the slot. Make
the old belt can be removed and discarded.
sure that the belt forms a flat, closed loop.
4. Mount Belt:
Run each end of the new belt through the mounting slot with the teeth on the inside
5. Tighten Retaining Screws: Tighten the M3 retaining screws to secure and retain the belt.Starting the
of the closed loop. The ends of the belt should protrude by approximately 3 teeth (6mm) through the
thread with your fingers can speed the process up.
slot. Make sure that the belt forms a flat, closed loop.
6. Loosen the idler pulley mount: Once the belt has been installed on the riser, loop over the drive and
5. Tighten Retaining Screws:
idler pulleys.
Starting the thread with your fingers can speed the process up.
7. Tension the belt: Pull on the Y idler pulley mount with your hand. Moderate to strong force is
6. Loosen the idler pulley mount:
recommended. If the motors do not jog, verify that the motors are connected to the control card.
drive and idler pulleys.
7. Tension the belt:
Pull on the Y idler pulley mount with your hand. Moderate to strong force is
recommended. If the motors do not jog, verify that the motors are connected to the control card.
Technical Support is available from 8am to 5pm (PST) M - F at support@fslaser.com.
• The capacitors in the power supply retain power even after turning the laser off.
To ensure your safety, turn off the laser, remove the power cord and wait at least
1 hour before accessing the power supply.
The capacitors in the power supply
• You will be disconnecting the water system and working with the laser upside
down. Be sure the machine is dry before proceeding with this process.
You will be disconnecting the water
Detach the tubes from the rear connectors. Use the small piece of tubing
Loosen or remove the M3 retaining screws and washers so that
Tighten the M3 retaining screws to secure and retain the belt.
Once the belt has been installed on the riser, loop over the
Technical Support is available 8am-5pm PST. Monday - Friday
support@fslaser.com
92
• 702-802-3103
89