Kenwood TK-2170 Series Function Reference page 83

18.3.6 Transpond (Conventional)
This function allows the caller to confirm that the receiving
party has received the individual call code.
Transceiver operation when the receiving party receives
the code can be configured.
Configuration
Off Transceiver does not respond.
The transceiver multiplexes the Transpond
Alert
Tone and transmits the tone.
The transceiver multiplexes the ID Code
ID Code configured for the receive channel and
sends the code.
The transceiver multiplexes the Autodial
Transpond Code
Memory 1 and sends the code.
The transceiver multiplexes the Ringing
Ringing Tone
tone and transmits the tone.
Transpond can be configured by using KPG-101D.
(Refer to FPRG 6.10.2 Decode Tab - Transpond
(Conventional).)
Note: Transpond is available in Conventional Group.
18.3.7 Code (Trunking) (TK-3173 only)
The standby DTMF code for receiving an individual call in
Trunking System can be configured.
The transceiver executes the operation configured for
Transpond and Alert Tone if the DTMF code matches.
The transceiver can communicate only with LTR ID.
Code can be configured by using KPG-101D. (Refer to
FPRG 6.10.2 Decode Tab - Code (Trunking).)
Note: Code (Trunking) is available in Trunking System.
18.3.8 Transpond/ Alert Tone
(Trunking) (TK-3173 only)
The transceiver executes Transpond/ Alert Tone if the
code matches in Trunking System. If the code matches,
the transceiver executes the operation configured for
Transpond and Alert Tone.
Transpond and Alert Tone can be configured by using
KPG-101D. Below is a list of configuration items for Alert
Tone and Transpond.
Table 18-4 Transpond/ Alert Tone Operation
Configuration
The transceiver emits the configured Alert
Alert Tone
Tone.
The transceiver transponds, multiplexes
Transpond the Transpond tone and transmits the
tone.
FUNC (K)/Ver. 1.01
Operation
Operation
Confidential
Note:
The transceiver emits the alert tone after transponding when
both Transpond and Alert Tone are configured at the same time.
Alert Tone is delayed if the transmission of the Transpond is
delayed when the channel is being used while Clear To
Transpond is enabled in the Conventional Group.
The transceiver stops emitting the alert tone if a key is pressed
while the transceiver intermittently emits the alert tone when
"Infinite" is selected for Special Alert Tone window > >Cycle
edit box. The received tone is emitted first if the transceiver
intermittently emits the alert tone.
The matching status of DTMF is reset in the following conditions:
Table 18-5 Conditions for Resetting DTMF
Matching Status
Operation
If one of the following keys is pressed:
•
Monitor key
•
Monitor Momentary key
•
Squelch Off key
•
Squelch Off Momentary key
•
Zone Up key
•
Zone Down key
Pressing a
•
key Zone Up/Down key
•
CH/GID Up key
•
CH/GID Down key
•
CH/GID Up/Down key
•
Scan key
•
Home Channel key
•
Direct CH/GID 1 to Direct CH/GID 4 keys
Expiration of
When the Auto Reset Timer expires.
Timers
• The status of Transpond is reset in the following
conditions:
Table 18-6 Conditions for Resetting Transpond
Operation
If one of the following keys is pressed:
•
Monitor key
•
Monitor Momentary key
•
Squelch Off key
•
Squelch Off Momentary key
•
Zone Up key
•
Zone Down key
Pressing a
•
key Zone Up/Down key
•
CH/GID Up key
•
CH/GID Down key
•
CH/GID Up/Down key
•
Scan key
•
Home Channel key
•
Direct CH/GID 1 to Direct CH/GID 4 keys
Transmission When the PTT switch is pressed to transmit.
18 DTMF
Condition
Condition
Contents Index
71