Danfoss VLT HVAC Drive FC 102 Design Manual page 52

Specifications
®
VLT HVAC Drive FC 102
Normal overload
(Normal overload=110% current during 60 s)
Typical shaft output at 400 V [kW]
Typical shaft output at 460 V [hp]
Typical shaft output at 480 V [kW]
Enclosure size
Output current (3-phase)
Continuous (at 400 V) [A]
Intermittent (60 s overload)
(at 400 V) [A]
Continuous (at 460/480 V) [A]
Intermittent (60 s overload)(at 460/480 V) [A]
Continuous kVA (at 400 V) [kVA]
Continuous kVA (at 460 V) [kVA]
Continuous kVA (at 480 V) [kVA]
Maximum input current
7 7
Continuous (at 400 V) [A]
Continuous (at 460/480 V) [A]
Maximum number and size of cables per phase
2
- Motor [mm (AWG)]
- Mains [mm 2 (AWG)] (F2)
2
- Mains [mm (AWG)] (F4)
- Load share [mm
- Brake [mm 2 (AWG)]
Maximum external mains fuses [A]
Estimated power loss at 400 V [W]
Estimated power loss at 460 V [W]
Maximum added losses A1 RFI, circuit breaker or disconnect, and contactor [W], (F4 only)
Maximum panel options losses [W]
3)
Efficiency
Output frequency [Hz]
Control card overtemperature trip [°C (°F)]
Table 7.3 Electrical Data for Enclosures F2/F4, Mains Supply 3x380–480 V AC
1) For fuse ratings, see chapter 10.5 Fuses and Circuit Breakers.
2) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies for
dimensioning of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control
card power consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-
efficiency-directive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for
slots A and B each add only 4 W.
3) Measured using 5 m (16.5 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy
efficiency class, see chapter 10.12 Efficiency. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
50
VLT
2
(AWG)]
1)
2), 3)
2), 3)
Danfoss A/S © 11/2017 All rights reserved.
®
HVAC Drive FC 102
± 15% (tolerance relates to variety in voltage and cable conditions). These
P800 P1000
NO NO
800 1000
1200 1350
1000 1100
F2/F4 F2/F4
1460 1720
1606 1892
1380 1530
1518 1683
1012 1192
1100 1219
1195 1325
1407 1658
1330 1474
12x150 (12x300 12x150 (12x300
mcm) mcm)
8x240 (8x500 mcm) 8x240 (8x500 mcm)
8x456 (8x900 mcm) 8x456 (8x900 mcm)
4x120 (4x250 mcm) 4x120 (4x250 mcm)
6x185 (6x350 mcm) 6x185 (6x350 mcm)
2500 2500
17293 19278
16229 16624
2280 2541
400 400
0.98 0.98
0–590 0–590
85 (185) 85 (185)
MG16C302