Danfoss VLT HVAC Drive FC 102 Design Manual page 59

Specifications
®
VLT HVAC Drive FC 102
Normal overload
(Normal overload=110% current during 60 s)
Typical shaft output at 550 V [kW]
Typical shaft output at 575 V [hp]
Typical shaft output at 690 V [kW]
Enclosure size
Output current (3-phase)
Continuous (at 550 V) [A]
Intermittent (60 s overload) (at 550 V) [A]
Continuous (at 575/690 V) [A]
Intermittent (60 s overload) (at 575/690 V) [A]
Continuous kVA (at 550 V) [kVA]
Continuous kVA (at 575 V) [kVA]
Continuous kVA (at 690 V) [kVA]
Maximum input current
Continuous (at 550 V) [A]
Continuous (at 575 V) [A]
Continuous (at 690 V)
Maximum number and size of cables per phase
2
- Motor [mm (AWG)]
- Mains [mm 2 (AWG)]
2
- Brake [mm (AWG)]
Maximum external mains fuses [A]
Estimated power loss at 600 V [W]
Estimated power loss at 690 V [W]
Efficiency 3)
Output frequency [Hz]
Control card overtemperature trip [°C (°F)]
Table 7.10 Electrical Data for Enclosures F8/F9, Mains Supply 6x525–690 V AC
1) For fuse ratings, see chapter 10.5 Fuses and Circuit Breakers.
2) Typical power loss is at normal conditions and expected to be within
values are based on a typical motor efficiency (IE/IE3 border line). Lower efficiency motors add to the power loss in the drive. Applies for
dimensioning of drive cooling. If the switching frequency is higher than the default setting, the power losses can increase. LCP and typical control
card power consumptions are included. For power loss data according to EN 50598-2, refer to drives.danfoss.com/knowledge-center/energy-
efficiency-directive/#/. Options and customer load can add up to 30 W to the losses, though usually a fully loaded control card and options for
slots A and B each add only 4 W.
3) Measured using 5 m (16.5 ft) shielded motor cables at rated load and rated frequency. Efficiency measured at nominal current. For energy
efficiency class, see chapter 10.12 Efficiency. For part load losses, see drives.danfoss.com/knowledge-center/energy-efficiency-directive/#/.
MG16C302
Design Guide
1)
2), 3)
2), 3)
Danfoss A/S © 11/2017 All rights reserved.
P450 P500
NO NO
355 400
450 500
450 500
F8/F9 F8/F9
470 523
517 575
450 500
495 550
448 498
448 498
538 598
453 504
434 482
434 482
4x240 (4x500 4x240 (4x500
mcm) mcm)
4x85 (4x3/0 4x85 (4x3/0
mcm) mcm)
2x185 (2x350 2x185 (2x350
mcm) mcm)
630 630
5323 6010
5529 6239
0.98 0.98
0–500 0–500
85 (185) 85 (185)
± 15% (tolerance relates to variety in voltage and cable conditions). These
P560 P630
NO NO
450 500
600 650
560 630
F8/F9 F8/F9
596 630
656 693
570 630
627 693
568 600
568 627
681 753
574 607
549 607
549 607
4x240 (4x500 4x240 (4x500
mcm) mcm)
4x85 (4x3/0 4x85 (4x3/0
mcm) mcm)
2x185 (2x350 2x185 (2x350
mcm) mcm)
630 630
7395 8209
7653 8495
0.98 0.98
0–500 0–500
85 (185) 85 (185)
57
7 7