Danfoss VLT HVAC Drive FC 102 Design Manual page 223

How to Order a Drive
13.2.3 Ordering Numbers for Kits
Type
Miscellaneous hardware
USB in door, E1 and F1–F13
Top entry - motor cables, F1/F3 Allows for the installation of motor cables through the top of the
Top entry - motor cables, F2/F4 Allows for the installation of motor cables through the top of the
Top entry - motor cables,
F8–F13
Top entry - mains cables, F1–F2 Allows for the installation of mains cables through the top of the
Top entry - mains cables, F3–F4
with disconnect
Top entry - mains cables, F3–F4 Allows for the installation of mains cables through the top of the
Top entry - mains cables,
F8–F13
Top entry - fieldbus cables, E2
Common motor terminals,
F1–F4
NEMA 3R enclosure, E2
Pedestal, E1–E2
Input options plate, E1–E2
MG16C302
Design Guide
Description
USB extension cord kit to allow access to the drive controls via laptop
computer without opening the drive.
motor side cabinet. Must be used with the common motor terminals
kit. Only for enclosures F1/F3.
motor side cabinet. Must be used with the common motor terminals
kit. Only for enclosures F2/F4.
Allows for the installation of motor cables through the top of the
motor side cabinet. Must be used with the common motor terminals
kit. Only for enclosures F8–F13.
mains side cabinet. The kit must be ordered with the common motor
terminals kit. Only for enclosures F1–F2.
Allows for the installation of mains cables through the top of the
mains side cabinet. The kit must be ordered with the common motor
terminals kit. Only for enclosures F3–F4 with disconnect.
mains side cabinet. The kit must be ordered with the common motor
terminals kit. Only for enclosures F3–F4.
Allows for the installation of mains cables through the top of the
mains side cabinet. The kit must be ordered with the common motor
terminals kit. Only for enclosures F8–F13.
Allows for the installation of fieldbus cables through the top of the
drive. The kit is IP20/Chassis when installed, but a different mating
connector can be used to increase the protection rating. Only for
enclosure E2.
Provides the busbars and hardware required to connect the motor
terminals from the paralleled inverters to a single terminal (per phase)
to accommodate the installation of the motor-side top entry kit. This
kit is equivalent to the common motor terminal option of a drive.
This kit is not required to install the motor-side top entry kit if the
common motor terminal option was specified when the drive was
ordered.
Also recommended to connect the output of a drive to an output
filter or output contactor. The common motor terminals eliminate the
need for equal cable lengths from each inverter to the common point
of the output filter (or motor).
Designed to be used with the IP00/IP20/Chassis drives to achieve an
ingress protection rating of NEMA 3R or NEMA 4. These enclosures are
intended for outdoor use to provide a degree of protection against
inclement weather. Only for enclosures E2.
The pedestal kit is a 400 mm (15.8 in) high pedestal that allows the
drive to be floor mounted. The front of the pedestal has openings for
input air to cool the power components. Only for enclosures E1–E2.
Allows fuses, disconnect/fuses, RFI, RFI/fuses, and RFI/disconnect/fuses
to be added. Only for enclosures E1–E2.
Danfoss A/S © 11/2017 All rights reserved.
Ordering number
E1–E2 – 130B1156
F1–F13 – 176F1784
400 mm (15.7 in) cabinet –
176F1838
600 mm (23.6 in) cabinet –
176F1839
400 mm (15.7 in) cabinet –
176F1840
600 mm (23.6 in) cabinet –
176F1841
Contact factory
400 mm (15.7 in) cabinet –
176F1832
600 mm (23.6 in) cabinet –
176F1833
400 mm (15.7 in) cabinet –
176F1834
600 mm (23.6 in) cabinet –
176F1835
400 mm (15.7 in) cabinet –
176F1836
600 mm (23.6 in) cabinet –
176F1837
Contact factory
176F1742
400 mm (15.7 in) cabinet –
176F1845
600 mm (23.6 in) cabinet –
176F1846
Welded enclosure – 176F0298
Rittal enclosure – 176F1852
176F6739
Contact factory
221
13 13