MasterCool 52225-MED Operating Instructions Manual page 9

0.36°F
f. The "Repeatability" is
4. Measuring surface temperature:
4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see
WICHTIGE ANMERKUNGEN
display. In this mode, you can get the target surface temperature.
icon stop flashing to be ready for next measurement.
4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will
be continuously updated.
REINIGUNG UND LAGERUNG:
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects.
Bitte stellen Sie sicher, dass die Sonde sauber ist, um einen akkuraten Messwert zu gewährleisten.
* Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature.
Das Sondenglas ist das empfindlichste Teil des Thermometers. Gehen Sie mit Vorsicht vor bei der Reinigung des
5. Power off: -2.5 ~ -3.1°F (-1.4 ~ -1.7 ° C).
Sondenglases, um Schäden zu vermeiden.
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life.
Press the "ON/MEM" button to power on the device. Forehead mode is the default mode. You can see the
0.36°F
(0.20 ° C)
5.2 Manually power off the device by pressing the "ON/MEM" button.
and hear two beep sounds (see figure 1). In this mode, you can hold the thermometer within 4 cm from the central forehead (Fig. 2) and press
• Verwenden Sie Alkohol- oder Wattetupfer, die mit 70%~75% Alkohol angefeuchtet sind, um das Sondenglas zu
Important Notes
the "START" button to get the forehead measurement. The time consuming for measurement might be 1 second. After each forehead
reinigen.
Press the "ON/MEM" button to power on the device. Forehead mode is the default mode. You can see the
Please make sure the probe is clean to ensure an accurate reading.
measurement, wait icon stop flashing to be ready for next measurement.
and hear two beep sounds (see figure 1). In this mode, you can hold the thermometer within 4 cm from the central forehead (Fig. 2) and press
Points for attention: The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
• Lassen Sie das Sondenglas mindestens 1 Minute lang vollständig abtrocknen.
the "START" button to get the forehead measurement. The time consuming for measurement might be 1 second. After each forehead
Press the "ON/MEM" button to power on the device. Forehead mode is the default mode. You can see the
a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its "oral-equivalent" value.
b. Before the measurement, the subject should stay in a stable environment for 5 minutes and avoid exercise, bath for 30mins.
and hear two beep sounds (see figure 1). In this mode, you can hold the thermometer within 4 cm from the central forehead (Fig. 2) and press
measurement, wait icon stop flashing to be ready for next measurement. b. Allow the probe to fully dry for at least 1 minute.
• Halten Sie das Gerät trocken und entfernt von Flüssigkeiten und direkter Sonneneinstrahlung.
Cleaning
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
the "START" button to get the forehead measurement. The time consuming for measurement might be 1 second. After each forehead
Points for attention: c. Keep the unit dry and away from any liquids and direct sunlight.
And Storage d. The "Clinical Bias" is -2.5 ~ -3.1°F
a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its "oral-equivalent" value. d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
measurement, wait icon stop flashing to be ready for next measurement.
• Lagertemperaturbereich: aufbewahrt bei Raumtemperatur, zwischen -20~+50°C (-4~122°F), Rel. Feuchte <85%
e. The "Limits of Agreement" is 0.98.
b. Before the measurement, the subject should stay in a stable environment for 5 minutes and avoid exercise, bath for 30mins.
Press the "ON/MEM" button to power on the device. Forehead mode is the default mode. You can see the
Points for attention: e. The Probe should not be submerged into liquids.
0.36°F
f. The "Repeatability" is
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
and hear two beep sounds (see figure 1). In this mode, you can hold the thermometer within 4 cm from the central forehead (Fig. 2) and press
• Die Sonde sollte nicht in Flüssigkeiten eingetaucht werden.
a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its "oral-equivalent" value.
Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
-2.5 ~ -3.1°F
d. The "Clinical Bias" is
4. Measuring surface temperature:
the "START" button to get the forehead measurement. The time consuming for measurement might be 1 second. After each forehead b. Before the measurement, the subject should stay in a stable environment for 5 minutes and avoid exercise, bath for 30mins.
This could make the body temperature measurement lower than usual.
e. The "Limits of Agreement" is 0.98.
4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
Das Thermometer zu lang in der Hand zu halten kann zu einem höheren Umgebungstemperatur-Messwert der Sonde
measurement, wait icon stop flashing to be ready for next measurement.
0.36°F
f. The "Repeatability" is
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries.
-2.5 ~ -3.1°F
display. In this mode, you can get the target surface temperature. d. The "Clinical Bias" is
Points for attention:
führen. Dies könnte die Körpertemperatur-Messung niedriger als üblich machen.
e. The "Limits of Agreement" is 0.98.
4. Measuring surface temperature: Press the "ON/MEM" button to power on the device. Forehead mode is the default mode. You can see the 4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its "oral-equivalent" value.
0.36°F
f. The "Repeatability" is
4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see
and hear two beep sounds (see figure 1). In this mode, you can hold the thermometer within 4 cm from the central forehead (Fig. 2) and press be continuously updated. Please make sure the probe is clean to ensure an accurate reading.
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
b. Before the measurement, the subject should stay in a stable environment for 5 minutes and avoid exercise, bath for 30mins.
Battery replacement
display. In this mode, you can get the target surface temperature.
BATTERIEWECHSEL: the "START" button to get the forehead measurement. The time consuming for measurement might be 1 second. After each forehead 4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects.
4. Measuring surface temperature:
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
3. Replace the battery cover. (See Figure 3)
Press the "ON/MEM" button to power on the device. Forehead mode is the default mode. You can see the
4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will
-2.5 ~ -3.1°F
4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see d. The "Clinical Bias" is
* Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature.
measurement, wait icon stop flashing to be ready for next measurement.
a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
and hear two beep sounds (see figure 1). In this mode, you can hold the thermometer within 4 cm from the central forehead (Fig. 2) and press
be continuously updated.
e. The "Limits of Agreement" is 0.98.
display. In this mode, you can get the target surface temperature.
Points for attention:
b. Allow the probe to fully dry for at least 1 minute.
5. Power off:
0.36°F
the "START" button to get the forehead measurement. The time consuming for measurement might be 1 second. After each forehead f. The "Repeatability" is
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects.
4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will
a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its "oral-equivalent" value.
c. Keep the unit dry and away from any liquids and direct sunlight.
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life.
measurement, wait * Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature. be continuously updated. b. Before the measurement, the subject should stay in a stable environment for 5 minutes and avoid exercise, bath for 30mins. icon stop flashing to be ready for next measurement.
4. Measuring surface temperature:
5.2 Manually power off the device by pressing the "ON/MEM" button.
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
Wenn das Symbol „Batterie niedrig" anzeigt, dass der Batteriezustand niedrig ist, sollte die Batterie sofort mit 2 St. AAA,
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects. Points for attention:
4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see
5. Power off: Important Notes
-2.5 ~ -3.1°F
d. The "Clinical Bias" is e. The Probe should not be submerged into liquids.
Figure 1
a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its "oral-equivalent" value.
display. In this mode, you can get the target surface temperature.
* Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature.
1,5V-Batterien ausgetauscht werden.
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life.
Please make sure the probe is clean to ensure an accurate reading.
e. The "Limits of Agreement" is 0.98.
b. Before the measurement, the subject should stay in a stable environment for 5 minutes and avoid exercise, bath for 30mins.
Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will
5.2 Manually power off the device by pressing the "ON/MEM" button. 0.36°F
f. The "Repeatability" is
5. Power off:
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
Trouble shooting:
The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
1. Öffnen Sie die Batterieabdeckung und schieben Sie diese mit dem Daumen heraus. (Siehe Abb. 1)
be continuously updated.
This could make the body temperature measurement lower than usual.
Important Notes
-2.5 ~ -3.1°F
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life. d. The "Clinical Bias" is
4. Measuring surface temperature: a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
Error Message
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects.
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries. e. The "Limits of Agreement" is 0.98.
5.2 Manually power off the device by pressing the "ON/MEM" button. Please make sure the probe is clean to ensure an accurate reading.
2. Setzen Sie die neuen AAA-Batterien (*2 Stück) ein, (siehe Abb. 2)
4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see b. Allow the probe to fully dry for at least 1 minute.
* Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature.
0.36°F
Cleaning f. The "Repeatability" is
Error 5~9, the system is not functioning properly.
Important Notes
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
display. In this mode, you can get the target surface temperature. The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage. c. Keep the unit dry and away from any liquids and direct sunlight.
And Storage
3. Fügen Sie die Batterieabdeckung wieder ein (siehe Abb. 3)
5. Power off:
4. Measuring surface temperature: Please make sure the probe is clean to ensure an accurate reading.
a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
Measurement before device stabilization.
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life. 4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see
b. Allow the probe to fully dry for at least 1 minute.
be continuously updated.
e. The Probe should not be submerged into liquids. The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
Cleaning 3. Replace the battery cover. (See Figure 3)
5.2 Manually power off the device by pressing the "ON/MEM" button. display. In this mode, you can get the target surface temperature.
c. Keep the unit dry and away from any liquids and direct sunlight.
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects.
a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
The ambient temperature is not within the range between 50 Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
And Storage
Important Notes
4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
b. Allow the probe to fully dry for at least 1 minute.
* Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature.
This could make the body temperature measurement lower than usual.
Cleaning
(1) In forehead mode: Temperature taken is higher than 108°F (+42.2
be continuously updated.
Please make sure the probe is clean to ensure an accurate reading.
e. The Probe should not be submerged into liquids. c. Keep the unit dry and away from any liquids and direct sunlight.
5. Power off:
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries.
And Storage
(2) In surface mode: Temperature taken is higher than 176°F (+80
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects.
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life.
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
(1) In forehead mode: Temperature taken is lower than 93.2°F (+34
* Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature.
e. The Probe should not be submerged into liquids. a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
This could make the body temperature measurement lower than usual.
5.2 Manually power off the device by pressing the "ON/MEM" button.
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
b. Allow the probe to fully dry for at least 1 minute.
Battery replacement
5. Power off: Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
Important Notes
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries.
Figure 1
Cleaning
3. Replace the battery cover. (See Figure 3)
c. Keep the unit dry and away from any liquids and direct sunlight.
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life. This could make the body temperature measurement lower than usual.
Device cannot be powered on to the ready stage.
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1) Please make sure the probe is clean to ensure an accurate reading.
And Storage
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
5.2 Manually power off the device by pressing the "ON/MEM" button.
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries.
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
Battery replacement e. The Probe should not be submerged into liquids.
Important Notes
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
Warranty: a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
3. Replace the battery cover. (See Figure 3)
FEHLERDIAGNOSE:
Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
Please make sure the probe is clean to ensure an accurate reading.
b. Allow the probe to fully dry for at least 1 minute.
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
Warranty: 12 months
Cleaning Battery replacement Error 5~9, the system is not functioning properly.
This could make the body temperature measurement lower than usual.
The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
c. Keep the unit dry and away from any liquids and direct sunlight.
Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.)
3. Replace the battery cover. (See Figure 3)
And Storage
Fehlermeldung Problem
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries. a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens. Figure 1
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture
Measurement before device stabilization.
b. Allow the probe to fully dry for at least 1 minute.
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
month, the others is the serial number. e. The Probe should not be submerged into liquids.
Cleaning
Trouble shooting:
c. Keep the unit dry and away from any liquids and direct sunlight.
Fehler 5~9, das System funktioniert nicht
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
And Storage
Battery replacement The ambient temperature is not within the range between 50
Error Message
Figure 1
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
events at any time, please contact the dealers or nearest service address.
This could make the body temperature measurement lower than usual.
3. Replace the battery cover. (See Figure 3)
ordnungsgemäß.
e. The Probe should not be submerged into liquids.
Warning: No modification of this equipment is allowed. (1) In forehead mode: Temperature taken is higher than 108°F (+42.2
Error 5~9, the system is not functioning properly.
Trouble shooting: When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries.
Figure 1
Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
(2) In surface mode: Temperature taken is higher than 176°F (+80
Please read the instructions for use
Error Message 1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
Measurement before device stabilization.
This could make the body temperature measurement lower than usual.
(1) In forehead mode: Temperature taken is lower than 93.2°F (+34
Trouble shooting:
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
Radiant Innovation Inc.
Error 5~9, the system is not functioning properly.
Battery replacement
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries.
Error Message
Http://www.radiantek.com.tw The ambient temperature is not within the range between 50 3. Replace the battery cover. (See Figure 3)
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
Messung vor Gerätestabilisierung.
Measurement before device stabilization. Figure 1
Add: 1F, No.3, Industrial East 9 Road,
th
Device cannot be powered on to the ready stage. Error 5~9, the system is not functioning properly.
(1) In forehead mode: Temperature taken is higher than 108°F (+42.2
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
Science-Based Industrial Park, HsinChu, Taiwan 300.
Battery replacement
(2) In surface mode: Temperature taken is higher than 176°F (+80
Trouble shooting:
3. Replace the battery cover. (See Figure 3)
The ambient temperature is not within the range between 50
Measurement before device stabilization.
(1) Die Umgebungstemperatur liegt nicht In forehead mode: Temperature taken is lower than 93.2°F (+34
Error Message
(1) (2) In forehead mode: Temperature taken is higher than 108°F (+42.2 In surface mode: Temperature taken is lower than –7.6°F (-22
innerhalb des Bereichs, zwischen 10°C~40°C
The ambient temperature is not within the range between 50
(2) In surface mode: Temperature taken is higher than 176°F (+80
Error 5~9, the system is not functioning properly.
Figure 1
Device cannot be powered on to the ready stage.
(1) (50°F~104°F) In forehead mode: Temperature taken is lower than 93.2°F (+34
(1) In forehead mode: Temperature taken is higher than 108°F (+42.2
Measurement before device stabilization.
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
Trouble shooting:
(2) In surface mode: Temperature taken is higher than 176°F (+80
Warranty: (1) Figure 1 In forehead mode: Temperature taken is lower than 93.2°F (+34
Error Message (1) Im Stirn-Modus: gemessene Temperatur ist
The ambient temperature is not within the range between 50
Device cannot be powered on to the ready stage.
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
Warranty: 12 months
Error 5~9, the system is not functioning properly. höher als 108°F (42,2°C)
Trouble shooting:
(1) In forehead mode: Temperature taken is higher than 108°F (+42.2
Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.)
Device cannot be powered on to the ready stage.
Warranty: Error Message
(2) (2) Im Oberflächen-Modus: gemessene In surface mode: Temperature taken is higher than 176°F (+80
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture
Measurement before device stabilization.
Warranty: 12 months month, the others is the serial number. (1) In forehead mode: Temperature taken is lower than 93.2°F (+34
Error 5~9, the system is not functioning properly.
Temperatur ist höher als 80°C (176°F)
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.) Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected Warranty:
The ambient temperature is not within the range between 50
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture events at any time, please contact the dealers or nearest service address.
Warranty: 12 months Measurement before device stabilization.
(1) (1) Im Stirn-Modus: gemessene Temperatur ist In forehead mode: Temperature taken is higher than 108°F (+42.2
Device cannot be powered on to the ready stage.
month, the others is the serial number.
Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.) Warning: No modification of this equipment is allowed.
(2) In surface mode: Temperature taken is higher than 176°F (+80
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture The ambient temperature is not within the range between 50
Road, niedriger als +34°C ( 93,2°F)
th
Please read the instructions for use
(1) In forehead mode: Temperature taken is lower than 93.2°F (+34
events at any time, please contact the dealers or nearest service address.
Warranty: month, the others is the serial number.
(1) In forehead mode: Temperature taken is higher than 108°F (+42.2
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
(2) Im Oberflächen-Modus: gemessene
Radiant Innovation Inc.
Warning: No modification of this equipment is allowed.
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected
Warranty: 12 months
(2) In surface mode: Temperature taken is higher than 176°F (+80
Http://www.radiantek.com.tw
events at any time, please contact the dealers or nearest service address.
Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.) Temperatur ist niedriger als -22°C (-7,6°F)
Please read the instructions for use Device cannot be powered on to the ready stage.
(1) In forehead mode: Temperature taken is lower than 93.2°F (+34
Add: 1F, No.3, Industrial East 9 Road,
th
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture Warning: No modification of this equipment is allowed.
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
Radiant Innovation Inc.
Science-Based Industrial Park, HsinChu, Taiwan 300.
month, the others is the serial number.
Gerät kann nicht in den Bereitschaftszustand
Please read the instructions for use
Warranty:
Http://www.radiantek.com.tw
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected
Device cannot be powered on to the ready stage.
Add: 1F, No.3, Industrial East 9 Warranty: 12 months eingeschaltet werden. Road,
th
Radiant Innovation Inc.
events at any time, please contact the dealers or nearest service address.
Science-Based Industrial Park, HsinChu, Taiwan 300. Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.)
Http://www.radiantek.com.tw
Warning: No modification of this equipment is allowed.
Warranty:
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture
Add: 1F, No.3, Industrial East 9 Road,
th
Please read the instructions for use
Warranty: 12 months
month, the others is the serial number.
Science-Based Industrial Park, HsinChu, Taiwan 300.
Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.)
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected
Radiant Innovation Inc.
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture
events at any time, please contact the dealers or nearest service address.
Http://www.radiantek.com.tw
month, the others is the serial number.
Warning: No modification of this equipment is allowed.
Add: 1F, No.3, Industrial East 9 Road,
th
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected
Science-Based Industrial Park, HsinChu, Taiwan 300.
Please read the instructions for use
events at any time, please contact the dealers or nearest service address.
Radiant Innovation Inc. Warning: No modification of this equipment is allowed.
Http://www.radiantek.com.tw
Please read the instructions for use
Add: 1F, No.3, Industrial East 9 Road,
th
(0.20 ° C)
(-1.4 ~ -1.7 ° C).
(0.20 ° C)
(-1.4 ~ -1.7 ° C).
(0.20 ° C)
(-1.4 ~ -1.7 ° C).
(0.20 ° C)
(-1.4 ~ -1.7 ° C).
(0.20 ° C)
(-1.4 ~ -1.7 ° C).
Figure 2
(0.20 ° C)
(-1.4 ~ -1.7 ° C).
Problem
(0.20 ° C)
Figure 2
Problem
Figure 2
o F~104
Figure 2
Problem
Figure 2
BF type applied part
Problem
Problem
Figure 2
Ref No.：032020
Problem
Figure 2
Figure 2
Problem
Problem
BF type applied part
BF type applied part
Ref No.：032020
BF type applied part
Ref No.：032020
BF type applied part
Ref No.：032020
BF type applied part
Ref No.：032020
BF type applied part
Ref No.：032020
BF type applied part
icon on the screen
Figure 3
Unload the battery, wait for 1 minute and repower it. If the message
reappears, contact the retailer for service.
Wait for "Er1" to disappear.
Allow the thermometer to rest in a room for at least 15 minutes at room
o F~104 o F (10 o C~40 o C).
temperature: 50
o C)
o C) Please select the target within specifications. If a malfunction still exists,
please contact the nearest retailer.
o C)
o C)
Figure 3
Change with a new battery.
Unload the battery, wait for 1 minute and repower it. If the message
reappears, contact the retailer for service.
Lösung
Figure 3
Wait for "Er1" to disappear.
Entladen Sie die Batterien, warten Sie 1
Allow the thermometer to rest in a room for at least 15 minutes at room
o F (10 o C~40 o C).
Figure 3
temperature: 50
Minute und schalten Sie erneut ein. Falls die
Unload the battery, wait for 1 minute and repower it. If the message
o C)
reappears, contact the retailer for service.
Figure 3 Fehlermeldung nochmals erscheint, kontaktieren
o C) Please select the target within specifications. If a malfunction still exists,
Wait for "Er1" to disappear.
please contact the nearest retailer.
o C)
Sie den Kundendienst.
Unload the battery, wait for 1 minute and repower it. If the message
o C)
Allow the thermometer to rest in a room for at least 15 minutes at room
reappears, contact the retailer for service.
o F~104 o F (10 o C~40 o C).
temperature: 50
Warten Sie, bis "Er1" verschwindet.
Unload the battery, wait for 1 minute and repower it. If the message
Figure 3 Wait for "Er1" to disappear.
Change with a new battery.
o C)
reappears, contact the retailer for service.
Allow the thermometer to rest in a room for at least 15 minutes at room
o C) Please select the target within specifications. If a malfunction still exists,
o F~104 o F (10 o C~40 o C).
Wait for "Er1" to disappear.
please contact the nearest retailer.
temperature: 50
o C) Lassen Sie das Thermometer mindestens 15
o C) o C)
Allow the thermometer to rest in a room for at least 15 minutes at room
Minuten in einem Raum, bei Raumtemperatur,
Unload the battery, wait for 1 minute and repower it. If the message
o F~104 o F (10 o C~40 o C).
o C) Please select the target within specifications. If a malfunction still exists,
temperature: 50
Figure 3
reappears, contact the retailer for service.
Change with a new battery.
please contact the nearest retailer.
o C) ruhen: 10°C~40°C (50°F~104°F)
o C)
Wait for "Er1" to disappear.
o C)
o C) Please select the target within specifications. If a malfunction still exists,
please contact the nearest retailer.
o Figure 3 C)
Allow the thermometer to rest in a room for at least 15 minutes at room
o F~104 o F (10 o C~40 o C).
Change with a new battery.
o C)
temperature: 50
Unload the battery, wait for 1 minute and repower it. If the message
reappears, contact the retailer for service.
o C)
Change with a new battery.
o C) Please select the target within specifications. If a malfunction still exists,
Wait for "Er1" to disappear.
Bitte wählen Sie das Ziel innerhalb der
please contact the nearest retailer.
Unload the battery, wait for 1 minute and repower it. If the message
o C)
Allow the thermometer to rest in a room for at least 15 minutes at room
reappears, contact the retailer for service.
Spezifikationen aus. Falls immer noch eine
o C)
o F~104 o F (10 o C~40 o C).
temperature: 50
Wait for "Er1" to disappear.
Fehlfunktion besteht, kontaktieren Sie bitte den
o C)
Change with a new battery.
Allow the thermometer to rest in a room for at least 15 minutes at room
o C) Please select the target within specifications. If a malfunction still exists,
Kundendienst.
o F~104 o F (10 o C~40 o C).
temperature: 50
please contact the nearest retailer.
o C)
o C)
o C)
o C) Please select the target within specifications. If a malfunction still exists,
please contact the nearest retailer.
Change with a new battery.
o C)
o C)
Setzen Sie neue Batterien ein.
Change with a new battery.
www.mastercool.com
icon on the screen
icon on the screen
icon on your LCD
icon on the screen
icon on the screen
icon on the screen
icon on the screen
Solution
o F~104 o F (10 o C~40 o C).
Solution
Solution
o F~104 o F (10 o C~40 o C).
Solution
Solution
o F~104 o F (10 o C~40 o C).
o F~104 o F (10 o C~40 o C).
Solution
o F~104 o F (10 o C~40 o C).
Solution
o F~104 o F (10 o C~40 o C).
Solution
o F~104 o F (10 o C~40 o C).
o F~104 o F (10 o C~40 o C).
icon on your LCD
Figure 2
Figure 2
Figure 2
Figure 2
icon on your LCD
Figure 2
icon on your LCD
Figure 2
icon on your LCD
Figure 2
icon on your LCD
icon on your LCD
icon on your LCD
9