Troubleshooting - MasterCool 52225-MED Operating Instructions Manual

4. Measuring surface temperature:
4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see
display. In this mode, you can get the target surface temperature.
4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will
IMPORTANT NOTES
be continuously updated.
icon stop flashing to be ready for next measurement.
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects.
CLEANING AND STORAGE:
* Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature.
Please make sure the probe is clean to ensure an accurate reading.
5. Power off:
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life. The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid
-2.5 ~ -3.1°F (-1.4 ~ -1.7 ° C).
Press the "ON/MEM" button to power on the device. Forehead mode is the default mode. You can see the
5.2 Manually power off the device by pressing the "ON/MEM" button.
damage.
and hear two beep sounds (see figure 1). In this mode, you can hold the thermometer within 4 cm from the central forehead (Fig. 2) and press
Important Notes
0.36°F
(0.20 ° C)
the "START" button to get the forehead measurement. The time consuming for measurement might be 1 second. After each forehead
• Use alcohol or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
Press the "ON/MEM" button to power on the device. Forehead mode is the default mode. You can see the Please make sure the probe is clean to ensure an accurate reading.
and hear two beep sounds (see figure 1). In this mode, you can hold the thermometer within 4 cm from the central forehead (Fig. 2) and press
measurement, wait icon stop flashing to be ready for next measurement.
The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
• Allow the probe to fully dry for at least 1 minute.
the "START" button to get the forehead measurement. The time consuming for measurement might be 1 second. After each forehead Points for attention:
Press the "ON/MEM" button to power on the device. Forehead mode is the default mode. You can see the
a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its "oral-equivalent" value.
and hear two beep sounds (see figure 1). In this mode, you can hold the thermometer within 4 cm from the central forehead (Fig. 2) and press
b. Allow the probe to fully dry for at least 1 minute.
measurement, wait icon stop flashing to be ready for next measurement.
• Keep the unit dry and away from any liquids and direct sunlight.
Cleaning
b. Before the measurement, the subject should stay in a stable environment for 5 minutes and avoid exercise, bath for 30mins.
the "START" button to get the forehead measurement. The time consuming for measurement might be 1 second. After each forehead
Points for attention: c. Keep the unit dry and away from any liquids and direct sunlight.
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
And Storage
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its "oral-equivalent" value.
measurement, wait icon stop flashing to be ready for next measurement.
• Storage temperature range: stored at room temperature between -4~122°F (-20~+50°C), RH≤85%
-2.5 ~ -3.1°F
d. The "Clinical Bias" is
b. Before the measurement, the subject should stay in a stable environment for 5 minutes and avoid exercise, bath for 30mins.
Press the "ON/MEM" button to power on the device. Forehead mode is the default mode. You can see the
e. The Probe should not be submerged into liquids.
Points for attention:
e. The "Limits of Agreement" is 0.98.
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
and hear two beep sounds (see figure 1). In this mode, you can hold the thermometer within 4 cm from the central forehead (Fig. 2) and press
• The probe should not be submerged into liquids. 0.36°F
f. The "Repeatability" is a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its "oral-equivalent" value.
Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
-2.5 ~ -3.1°F
d. The "Clinical Bias" is
b. Before the measurement, the subject should stay in a stable environment for 5 minutes and avoid exercise, bath for 30mins.
the "START" button to get the forehead measurement. The time consuming for measurement might be 1 second. After each forehead
This could make the body temperature measurement lower than usual.
4. Measuring surface temperature: e. The "Limits of Agreement" is 0.98.
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
Holding the thermometer too long may cause a higher ambient temperature reading of the probe. This could make
measurement, wait icon stop flashing to be ready for next measurement.
f. The "Repeatability" is 0.36°F
4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries.
-2.5 ~ -3.1°F
d. The "Clinical Bias" is
Points for attention:
the body temperature measurement lower than usual. display. In this mode, you can get the target surface temperature.
e. The "Limits of Agreement" is 0.98.
4. Measuring surface temperature:
Press the "ON/MEM" button to power on the device. Forehead mode is the default mode. You can see the 1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its "oral-equivalent" value.
4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will 0.36°F
f. The "Repeatability" is
4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see and hear two beep sounds (see figure 1). In this mode, you can hold the thermometer within 4 cm from the central forehead (Fig. 2) and press
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
b. Before the measurement, the subject should stay in a stable environment for 5 minutes and avoid exercise, bath for 30mins.
Battery replacement
be continuously updated.
BATTERY REPLACEMENT: display. In this mode, you can get the target surface temperature.
the "START" button to get the forehead measurement. The time consuming for measurement might be 1 second. After each forehead
4. Measuring surface temperature:
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
3. Replace the battery cover. (See Figure 3)
Please make sure the probe is clean to ensure an accurate reading.
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects.
Press the "ON/MEM" button to power on the device. Forehead mode is the default mode. You can see the
4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will
-2.5 ~ -3.1°F
d. The "Clinical Bias" is
4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see
measurement, wait icon stop flashing to be ready for next measurement.
The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
and hear two beep sounds (see figure 1). In this mode, you can hold the thermometer within 4 cm from the central forehead (Fig. 2) and press * Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature.
be continuously updated.
e. The "Limits of Agreement" is 0.98.
display. In this mode, you can get the target surface temperature.
Points for attention:
the "START" button to get the forehead measurement. The time consuming for measurement might be 1 second. After each forehead 0.36°F
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects. f. The "Repeatability" is a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will
5. Power off: a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its "oral-equivalent" value.
b. Allow the probe to fully dry for at least 1 minute.
measurement, wait * Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature. be continuously updated. b. Before the measurement, the subject should stay in a stable environment for 5 minutes and avoid exercise, bath for 30mins. icon stop flashing to be ready for next measurement.
4. Measuring surface temperature:
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life.
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
When the "low battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects. Points for attention: c. Keep the unit dry and away from any liquids and direct sunlight.
4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see
5.2 Manually power off the device by pressing the "ON/MEM" button.
5. Power off:
-2.5 ~ -3.1°F
d. The "Clinical Bias" is
Figure 1
a. Forehead temperature is displayed in oral mode. This mode converts the forehead temperature to display its "oral-equivalent" value.
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
* Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature. display. In this mode, you can get the target surface temperature.
Important Notes
batteries.
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life.
e. The "Limits of Agreement" is 0.98.
b. Before the measurement, the subject should stay in a stable environment for 5 minutes and avoid exercise, bath for 30mins.
4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will
e. The Probe should not be submerged into liquids.
Please make sure the probe is clean to ensure an accurate reading.
5.2 Manually power off the device by pressing the "ON/MEM" button.
f. The "Repeatability" is 0.36°F
5. Power off:
c. Remember to keep the forehead area clean and away from sweat, cosmetics and scar while taking temperature.
Trouble shooting:
1. Open the battery cover, use your thumbs to push battery cover out.
be continuously updated.
Important Notes
-2.5 ~ -3.1°F
d. The "Clinical Bias" is
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life. Holding the thermometer too long may cause a higher ambient temperature reading of the probe. The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
4. Measuring surface temperature:
Error Message
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects.
(see figure 1)
e. The "Limits of Agreement" is 0.98.
5.2 Manually power off the device by pressing the "ON/MEM" button. Please make sure the probe is clean to ensure an accurate reading. a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
This could make the body temperature measurement lower than usual.
4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see
* Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature.
0.36°F
f. The "Repeatability" is
Error 5~9, the system is not functioning properly.
Important Notes
b. Allow the probe to fully dry for at least 1 minute.
The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
display. In this mode, you can get the target surface temperature.
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries.
Cleaning
2. Insert the new AAA (*2 pcs) batteries. (see figure 2)
c. Keep the unit dry and away from any liquids and direct sunlight.
4. Measuring surface temperature: 5. Power off:
Please make sure the probe is clean to ensure an accurate reading.
a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will
And Storage
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1) Measurement before device stabilization.
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life. 4.1 After power on, press and hold the "ON/MEM" button, and press the "START" button one time for "Infrared thermometer" mode to see
be continuously updated. b. Allow the probe to fully dry for at least 1 minute.
The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
3. Replace the battery cover. (see figure 3)
Cleaning
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
5.2 Manually power off the device by pressing the "ON/MEM" button. display. In this mode, you can get the target surface temperature. e. The Probe should not be submerged into liquids.
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects. c. Keep the unit dry and away from any liquids and direct sunlight.
a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
The ambient temperature is not within the range between 50
And Storage
Important Notes 4.2 When you press the "START" button, you will get the real time temperature immediately. If you press and hold the "START" button, the reading of measurement will
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
3. Replace the battery cover. (See Figure 3)
* Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature. Holding the thermometer too long may cause a higher ambient temperature reading of the probe. b. Allow the probe to fully dry for at least 1 minute.
Cleaning
be continuously updated. (1) In forehead mode: Temperature taken is higher than 108°F (+42.2
Please make sure the probe is clean to ensure an accurate reading.
e. The Probe should not be submerged into liquids.
This could make the body temperature measurement lower than usual. c. Keep the unit dry and away from any liquids and direct sunlight.
5. Power off:
And Storage
(2) In surface mode: Temperature taken is higher than 176°F (+80
4.3 Applications include temperature measurements for water, milk, cloth, skin or other objects.
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries. Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life.
(1) In forehead mode: Temperature taken is lower than 93.2°F (+34
* Note: This mode shows the actual and unadjusted surface temperature which is different from the body temperature.
e. The Probe should not be submerged into liquids. a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
This could make the body temperature measurement lower than usual.
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
5.2 Manually power off the device by pressing the "ON/MEM" button.
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
b. Allow the probe to fully dry for at least 1 minute.
5. Power off:
Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
Important Notes When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries.
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
Cleaning
Battery replacement
c. Keep the unit dry and away from any liquids and direct sunlight.
5.1 Device will automatically shut off if left idle for more than 1 minute to extend battery life.
This could make the body temperature measurement lower than usual.
Device cannot be powered on to the ready stage.
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1) Please make sure the probe is clean to ensure an accurate reading.
And Storage
3. Replace the battery cover. (See Figure 3)
Figure 1
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
5.2 Manually power off the device by pressing the "ON/MEM" button.
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries.
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.
Battery replacement e. The Probe should not be submerged into liquids.
Important Notes
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
Warranty: a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
3. Replace the battery cover. (See Figure 3)
Please make sure the probe is clean to ensure an accurate reading.
Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
b. Allow the probe to fully dry for at least 1 minute.
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
Warranty: 12 months
Battery replacement
Cleaning
This could make the body temperature measurement lower than usual.
The probe lens is the most delicate part of the thermometer. Use with care when cleaning the probe lens to avoid damage.

TROUBLESHOOTING:

c. Keep the unit dry and away from any liquids and direct sunlight.
Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.)
3. Replace the battery cover. (See Figure 3)
And Storage
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries. a. Use alcohol swabs or cotton swabs moistened with 70%~75% alcohol to clean the probe lens.
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
Error 5~9, the system is not functioning properly.
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture
Figure 1
b. Allow the probe to fully dry for at least 1 minute.
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
e. The Probe should not be submerged into liquids.
month, the others is the serial number.
Error Message Problem
Cleaning
c. Keep the unit dry and away from any liquids and direct sunlight.
Measurement before device stabilization.
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
Trouble shooting: And Storage Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
Battery replacement
Figure 1
d. Storage temperature range: It should be stored at room temperature between -4~122°F (-20~+50°C), RH ≦ 85%
events at any time, please contact the dealers or nearest service address.
3. Replace the battery cover. (See Figure 3) This could make the body temperature measurement lower than usual.
Error 5~9, the system is not functioning properly. Unload the batteries, wait for 1 minute and
Error Message
e. The Probe should not be submerged into liquids.
The ambient temperature is not within the range between 50
Warning: No modification of this equipment is allowed.
Trouble shooting: When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries.
Figure 1
Error 5~9, the system is not functioning properly.
Holding the thermometer too long may cause a higher ambient temperature reading of the probe.
Error Message Please read the instructions for use (1) In forehead mode: Temperature taken is higher than 108°F (+42.2 1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
This could make the body temperature measurement lower than usual.
Trouble shooting:
(2) In surface mode: Temperature taken is higher than 176°F (+80
Measurement before device stabilization. 2. Insert the new AAA *2 pcs batteries. (See Figure 2)
Radiant Innovation Inc.
Error 5~9, the system is not functioning properly.
Battery replacement
When the "Low Battery" icon indicates the battery is low, the battery should be replaced immediately with AAA *2 pcs batteries.
Error Message (1) In forehead mode: Temperature taken is lower than 93.2°F (+34
3. Replace the battery cover. (See Figure 3)
Http://www.radiantek.com.tw
1. Open the battery cover: Use the thumbs to push battery cover out. (See Figure 1)
Measurement before device stabilization.
The ambient temperature is not within the range between 50
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
Figure 1
Add: 1F, No.3, Industrial East 9 Measurement before device stabilization. Road,
th
Error 5~9, the system is not functioning properly.
2. Insert the new AAA *2 pcs batteries. (See Figure 2)
Science-Based Industrial Park, HsinChu, Taiwan 300.
Battery replacement
(1) In forehead mode: Temperature taken is higher than 108°F (+42.2
Trouble shooting:
3. Replace the battery cover. (See Figure 3)
Device cannot be powered on to the ready stage.
The ambient temperature is not within the range between 50
Measurement before device stabilization.
(2) In surface mode: Temperature taken is higher than 176°F (+80
The ambient temperature is not within the range
Error Message
(1) In forehead mode: Temperature taken is lower than 93.2°F (+34
(1) In forehead mode: Temperature taken is higher than 108°F (+42.2
between 50˚F~104˚F (10˚C~40˚C).
The ambient temperature is not within the range between 50
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
(2) Error 5~9, the system is not functioning properly. In surface mode: Temperature taken is higher than 176°F (+80
Figure 1
(1) In forehead mode: Temperature taken is lower than 93.2°F (+34
(1) In forehead mode: Temperature taken is higher than 108°F (+42.2
Device cannot be powered on to the ready stage.
Measurement before device stabilization.
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
Trouble shooting:
(2) In surface mode: Temperature taken is higher than 176°F (+80
Figure 1
(1) In forehead mode: Temperature taken is lower than 93.2°F (+34
Error Message
(1) In forehead mode: temperature taken is higher
Device cannot be powered on to the ready stage. The ambient temperature is not within the range between 50
Warranty:
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
Error 5~9, the system is not functioning properly. than 108˚F (42.2˚C)
Trouble shooting:
Warranty: 12 months
(1) In forehead mode: Temperature taken is higher than 108°F (+42.2
Device cannot be powered on to the ready stage.
Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.) Error Message
Warranty:
(2) (2) In surface mode: temperature taken is higher In surface mode: Temperature taken is higher than 176°F (+80
Measurement before device stabilization.
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture
Warranty: 12 months (1) In forehead mode: Temperature taken is lower than 93.2°F (+34
Error 5~9, the system is not functioning properly.
than 176˚F (80˚C)
month, the others is the serial number.
Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.) (2) In surface mode: Temperature taken is lower than –7.6°F (-22
Warranty:
The ambient temperature is not within the range between 50
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture
Warranty: 12 months Measurement before device stabilization.
(1) In forehead mode: Temperature taken is higher than 108°F (+42.2
events at any time, please contact the dealers or nearest service address. (1) In forehead mode: temperature taken is lower
Device cannot be powered on to the ready stage.
month, the others is the serial number.
Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.)
(2) In surface mode: Temperature taken is higher than 176°F (+80
Warning: No modification of this equipment is allowed.
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected
The ambient temperature is not within the range between 50
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture
than 93.2˚F (+34˚C)
(1) In forehead mode: Temperature taken is lower than 93.2°F (+34
events at any time, please contact the dealers or nearest service address.
Warranty: month, the others is the serial number.
Please read the instructions for use
(1) In forehead mode: Temperature taken is higher than 108°F (+42.2
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
Road, (2) In surface mode: temperature taken is lower
th
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected Warning: No modification of this equipment is allowed.
Warranty: 12 months
(2) In surface mode: Temperature taken is higher than 176°F (+80
Radiant Innovation Inc.
events at any time, please contact the dealers or nearest service address.
Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.) than -7.6˚F (-22˚C)
Device cannot be powered on to the ready stage. (1) In forehead mode: Temperature taken is lower than 93.2°F (+34
Please read the instructions for use
Http://www.radiantek.com.tw
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture Warning: No modification of this equipment is allowed.
(2) In surface mode: Temperature taken is lower than –7.6°F (-22
Add: 1F, No.3, Industrial East 9 Road,
th
Radiant Innovation Inc.
month, the others is the serial number.
Device cannot be powered on to the ready stage. Change with a new battery.
Science-Based Industrial Park, HsinChu, Taiwan 300. Please read the instructions for use
Warranty:
Http://www.radiantek.com.tw
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected
Device cannot be powered on to the ready stage.
Add: 1F, No.3, Industrial East 9 Warranty: 12 months Road,
th
Radiant Innovation Inc.
events at any time, please contact the dealers or nearest service address.
Science-Based Industrial Park, HsinChu, Taiwan 300. Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.)
Http://www.radiantek.com.tw
Warning: No modification of this equipment is allowed.
Warranty:
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture
Add: 1F, No.3, Industrial East 9 Road,
th
Warranty: 12 months
Please read the instructions for use
month, the others is the serial number.
Science-Based Industrial Park, HsinChu, Taiwan 300.
Manufacture Date: as the serial number (please open the battery cover, it is shown on the inside of the device.)
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected
Radiant Innovation Inc.
Ex.SN:E512A000001, the first "E" is External, the second number "5" is the last number of manufacture year, the third and the fourth number "12" is the manufacture
events at any time, please contact the dealers or nearest service address.
Http://www.radiantek.com.tw
month, the others is the serial number.
Warning: No modification of this equipment is allowed.
Add: 1F, No.3, Industrial East 9 Road,
th
Note: The thermometer is calibrated at the time of manufacture. If you question calibration mode, the accuracy of temperature measurements or unexpected
Science-Based Industrial Park, HsinChu, Taiwan 300.
Please read the instructions for use
events at any time, please contact the dealers or nearest service address.
Warning: No modification of this equipment is allowed.
Radiant Innovation Inc.
Http://www.radiantek.com.tw
Please read the instructions for use
Add: 1F, No.3, Industrial East 9 Road,
4 th
Radiant Innovation Inc.
Science-Based Industrial Park, HsinChu, Taiwan 300.
Http://www.radiantek.com.tw
(-1.4 ~ -1.7 ° C).
(0.20 ° C)
(-1.4 ~ -1.7 ° C).
(0.20 ° C)
(-1.4 ~ -1.7 ° C).
(0.20 ° C)
(-1.4 ~ -1.7 ° C).
(0.20 ° C)
(-1.4 ~ -1.7 ° C).
Figure 2
(0.20 ° C)
(-1.4 ~ -1.7 ° C).
Problem
(0.20 ° C)
Figure 2
Problem
Figure 2
Figure 2
Problem
o F~104
Figure 2
BF type applied part
Problem
Problem
Figure 2
Ref No.：032020
Problem
Figure 2
Figure 2
Problem
Problem
BF type applied part
BF type applied part
Ref No.：032020
BF type applied part
BF type applied part
Ref No.：032020
Ref No.：032020
BF type applied part
Ref No.：032020
BF type applied part Ref No.：032020
BF type applied part
Ref No.：032020
icon on the screen
Figure 3
Unload the battery, wait for 1 minute and repower it. If the message
reappears, contact the retailer for service.
Wait for "Er1" to disappear.
Allow the thermometer to rest in a room for at least 15 minutes at room
o F~104 o F (10 o C~40 o C).
temperature: 50
o C)
o C)
Please select the target within specifications. If a malfunction still exists,
please contact the nearest retailer.
o C)
o C)
Change with a new battery.
Figure 3
Unload the battery, wait for 1 minute and repower it. If the message
reappears, contact the retailer for service.
Figure 3
Solution
Wait for "Er1" to disappear.
Figure 3
Allow the thermometer to rest in a room for at least 15 minutes at room
o F (10 o C~40 o C).
temperature: 50 Unload the battery, wait for 1 minute and repower it. If the message
Figure 3
repower. If the message reappears, contact the
reappears, contact the retailer for service.
o C)
service department.
o C) Please select the target within specifications. If a malfunction still exists,
Unload the battery, wait for 1 minute and repower it. If the message
Wait for "Er1" to disappear.
reappears, contact the retailer for service.
please contact the nearest retailer.
o C)
Allow the thermometer to rest in a room for at least 15 minutes at room
Wait for "Er1" to disappear.
o F~104 o F (10 o C~40 o C).
o C)
Unload the battery, wait for 1 minute and repower it. If the message
Figure 3
Wait for "Er1" to disappear.
temperature: 50
reappears, contact the retailer for service.
o C)
Allow the thermometer to rest in a room for at least 15 minutes at room
Change with a new battery.
o F~104 o F (10 o C~40 o C).
Wait for "Er1" to disappear.
o C) Please select the target within specifications. If a malfunction still exists,
temperature: 50 Allow the thermometer to rest in a room for
please contact the nearest retailer.
o C)
o C)
Allow the thermometer to rest in a room for at least 15 minutes at room
at least 15 minutes at room temperature:
Unload the battery, wait for 1 minute and repower it. If the message
o F~104 o F (10 o C~40 o C).
o C)
o C) Please select the target within specifications. If a malfunction still exists,
temperature: 50
Figure 3
reappears, contact the retailer for service.
please contact the nearest retailer.
o C) 50˚F~104˚F (10˚C~40˚C).
o C)
Change with a new battery.
Wait for "Er1" to disappear.
o C)
o C) Please select the target within specifications. If a malfunction still exists,
please contact the nearest retailer.
Figure 3
o C)
Allow the thermometer to rest in a room for at least 15 minutes at room
o F~104 o F (10 o C~40 o C). Change with a new battery.
o C)
temperature: 50
Unload the battery, wait for 1 minute and repower it. If the message
reappears, contact the retailer for service.
o C)
Change with a new battery.
o C) Please select the target within specifications. If a malfunction still exists,
Wait for "Er1" to disappear.
please contact the nearest retailer. Unload the battery, wait for 1 minute and repower it. If the message
o C)
Please select the target within specifications. If a
Allow the thermometer to rest in a room for at least 15 minutes at room
reappears, contact the retailer for service.
o C)
o F~104 o F (10 o C~40 o C).
malfunction still exists, please contact the service
temperature: 50
Wait for "Er1" to disappear.
o C)
Change with a new battery.
department.
Allow the thermometer to rest in a room for at least 15 minutes at room
o C) Please select the target within specifications. If a malfunction still exists,
o F~104 o F (10 o C~40 o C).
temperature: 50
please contact the nearest retailer.
o C)
o C)
o C)
o C) Please select the target within specifications. If a malfunction still exists,
please contact the nearest retailer.
o C) Change with a new battery.
o C)
Change with a new battery.
www.mastercool.com
icon on the screen
icon on the screen
icon on your LCD
icon on the screen
icon on the screen
icon on the screen
icon on the screen
Solution
o F~104 o F (10 o C~40 o C).
Solution
Solution
o F~104 o F (10 o C~40 o C).
Solution
Solution
o F~104 o F (10 o C~40 o C).
o F~104 o F (10 o C~40 o C).
Solution
o F~104 o F (10 o C~40 o C).
Solution
o F~104 o F (10 o C~40 o C).
Solution
o F~104 o F (10 o C~40 o C).
o F~104 o F (10 o C~40 o C).
icon on your LCD
Figure 2
Figure 2
Figure 2
Figure 2
Figure 2
icon on your LCD
icon on your LCD
Figure 2
icon on your LCD
Figure 2
icon on your LCD
icon on your LCD
icon on your LCD