Failure to comply with this warning can result in warranty obligation unless each product is registered personal injury or death, damage to the within 10 days of retail purchase, using the Landoll implement or its components and inferior Company, LLC Ag Products on-line registration process. operation.
INTRODUCTION AND SAFETY INFORMATION Safety When applying decals to the implement, be sure to clean the surface to remove any dirt or residue. Where possible, sign placement should protect the sign from NOTE abrasion, damage, or obstruction from mud, dirt, oil etc. Investigation has shown that nearly 1/3 of all farm accidents are caused by careless use of machinery.
INTRODUCTION AND SAFETY INFORMATION Attaching, Detaching and Storage 2. When removing and installing wheels use wheel-handling equipment adequate for the weight 1. Do not stand between the tractor and implement involved. when attaching or detaching implement unless both are not moving. Chemical Safety 2.
INTRODUCTION AND SAFETY INFORMATION Safety Chain 1. Use a safety chain to help control drawn machinery should it separate from the tractor drawbar. 2. Use a chain with a strength rating equal to or greater than the gross weight of towed machinery, in accordance with ASAE S338.2 specifications.
Chapter 2 Assembly IMPORTANT CAUTION All harnesses must be firmly attached to machine frame members, or nylon tubing, so they don’t sag or Do not work on or under this machine unless become torn loose by field debris. Use the tie straps securely blocked and supported by a hoist or provided.
ASSEMBLY Drawbar Installation 2. Install Toolbox to Drawbar cross member using two 3/8-16 x 1 Bolts, Flat Washers and Flanged Locknuts. WARNING 3. Attach Air Manifold Assembly to the Drawbar cross member using one 5/8-11 x 1-3/4 Bolt, Flat Washer Do not attempt to lift heavy parts manually.
ASSEMBLY Wheel Arm Installation 4. Install 3 x 8 Hydraulic Cylinder to the Wheel Arm Bracket, by sliding a 1 x 2 11ga SS Washer over 1 x 1. Position Wheel Arm Assembly into the Wheel Arm 8-3/4 Pin and insert into Wheel Arm Bracket and Bracket.
ASSEMBLY 3Pt Hitch Installation 2. Attach the Air Manifold Bracket Assembly to the 3Pt Hitch using two 3/8 x 16 x 5-1/4 Bolts, and Flanged 1. Attach the 3Pt Hitch to the Seeder Frame with 3/4-10 Locknuts. Do Not tighten until harnesses are U-Bolts, Flat Washers and Locknuts.
Page 19
ASSEMBLY 5. Attach the Manual Holder to the 3Pt Hitch using two 7. Place the Calibration Crank and Wrenches in the 1/4-20 x 1 Bolts, Flat Washers and Locknuts. Toolbox. See Figure 2-4. 6. Attach the Connector Holder to the Air Manifold Bracket Assembly using two 1/4-20 x 3/4 Bolts, Flat Washers and Locknuts.
ASSEMBLY Drawbar Air System Installation 4. Cut off any excess nylon tubing and insert ends into the Air Manifold Assembly Push to Connect Elbows. 1. Cut the nylon tubing into two equal lengths, Cut ends of Nylon Tubing should be smooth and burr approximately 15ft each.
ASSEMBLY 3Pt Hitch Air System Installation 4. Cut off any excess nylon tubing and insert nylon tubing ends into the Push to Connect male elbows 1. Cut the nylon tubing into two equal lengths, located on the Air Manifold Assembly. Cut ends of approximately 15ft each.
ASSEMBLY Hydraulic Lift Circuit 5. Attach a 3/8 x 53 Hose to each Cylinder Base End Elbow Restrictor and a 3/8 x 64 Hose to each 1. Install the SMV Bracket to the Frame Bracket with Cylinder Rod End Elbow. 5/16-18 x 1 Bolts, Flat Washers and Locknuts.
ASSEMBLY Drawbar Model LED Warning Lamps IMPORTANT Installation All harnesses must be firmly attached to machine 1. Amber Lamps are assembled to frame frame members, or nylon tubing, so they don’t sag or ends/extremity of machine. Unscrew Amber Lamp become torn loose by field debris. Use the tie straps Jam Nut if not already removed from Lamp Stud so provided.
ASSEMBLY 3Pt Hitch Model LED Warning Lamps IMPORTANT Installatio All harnesses must be firmly attached to machine 1. Unscrew Amber Lamp Jam Nut if not already frame members, or nylon tubing, so they don’t sag or removed from Lamp Stud so that the Nut and become torn loose by field debris.
ASSEMBLY Acre Meter Installation - Optional The acre meter consists of three main parts: the Acre Meter, the Pick-up Switch and the Magnet Wheel Assembly. 1. Attach the Acre Meter Angle to the end transmission using two 5/16-18 x 1 Bolts, Lock Washers and Nuts. See Figure 2-12.
ASSEMBLY Clutch Installation - Optional 4. Secure Clutch Torque Arm to the Clutch Transmission Tab with 1/4-20 x 1 Bolt, Spacer, Flat If not equipped contact dealer to order. Washer, and Locknut. Clutch Arm must be free to 1. Install Flangettes and Bearings onto Clutch float 1/16 of an inch.
ASSEMBLY Clutch and Seed Shaft Sensor 2. Connect either 4 ft (3Pt) or 20 ft (Drawbar) Extension Harness to the Clutch Harness. Route along 3Pt Electrical Layout - Optional Hitch or Drawbar towards front of machine. See Figure 2-15. The clutch is controlled by a toggle switch on the Console.
ASSEMBLY Clutch and Seed Shaft Sensor 4. Plug Clutch and Seed Shaft Sensor Console 3 Pin Power Cable into the Tractor Convenience Outlet Console Tractor Installation - and 9 Pin Cable into the 4ft or 20ft Extension Optional Harness. 5. Check clutch operation: Clutch will engage when 1.
ASSEMBLY Load Cell Installation - Optional 6. Carefully lower the Seedbox ensuring the cutout on the Seedbox goes over the Load Cell Cable. 7. Secure Seedbox to each Load Cell with two 3/4-10 x CAUTION 2 Bolts and Lock Washers. Do not work on or under this machine unless securely blocked and supported by a hoist or tractor or by other sufficient means.
ASSEMBLY Clutch and Seed Shaft Sensor 6. Tilt the GT400 Scale Indicator to latch the top of the GT400 Indicator Bracket. Secure bottom with 1/4-20 Console w/Scale Indicator Tractor x 1/2 Bolts and Spiral Flanged Locknuts. Installation - Optional 7. Plug the Power and Indicator Cables into the bottom of GT400 Scale Indicator.
Page 37
ASSEMBLY Table provided for general use. NOTES: F-1021-0719 2-23...
ASSEMBLY CAUTION Do not work on or under this machine unless securely blocked and supported by a hoist or tractor or by other sufficient means. Coil Tine Harrow Installation - Optional 1. Attach the two Harrow Mounting Brackets to the Frame Tube with 3/4-10 U-Bolts, Flat Washers and Locknuts.
Page 40
ASSEMBLY CAUTION Do not work on or under this machine unless securely blocked and supported by a hoist or tractor or by other sufficient means. S-Tine Harrow Installation - Optional 1. Attach the two Harrow Mounting Brackets to the Frame Tube with 3/4-10 U-Bolts, Flat Washers, and Locknuts.
Failure to take preventive measures against This chapter covers the basic operation and usage accidental lowering can result in serious procedures for the Landoll/Brillion Sure Stand Seeder. personal injury. Be sure to read and understand the Safety Procedures and Cautions starting on page 1-2.
OPERATION Tractor Preparation/Attaching of 3Pt • Make sure the tractor receptacle cover latches over the keyway on the 7 Pin Connector to hold the Hitch Seeder Connector in place. 1. The Seeder is designed to be used with Free Link •...
Page 45
OPERATION Figure 3-1: 3 Point Hitch F-1021-0719...
OPERATION Attaching/Detaching 3Pt Hitch Seeder WARNING To prevent the implement from tipping forward on the frame, disengage parking stand only when the seeder is fully attached to the tractor. Be sure to observe the following sequences. Hooking Up the Seeder: 1.
OPERATION Tractor Preparation/Attaching of 6. Attach safety chain to tractor allowing plenty of movement for turning both directions. The safety Pull Type Seeder chain should latch securely to prevent it coming loose. See Figures 3-6 and 3-7. 1. The Seeder is designed to be used with a CAT 2 or CAT 3 Drawbar Hitch.
OPERATION Attaching/Detaching Pull Type Seeder Attaching the Seeder for Field Operations: Seeder parked lowered 1. Attach Seeder to the Tractor. 2. Raise the Seeder fully to extend the Hydraulic Lift Cylinders and rotate the Transport Locks in the engaged position over the Cylinder Rod. Secure with the Clevis Pins and Hairpin Cotters.
OPERATION 1. If the hydraulic system is not filled with oil it should be purged of air before transporting and field operations. Carefully hitch the Seeder to the tractor and connect the hydraulic lift hoses. 2. Remove the Transport Locks. See Figure 3-8. 3.
OPERATION Seed Rate Adjustment IMPORTANT The Clutch if equipped must be disengaged (power WARNING off) when Seed Shafts are turned manually for Calibration. • To prevent damage to the seed meters, Do If Seeder is not equipped with a Clutch, remove not apply excessive force to the adjusting Chain from Speed Reducer to Transmission Shaft.
Front Roller. See Figure 3-14. Figure 3-15: Calibration Figure 3-14: No Clutch Disengagement Landoll assumes no liability pertaining to Seeding Rates achieved with this Seeder. Rates listed are general in nature and should be used as starting points only. Seed varieties and blends listed represent those calibrated through in-house test meters.
OPERATION Clutch Operation - Optional Electronic Acre Meter Kit - Optional The clutch is controlled by a toggle switch on the Console. See Figure 2-16. IMPORTANT Clutch characteristics are as follows: 1. The clutch is engaged when power (12 volts) is Acre Meter is dust and splash resistant, under no applied.
Page 54
OPERATION 1. If you know the number, select it using the UP and If the password is not correct, you will not be able to DOWN buttons. When you press the /FUNC change the acre counter settings. When the “PASS” button, the Acre Counter will accept the number in function is selected again, “Ent”...
OPERATION Coil Tine Harrow - Optional 1. The S-Tine Harrow depth may be adjusted for a deeper more aggressive depth or shallower for The Seeder has a Optional Coil Tine Harrow to remove minimal disturbance. tire tracks before the rollers compact the soil.The coils 2.
OPERATION General Operation DANGER 1. The minimum horsepower requirements are typically Stay away from power lines when transporting, 6-8 horsepower per foot. This will vary widely due to extending implement. Electrocution can occur speed, depth, moisture, and types of soils. Local without direct contact.
Page 58
OPERATION Table provided for general use. NOTES: 3-16 F-1021-0719...
Chapter 4 Maintenance General Torque Specifications (rev. 4/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They Do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.
MAINTENANCE Hydraulic Fitting Torque Specifications 37 degree JIC, ORS, &ORB (REV. 10/97 This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They Do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.
MAINTENANCE Tires 7. Slide the Inner Bearing Cone and Hub onto the Spindle. Recommended Tire Size: 11L x 15, 12Ply Implement 8. Install the Outer Bearing Cone, Washer and Slotted Rib Rating Nut. Tire Inflation Pressure: 52 PSI 9. Tighten the Slotted Nut while rotating the Hub until When Re-Installing the 9/16-18 Wheel Nuts tighten to 50 there is a slight resistance to wheel rotation.
Seal kits are available from your Landoll dealer. 3. Check all hydraulic hoses weekly. Look for binding or cracking. Replace all worn or defective parts immediately.
MAINTENANCE Roller Axle Assembly After an initial run of 5-10 hours, check the Roller Axle Assemblies to ensure that the wheels are tight to one another. If not slide the Rear Roller Wheels tight together and adjust the Axle Clamps. Front Roller push wheels against welded Roller End Plate and adjust the Axle Clamp.
MAINTENANCE Seed Meter Adjustment 2. There are 4 sections of Seed Meters grouped together. On each end of each section there are 3/8 Square Bore Collars with Set Screws. Loosen Collar IMPORTANT Set Screws to move that particular section as The Clutch if equipped must be disengaged (power needed.
MAINTENANCE Servicing Seedshaft Assembly LED Warning Lamps When plugging in the LED 7 Pin Warning Lamp IMPORTANT Connector: The Clutch if equipped must be disengaged (power 1. Make sure the tractor has a good clean receptacle, off) when Seed Shafts are turned manually. free of dirt and corrosion.
MAINTENANCE Acre Meter Troubleshooting 4. If step 3 works then wave a magnet in front of the Pick-up Switch face with it re-connected to the display and see if the display increments up. If not, IMPORTANT put an ohm meter or continuity tester on the contacts Acre Meter is dust and splash resistant, under no of the Pick-up Switch harness and place a magnet in circumstances should this unit be submerged in any...
Chapter 5 General Reference and Specifications Figure 5-1: Model Specifications F-1021-0719...
Page 68
GENERAL REFERENCE AND SPECIFICATIONS Table provided for general use. NOTES: F-1021-0719...
Page 69
Document Control Revision Log: Date Revision Improvement(s) Description and Comments 07/2019 0719 Initial Release...
Page 70
Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Sure Stand Seeder Models SS16 and SSP16 Operator’s Manual Re-Order Part Number F-1021 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...