Related Manuals for Landoll Brillion Turfmaker II Series
Summary of Contents for Landoll Brillion Turfmaker II Series
- Page 1 ‘ Turfmaker II Models SL2081/SL2101/SL2121 SLP2081/SLP2101/SLP2121 SLB2081/SLB2101/SLB2121 SLPB2081/SLPB2101/SLPB2121 Operator’s Manual LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM 9K998-2306...
- Page 2 Manuals for Turfmaker II, Models SL2081/SL2101/SL2121, SLP2081/SLP2101/SLP2121, SLB2081/SLB2101/SLB2121 and SLPB2081/SLPB2101/SLPB2121 Manual Number Manual Type 9K998 Operator’s Manual 9K997 Parts Manual...
- Page 3 DANGER DO NOT operate or perform any maintenance tasks on this equipment until you have completed the following: 1. Receive proper training to operate this equipment safely. 2. Read and understand the operator’s manual. 3. Be thoroughly trained on inspection and repair procedures. Failure to comply with this warning may result in serious injury or possibly death.
- Page 5 Table of Contents Safety Information Introduction ........... . 1-1 Description of Unit .
- Page 6 TABLE OF CONTENTS Console w/Clutch Control Installation - Optional ..... . 2-24 Console w/Clutch Control - Seed Shaft Sensor - Optional ....2-25 Console w/Clutch Control Tractor Installation - Optional .
- Page 7 TABLE OF CONTENTS Speed (Simulated Speed)........4-3 Speed Calibration .
- Page 8 TABLE OF CONTENTS Electric Clutch..........5-11 Acre Meter Troubleshooting .
- Page 9 10 days of retail purchase, using the Landoll injury or death, damage to the machine or its Company, LLC Ag Products on-line registration process.
- Page 10 TABLE OF CONTENTS Safety • When applying decals to the implement, be sure to clean the surface to remove any dirt or residue. Where possible, sign placement should protect the sign from NOTE abrasion, damage, or obstruction from mud, dirt, oil etc. Investigation has shown that nearly 1/3 of all farm DANGER accidents are caused by careless use of machinery.
- Page 11 TABLE OF CONTENTS Transporting Safety Attaching, Detaching and Storage • Do not stand between the tractor and machine when IMPORTANT attaching or detaching machine unless both are not It is the responsibility of the owner/operator to moving. comply with all state and local laws. •...
- Page 12 TABLE OF CONTENTS Tire Safety Safety Chain Tire changing can be dangerous and should be performed 1. Use the Safety Chain to help control drawn machinery by trained personnel using correct tools and equipment. should it separate from the Tractor Drawbar. •...
- Page 13 5K395 224188 - (Rear) Seed Chart (After 01/2020) ITEM 13 ITEM 15 5K285 - (Rear) Seed Chart (Before 01/2020) 2P151 5K395 CAUTION Landoll Company, LLC Marysville, Kansas ITEM 20 www.landoll.com BE SURE TO ENGAGE LANDSCAPE 9J429 SEEDER PARKING PIN ON LEFT END OF...
- Page 14 TABLE OF CONTENTS SL2 HitchDecals Figure 1-4: Decal Placement - Hitch 9K998-2306...
- Page 15 TABLE OF CONTENTS Figure 1-5: Decal Placement - Single Box, 8FT and 10FT 9K998-2306...
- Page 16 TABLE OF CONTENTS Figure 1-6: Decal Placement - Single Box, 12FT 9K998-2306...
- Page 17 TABLE OF CONTENTS 8FT AND 10FT SEEDER SL2 DecalsDoubleBox 12FT SEEDER Figure 1-7: Decal Placement - Double Box 9K998-2306...
- Page 18 TABLE OF CONTENTS Table provided for general use. NOTES: 1-10 9K998-2306...
- Page 19 Chapter 2 TABLE OF CONTENTS Assembly IMPORTANT CAUTION All harnesses must be firmly attached to machine Do not work on or under this machine unless frame members, so they don’t sag or become torn securely blocked and supported by a hoist or loose by field debris.
- Page 20 TABLE OF CONTENTS 3-PT Hitch Seeder Assembly CAUTION When shipped, seeder comes assembled except for Do not disengage pin unless seeder is fully Lights and 3-PT Hitch. attached to a tractor. Seeder may be rear-heavy 1. Support Seeder Assembly with a hoist or by similar and tip backward on frame.
- Page 21 TABLE OF CONTENTS Frame Locknut,5/8-11 Lock Washer,5/8 Hose Clamp Manual Holder U-Bolt,5/8-11 SL2 Op3PtHitch 3-PT Hitch Figure 2-4: 3-PT Hitch 9K998-2306...
- Page 22 TABLE OF CONTENTS Pull Type Seeder Assembly SMV Support When shipped, Seeder comes assembled except for Lights, Hub and Spindle Assemblies, Tire and Wheels Assemblies and Drawbar. Seed Box 8FT and 10FT Assembly 1. Untie the two rolled up Drawbar Hydraulic Hoses near the center of the Frame Tube.
- Page 23 TABLE OF CONTENTS U-Bolt,5/8-11 Nut,5/8-11 Lock Washer,5/8 Manual Holder Hose Clamp Hose Holder Drawbar Bolt,5/8-11 x 1-1/2 Lock Washer,5/8 Nut,5/8-11 Figure 2-6: 8FT and 10FT Drawbar U-Bolt,1/2-13 Nut,5/8-11 Lock Washer,5/8 Flat Washer,1/2 U-Bolt,5/8-11 Locknut,1/2-13 RH Brace Hose Clamp Manual Holder Hose Holder Drawbar Bolt,5/8-11 x 1-1/2...
- Page 24 TABLE OF CONTENTS Tire and Wheel Installation WARNING Use a torque wrench to assure proper torque. Insufficient torque can cause stud breakage and damage the wheel pilots. Over torque can stress the Bolts and strip the threads. NOTE All tire/wheel assemblies are mounted with the valve stem facing outward from Hub and Spindle.
- Page 25 TABLE OF CONTENTS Hydraulic Installation Hydraulic Assembly 1. Restrictors installed in Cylinder Ports, connect 45 WARNING Degree Fitting so they are free to swivel. Connect top Hydraulic Hose to the Cylinder Base and bottom Hydraulic Hose to the Cylinder Rod End. Position the Escaping fluid under pressure can be nearly Hydraulic Hoses so that the Cylinder Base End points invisible and have enough force to penetrate the...
- Page 26 TABLE OF CONTENTS Hose Clamp Frame Pair Hose Assembly Bolt,1/4-20 x 1-1/2 Top Plate Op SeederHyd Drawbar Figure 2-12: 8FT and 10FT Drawbar Hydraulics Frame Hose Clamp Pair Hose Assembly Bolt,1/4-20 x 1-1/2 Top Plate Drawbar Op SeederHyd12ft Figure 2-13: 12FT Drawbar Hydraulics 9K998-2306...
- Page 27 TABLE OF CONTENTS Purge the Hydraulic Lift System Bolt,5/8-11 Flat Washer,5/8 The Hydraulic system is not filled with oil and should be purged of air before transporting and field operations. Locknut,5/8-11 Lift Circuit approximate oil requirement: 0.4 gallons. 1. Carefully Hitch the Seeder to the Tractor and connect the Hydraulic Lift Hoses.
- Page 28 TABLE OF CONTENTS Warning Lamp Installation, IMPORTANT 8FT and 10FT All Harnesses must be firmly attached to Machine Frame members or Hydraulic Hoses so they do not sag or become torn loose by field debris. NOTE 8. Attach the SMV sign to the SMV Support with 5/16-18 10FT Drawbar model is shown, 10FT 3-PT, 8FT Drawbar x 1"...
- Page 29 TABLE OF CONTENTS Amber Lamp Light Bracket Bolt,1/4-20 x 1-1/4 Locknut,1/4-20 Red Lamp Tie Wrap Support Bolt,5/16-18 x 1 Flat Washer,5/16 Connector Locknut, Holder 5/16-18 Bolt, 1/4-20 x 1 Flat Washer,1/4 Locknut,1/4-20 Lamp Harness 7-Pin Harness Light Bracket Locknut, 1/4-20 Bolt,1/4-20 Adhesive x 1-1/4...
- Page 30 TABLE OF CONTENTS Warning Lamp Installation, IMPORTANT 12FT All Harnesses must be firmly attached to Machine Frame members or Hydraulic Hoses so they do not sag or become torn loose by field debris. NOTE 8. Attach the SMV sign to the SMV Mount located on the 12FT 3-PT model is shown, Drawbar model similar.
- Page 31 TABLE OF CONTENTS Amber Lamp Bolt,1/4-20 Bolt,1/4-20 x 1-1/4 x 1-1/4 Red Lamp Flat Washer, 5/16 Bolt, 5/16-18 x 1 Tie Wrap Light Locknut, 5/16-18 Locknut, 1/4-20 7-Pin Harness Light Bar Connector Holder Lamp Harness Bolt, 1/4-20 x 1 Flat Washer,1/4 Locknut,1/4-20 Locknut,1/4-20 7-Pin Harness...
- Page 32 TABLE OF CONTENTS Latch Installation Cover Gas Spring Installation Large Seed Box Cover with Latches and Gas Springs NOTE 1. Place the gasket on latch base and place on Seed Gas Spring rod end must be down for proper Box Cover. functionality.
- Page 33 TABLE OF CONTENTS Electric Clutch Kit - Optional Mini Monitor, 3-Pin Power Plug to 12 Volt Tractor Convenience Outlet and 6-Pin Connector to the 240" Extension Harness. 4-Pin Connector is not used at IMPORTANT this time. Connect 240" Extension Harness to Seeder At no time use high pressure water or air to clean the Harness.
- Page 34 TABLE OF CONTENTS Acre Meter Kit, 5K275 - Optional Magnet Wheel Assembly Clutch Shaft Not Used with Brillion Elite Mini Monitor NOTE 1/8" Max The Acre Meter Kit consists of three main parts, the Acre Meter, the Pick-Up Switch and the Magnet Wheel Assembly.
- Page 35 TABLE OF CONTENTS Nut,3/8-16 Seed Box Lock Washer,3/8 Flat Washer,3/8 Acre Meter Acre Meter Assembly Mount Bolt,3/8-16 x 1 Extension Harness Transmission Clutch Bracket Adhesive Screw,#8-32 x 1-1/4 Mounting Plate Flat Washer,#8 Tie Wrap Magnet Wheel Assembly Screw,#6-32 x 1/2 Clutch Shaft Screw,#10-24 x 3/4 Pick-Up...
- Page 36 TABLE OF CONTENTS Brillion Elite Mini Monitor - Shaft. See Figure 2-29. Connect the Smart Seed Shaft Sensor to the Seeder Harness. Optional Pick-Up Switch Smart Shaft The Brillion Elite Mini Monitor System by Loup Bracket Sensor utilizes a MUX communication line. Sensors must be Transmission learned into the Monitor.
- Page 37 TABLE OF CONTENTS Connector outside the Seed Box, feed the terminals 8. Connect the 240" Extension Harness to the Seeder through the Cord Grip. Install the terminals into the Harness. Route the 240" Extension Harness along 3-Pin Shroud labeled “A”, “B” and “C” as follows “A” the Seeder Frame and down the Drawbar/3-PT Hitch White, “B”...
- Page 38 TABLE OF CONTENTS Brillion Elite Mini Monitor Electrical Schematic - Single Seed Box Brillion Elite Mini Monitor 4-Pin Radar/GPS Plug Monitor Mount Elite Mini Tractor Bin Level Harness Smart Shaft Sensor #2 3-Pin Power Plug Sensor #1 6-Pin Connection 14-Pin Connector Smart Clutch Relay...
- Page 39 TABLE OF CONTENTS Brillion Elite Mini Monitor - Ground Speed Sensor Smart Shaft Sensor Transmission Screw,Rnd Hd #8-32 x 1-1/4 Bearing Flangette Washer,Flat #8 Quill Shaft Input Shaft Clutch Bolt,1/2-13 x 1-1/4 Nut,1/2-13 Locknut, Flange #8-32 Washer, Actuator Lock 1/2 Pick-Up Assembly Set Screw,...
- Page 40 TABLE OF CONTENTS Brillion Elite Mini Monitor - Rear Seed Box Seed Shaft Sensor Seed Shaft,3/8 Square Screw,Rnd Hd, 1/4-20 X 3/4 Sensor Mount, 4.25 Spacing Screw,Rnd Hd Washer, #8-32 x 1-1/4 Flat 1/4 Locknut, Washer, Washer,Flat #8 Flange#8-32 Lock 1/4 Smart Nut,1/4-20 Shaft Sensor...
- Page 41 TABLE OF CONTENTS Brillion Elite Mini Monitor 4. Attach the Monitor Mount to the Straight Bracket with #10-24 x 1 Machine Screws, Flat Washers, Lock Tractor Installation - Optional Washers, and Nuts, provided with Monitor Mount. 5. With the Brillion Elite Mini Tractor Harness, plug the 1.
- Page 42 TABLE OF CONTENTS Console w/Clutch Control 6. Route Seeder Harness along Frame of Seeder. Ensure plug labeled Electric Clutch Power is on the Installation - Optional left side. 7. On left side connect plug labeled “Electric Clutch 1. If equipped with Clutch Switch Bar, remove from Power”...
- Page 43 TABLE OF CONTENTS Console w/Clutch Control - 8. Position Seed Shaft Sensor so it is 1/8" from the Magnet Wheel Assembly. See Figure 2-39. Tighten Seed Shaft Sensor - Optional both Seed Shaft Sensor Retaining Nuts. Seed Shaft Sensor and Magnet Wheel Assembly Shaft Sensor Installation Bracket...
- Page 44 TABLE OF CONTENTS Console w/Clutch Control 4. Plug Console 3-Pin Power Cord into the Tractor Convenience Outlet and 9-Pin Cord into the Seeder Tractor Installation - Optional Harness. 5. Check clutch operation: Clutch will disengage when 1. Mount Angle Bracket onto Tractor where convenient power is applied.
- Page 45 TABLE OF CONTENTS Table provided for general use. NOTES: 9K998-2306 2-27...
- Page 46 TABLE OF CONTENTS Rear Seed Box Installation - 7. Remove Seed Rate Adjuster Bearing Carrier Plate with Bearing still assembled to it, from the Seed Box Optional (After 01/2020) RH Support and Seed Rate Adjusting Screw. 8. At the center of the Seeder where the RH and LH Hex 1.
- Page 47 TABLE OF CONTENTS 11. Remove the Mount Plate Hardware and slide the LH Seed Box far enough to the right to remove the Mount Transmission Plate from the Seed Box and Transmission. Complete Shield removal of the Seed Box is not required, the Seed Shaft will slide in the 37 Tooth Sprocket and Bearing.
- Page 48 TABLE OF CONTENTS 15. Install 5/8-11 x 1 Bolt into Drive Tube Threaded End. 20. While supporting the RH Front Seed Box, position Slide Square Bore End of Drive Tube, towards the Seed Box against Double Box Center Bracket. Seed Box, through the 3/4" Bearings while installing Assemble Seed Boxes and Center Bracket together 23 Tooth Sprocket and secure Sprocket to Drive Tube with Hardware but do not tighten at this time.
- Page 49 TABLE OF CONTENTS 30. Assemble onto the Rear Seed Box Seed Shaft the 31. Adjust Front and Rear Seed Box Seed Meters so that Seed Rate Adjusting Screw, 1-8 Nut, Bearing, Seed all the Seed Meters are closed. Perform Seed Meter Rate Adjusting Nut and 1/2-13 Locknut.
- Page 50 TABLE OF CONTENTS Rear Seed Box Installation - 7. Remove Seed Rate Adjuster Bearing Carrier Plate with Bearing still Assembled to it, from the Seed Box Optional (Before 01/2020) RH Support and Seed Rate Adjusting Screw. 8. At the center of the Seeder where the RH and LH Hex 1.
- Page 51 TABLE OF CONTENTS 11. Remove the Mounting Plate Hardware and slide the 18. Assemble RH Rear Seed Box onto RH Double Box LH Seed Box far enough to the right to remove the Support with two 1/2-13 x 1-1/4 Bolts and a 3/8-16 x Mounting Plate from the Seed Box and Transmission.
- Page 52 TABLE OF CONTENTS 27. Install Front Seed Shaft Coupler and tighten Rear 29. 8FT and 10FT Seeders: Install RH and LH Light Seed Box Feed Roll Coupler Assembly Set Screws Brackets. against the Seed Shaft and tighten Jam Nuts against 12FT Seeders: Install Turnbuckles to Double Box RH Feed Roll Coupler.
- Page 53 TABLE OF CONTENTS Table provided for general use. NOTES: 9K998-2306 2-35...
- Page 54 TABLE OF CONTENTS Scraper Kit, Tube Mounted - U-Bolt,1/2-13 x Optional Bracket with 4-1/2 x 7-1/2 4-Hole Plate IMPORTANT Seeder Frame Cannot be used with Coil Tine Track Remover Kit. Tube NOTE If Seeder has been used, check Front Roller Assembly Wheels that they are tight to one another before installing Scraper Kit.
- Page 55 TABLE OF CONTENTS S-Tine Bracket Tube Scraper Bracket Locknut,Flanged,1/2-13 S-Tine Bracket U-Bolt,1/2-13 x 4-9/16 x 3-1/4 Scraper Scraper Tube Figure 2-62: Tube Mounted Scrapers with S-Tine Tire Track Remover 4. Center Scraper Tube with the Seeder Front Roller. Seeder Frame 5.
- Page 56 TABLE OF CONTENTS Bracket Bracket Frame Scraper Bracket 13-5/8" 76" 14-7/8" 8FT Seeder Bracket Bracket Scraper Bracket Frame Scraper Bracket 28" 24-1/4" 74-1/2" 28" 10FT Seeder Bracket Scraper Bracket Bracket Frame Scraper Bracket 43" 22-3/16" 103-3/16" 26" 12FT Seeder Figure 2-64: Scraper Mounting Dimensions - Pull-Type 2-38 9K998-2306...
- Page 57 TABLE OF CONTENTS Bracket Bracket Frame Scraper Bracket 13-5/8" 76" 14-7/8" 8FT Seeder Bracket Bracket Scraper Bracket Frame Scraper Bracket 28" 24-1/4" 74-1/2" 28" 10FT Seeder Bracket Scraper Bracket Bracket Frame Scraper Bracket 43" 22-3/16" 103-3/16" 26" 12FT Seeder Figure 2-65: Scraper Mounting Dimensions - 3PT Hitch 9K998-2306 2-39...
- Page 58 TABLE OF CONTENTS S-Tine Tire Track Remover Kit - Optional Tooth Tube IMPORTANT S-Tines should not be operated any deeper than necessary to remove Tractor Tire Tracks. Wet soil will stick to the Front Roller Wheels. As the S-Tine draft load is increased the S-Tines may deflect back and make contact with the Front Roller and break.
- Page 59 TABLE OF CONTENTS Lock Washer,1/2 U-Bolt,1/2-13 x 7-1/2 x 4-1/2 Nut,1/2-13 S-Tine Bracket Clamp Strap Carriage Bolt, Lock 7/16-14 x 3-1/2 Washer,1/2 Tooth Tube Bolt, 1/2-13 x 6 Locknut,7/16-14 S-Tine Reversible Point Flange Locknut, 3/8-16 Duck Foot Plow Bolt Point 3/8-16 X 1-3/4 Seeder Frame Tube...
- Page 60 TABLE OF CONTENTS Drawbar 40" 40" Frame S-Tine S-Tine Bracket Bracket Tooth Tube S-Tine 30" S-Tine 60" Tractor Tire 8FT Seeder Center to Center Distance Frame Drawbar 40" 40" S-Tine S-Tine Bracket Bracket Tooth Tube S-Tine 30" S-Tine 60" Tractor Tire 10FT Seeder Center to Center Distance Frame...
- Page 61 TABLE OF CONTENTS Table provided for general use. NOTES: 9K998-2306 2-43...
- Page 62 TABLE OF CONTENTS Coil Tine Track Remover Kit - Optional IMPORTANT Cannot be used with the Scraper Kit 1. Slide the Coil Tines onto the Round Bar so that the straight leg is frontward. See Figure 2-69. 2. Mount an Arm Weldment and a Coil Tine to the Round Bar second hole from the right end and the third hole from the left end with 3/8-16 x 3 Bolts, Flat Washers, Lock Washers and Nuts.
- Page 63 TABLE OF CONTENTS Bolt,3/8-16 x 1-1/4 Hair Pin Cotter Adjusting Angle Place Chain in Adjusting Angle Slot Clevis Pin, 1/2 x 1-1/4 Flat Washer,3/8 Lock Screw Nut,1/2-13 Chain Lock Washer,3/8 Lock Washer,1/2 Nut,3/8-16 Bracket Bolt, Seeder Frame 1/2-13 x 1-3/4 Tube Bolt, 3/8-16 x 2-1/2...
- Page 64 TABLE OF CONTENTS Turfmaker Sprockets - Optional Turfmaker Sprockets provide extra traction in certain soil types. See your Landoll/Brillion dealer for more information. 1. Position the Wheel Spacer between each Sand Wheel. See Figure 2-70. 2. At the end of the process slide a Half Wheel onto the Drum Pipe next to the last Wheel Spacer.
- Page 65 Chapter 3 TABLE OF CONTENTS Operation DANGER DANGER DANGER DANGER Never allow anyone to ride on the seeder at any Always lock the tractor drawbar in the center time. Allowing a person to ride on the machine can position when transporting the unit. Failure to do inflict serious personal injury or death to that so can result in serious injury or death and cause person.
- Page 66 TABLE OF CONTENTS Tractor Preparation DANGER DANGER The Turfmaker Seeder is available as a Pull Type or 3-PT Do not allow any bystanders to stand between mounted version. the tractor and the implement while backing up to • A Pull Type Seeder is equipped to be pulled by a the implement.
- Page 67 TABLE OF CONTENTS 1" Pin 24" 1-1/8" Pin Category 2 Free Link 1-1/4" Bushing 1" Pin 1-7/16" Bushing 15" 1-1/8" Pin Category 2 Quick Coupler Op LargeSeeder3PtHitch 1-1/4" Bushing 1" Pin 1-7/16" Bushing 19" 1-1/8" Pin Category 3 Narrow Quick Coupler Figure 3-1: 3-PT Hitch 9K998-2306...
- Page 68 TABLE OF CONTENTS Attaching/Detaching 3-PT Hitch Seeder Klik Pin WARNING Disengaged To prevent the implement from tipping backward on the frame, disengage parking pin only when the seeder is fully attached to the tractor. Be sure to observe the following sequences. Parking Pin Klik Pin Figure 3-3: Parking Pin Disengaged...
- Page 69 TABLE OF CONTENTS Tractor Preparation for Frame Attaching Pull Type Seeder Cylinder DANGER DANGER Engaged Do not allow any bystanders to stand between the Transport Lock tractor and the implement while backing up to the Hair Pin implement. Cotter 1. Align the Tractor Drawbar with the machine. Raise or lower the Drawbar, as needed, using the Jack.
- Page 70 TABLE OF CONTENTS Attaching/Detaching Pull Frame Type Seeder Cylinder Attaching the Seeder for Field Operations: Seeder parked lowered Hair Pin Cotter 1. Attach Seeder to the Tractor. 2. Raise the Seeder fully to extend the Hydraulic Lift Cylinders and rotate the Transport Locks in the engaged position over the Cylinder Rod.
- Page 71 TABLE OF CONTENTS Hydraulic Lift System Transmission Electric Clutch The Drawbar Seeder is equipped with a Hydraulic Lift IMPORTANT System to raise and lower the unit in the field. At no time use high pressure water or air to clean the WARNING Electric Clutch as damage could occur.
- Page 72 TABLE OF CONTENTS Brillion Elite Mini Monitor • Brillion Elite Mini Monitor is operated on a 12-Volt DC negative ground system. The monitor should be Brillion Elite Mini Monitor provides information to the connected using the existing convenience plug operator and acts as an interface for clutch control. The connection.
- Page 73 TABLE OF CONTENTS Seed Box Rate Adjustment IMPORTANT The Clutch must be disengaged when Seed Shafts WARNING are turned manually for Calibration. Seed Rate Chart is located inside the Seed Box Cover • To prevent damage to seed meters, do not and in this manual.
- Page 74 TABLE OF CONTENTS DO NOT Adjusting Loosen or Adjust Screw 1/2-13 Locknut Seed Shaft Seed Rate DO NOT Adjusting Nut Loosen or Adjust 1/2-13 Locknut Bearing 1-8 Nut Figure 3-12: Rear Seed Box Seed Rate Adjustment IMPORTANT DO NOT Loosen or Adjust the 1/2-13 Locknut. See Figures 3-11 and 3-12.
- Page 75 TABLE OF CONTENTS Table 3-1: Seed Chart, Front Box NOTE Brillion assumes no liability pertaining to seeding rates achieved with this seeder. Rates listed are general in nature and should be used as starting points only. Seed varieties and blends listed represent those calibrated through in-house test meters. Variations in actual rates may be realized due to differences in seed lots.
- Page 76 TABLE OF CONTENTS Table 3-2: Seed Chart, Rear Box NOTE Brillion assumes no liability pertaining to seeding rates achieved with this seeder. Rates listed are general in nature and should be used as starting points only. Seed varieties and blends listed represent those calibrated through in-house test meters. Variations in actual rates may be realized due to differences in seed lots.
- Page 77 3. Close Meters of Front Seed Box if they contain Seed. is required to disengage the Clutch. 4. Place a Canvas or Tarp under the Machine to catch Landoll assumes no liability pertaining to Seeding Rates Seed. achieved with this Seeder. Rates listed are general in 5.
- Page 78 TABLE OF CONTENTS Idler 22 Tooth Driven 11 Tooth Driver Clutch Idler Shaft 37 Tooth Driven 11/16 Hex 22 Tooth Seed Shaft Driver Figure 3-13: Front Seed Box Transmission Drive (After 01/2020) Idler 22 Tooth Driven 23 Tooth Driven Idler 11 Tooth Driver Clutch...
- Page 79 TABLE OF CONTENTS OPTIONAL TIGHTENER 22 TOOTH DRIVER 23 TOOTH DRIVEN 11/16 HEX 37 TOOTH 11 TOOTH DRIVEN DRIVER Figure 3-15: Transmission Drive (Before 01/2020) 9K998-2306 3-15...
- Page 80 TABLE OF CONTENTS Speed-Up Kit - Optional 3. Remove Roll Pin in the 11-22 Tooth Sprocket. 4. Move the 11-22 Sprocket to new position and replace Seed Rate shown on Seed Rate Charts can be doubled Roll Pin. by using the 22 Tooth Sprocket provided in the 5.
- Page 81 TABLE OF CONTENTS Open Chain at Connector Roll Pin 22T Sprocket 11T Sprocket 4 Pitch Roller Chain Roll Pin 22T Sprocket Figure 3-17: Drive Chain Set for 11 & 22 Tooth Seed Rate (Before 01/2020) 9K998-2306 3-17...
- Page 82 TABLE OF CONTENTS Loup Acre Meter - Optional Total Acres (After 05/15/2012) Press the /FUNC button until the “TOTAL” LED is lit. The digits indicate the acres covered since the total acre counter was cleared. IMPORTANT To clear the total acre count, press and hold the UP and Acre Meter is dust and splash resistant, under no DOWN buttons for two seconds.
- Page 83 TABLE OF CONTENTS Loup Acre Meter - Optional If the display shows “Ent”: You must enter your password using the UP and DOWN buttons. When your (Before 05/15/2012) password is displayed, press the /FUNC button to test the password. If the password is correct, you will be able Settings for Loup Acre Meters to change the acre counter settings.
- Page 84 TABLE OF CONTENTS Table 3-3: Acre Meter Settings (After 05/15/2012) Pulses Width MODEL per 400 FT (Feet) SSPT604 SSP4 SSP5 SSP6 SSP8 SSBP8 SSB8 SSP10 SSBP10 SS10 SSB10 10.0 SSP12 SSBP12 SS12 SSB12 12.0 SSP16 SS16 16.0 SSP108 SS108 SSP110 SS110 10.0 SSP112...
- Page 85 TABLE OF CONTENTS Table 3-4: Acre Meter Settings (Prior to 05/15/2012) MODEL PULSES WIDTH SSP T604 SSP4 SSP5 SSP6 SSP8 SSP10 SS10 SSP12 SS12 SSP108 SS108 SSP110 SS110 SSP112 SS112 SSP208 SSP2081 SS208 SS2081 SSP210 SSP2101 SS210 SS2101 SSP212 SSP2121 SS212 SS2121 SSP308...
- Page 86 TABLE OF CONTENTS Transporting the Seeder 6. Before transporting: • Know the height and width of the implement being 1. Check and follow all federal, state, and local towed. Markers, tanks, attachments, etc. can requirements before transporting the Seeder. increase the height and width of the implement. 2.
- Page 87 Chapter 4 TABLE OF CONTENTS Brillion Elite Mini Monitor Overview • Field Acres and Total Acres • Clutch Control The Brillion Elite Mini Monitor is a full featured display • (Up to 6) Six Seed Shaft Rotation Sensors designed to provide accurate information to the operator •...
- Page 88 TABLE OF CONTENTS 9:30AM SETTINGS BACK APP VER: 2.1.1 SPEED CLUTCH SCROLL UP SETTINGS SETTINGS INSTALL SHAFT SETUP SETTINGS DIAGNOSTICS SETTINGS DISPLAY SCROLL DOWN SETTINGS Figure 4-2: Settings Menu Display (Landscape Seeder) Settings Menu - Source: Shaft Sensor Speed SHAFT SHAFT SPEED Uses the Smart Shaft Sensor...
- Page 89 TABLE OF CONTENTS Speed Source Displays Speed Source Icon Features Pulses Per Revolution SPEED SETTINGS BACK Pulses Per Revolution are the PULSES PER IMP. SWITCH: SOURCE: number of magnets the implement REV: SHAFT SPEED DISABLED mounted speed sensor sees in one revolution of the shaft being monitored.
- Page 90 TABLE OF CONTENTS Speed Calibration Implement Switch Setup All new systems require a ground Implement Switch SPEED SWITCH speed calibration to ensure Setup tells the CALIBRATION SETTINGS accurate area totals and accurate monitor if the ground speed readings. To complete the calibration, Implement Switch IMP.
- Page 91 TABLE OF CONTENTS Settings Menu - Remove A Sensor INSTALL Install Setup Select this option to remove a SETUP REMOVE A sensor from your existing system. RECEIVER SENSOR Select “Install Setup” icon to Learn New System, Add A Sensor, or Remove A Sensor to your machine. 1.
- Page 92 TABLE OF CONTENTS Settings Menu - Settings Menu - SHAFT Shaft Settings GPS Settings RECEIVER SETTINGS RECEIVER SETTINGS “GPS Settings” defines any Baudrate, Speed Seed Shaft Settings Corrections or the current GPS Status. The Seeder can have up to six Smart Shaft Sensors that indicate shaft rotation.
- Page 93 TABLE OF CONTENTS Settings Menu - System Update DISPLAY Display Settings The system update screen is used SETTINGS SYSTEM to update to newer versions of UPDATE software or reset to factory default settings. DISPLAY SETTINGS BACK UNITS UPDATES VOLUME APP VER: 2.1.1 BACK BRIGHTNESS SYSTEM...
- Page 94 TABLE OF CONTENTS Table provided for general use. NOTES: 9K998-2306...
- Page 95 Chapter 5 TABLE OF CONTENTS Maintenance General Torque Specifications (rev. 4/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.
- Page 96 TABLE OF CONTENTS Hydraulic Fitting Torque Specifications 37 degree JIC, ORS, &ORB (REV. 10/97 This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.
- Page 97 TABLE OF CONTENTS Tires 7. Slide the hub, bearing, and seal onto a clean spindle. 8. Install the Outer Bearing Cone and Slotted Nut. 8FT Seeder recommended Tire Size: 9. Tighten the Slotted Nut while rotating the Hub until 9.5L x 15, 8Ply Implement Rib Rating there is a slight resistance to wheel rotation.
- Page 98 TABLE OF CONTENTS Pull Type Frame Wheel Arm Tire and Wheel Assembly Wheel Hub Repack Annually Rear Roller Bearing Rear Arm Rear Roller Pull Type Bearing Seeder Frame Front Roller Bearing 3-PT Seeder Front Roller Frame Bearing Figure 5-2: Lubrication Intervals 9K998-2306...
- Page 99 TABLE OF CONTENTS Hydraulic Maintenance Roller Clamp Bands per Roller Adjustment Procedure. Tighten the Clamp Band Socket Head Bolt (Clamp Band open section) over Roller Drum weld seam to 75 Ft-Lbs. IMPORTANT Thereafter check Front and Rear Roller Assemblies Lower the Drawbar Seeder to the ground, and relieve every 50-100 hours.
- Page 100 TABLE OF CONTENTS Chain Tension Transmission (After 01/2020) Each #40 Drive Chain tension can be adjusted by loosening and adjusting their Tension Idler Sprockets to obtain about 1/8"-1/4" Slack. See Figure 5-4. Adjust the #550 Drive Chain between the Front Roller and Transmission by adjusting the Nylatron Tension Idler to allow approximately 2"...
- Page 101 TABLE OF CONTENTS Transmission (Before 01/2020) To adjust the Transmission Chain, loosen the 5/8" Idler Sprocket Axle Bolt and adjust the Clevis Drawbolt Locknut to obtain about 1/8"-1/4" sag. Re-tighten the Idler Sprocket Axle Bolt. Be careful not to over-tighten this chain.
- Page 102 TABLE OF CONTENTS Seed Meter Adjustment Seed Meter Feed Roll IMPORTANT The Clutch must be disengaged when Seed Shafts are turned manually for Calibration. IMPORTANT All the Seed Meters MUST BE CLOSED! It may be necessary to individually adjust Seed Meter Cups. All Seed Meters must be set the same to ensure uniform seeding.
- Page 103 TABLE OF CONTENTS 4. Front Seed Box: Individual Seed Meter Cups can be adjusted as required. Adjustments can be made by Seed Shaft loosening the 1/4-20 x 5/8 Machine Screws that Coupling Half Bolt,1/4-20 mount the Seed Meter Cup to the Seed Box and the x 1-3/4 1/4-20 Nut that attaches the Seed Meter Support to the Seed Meter Cups.
- Page 104 TABLE OF CONTENTS Warning Lamps Scraper Adjustment When plugging in the 7-Pin Warning Lamp Connector: 1. Check the Front Roller Assembly Wheels that they are tight to one another. See “Front and Rear Roller 1. Make sure the Tractor has a good clean Receptacle, Adjustment”...
- Page 105 TABLE OF CONTENTS Electric Clutch 4. If step 3 works then wave a magnet in front of the Pick-Up Switch face with it re-connected to the display and see if the display increments up. If not, put IMPORTANT an ohm meter or continuity tester on the contacts of If your machine is equipped with an Electric Clutch at the Pick-Up Switch Harness and place a magnet in no time use high pressure water or air to clean it, as...
- Page 106 TABLE OF CONTENTS Storage 1. The service life of the Seeder will be extended by proper off-season storage practices. Prior to storing the unit, complete the following procedures: • Completely clean the unit, blow all seed out of Seed Meters. •...
- Page 107 Chapter 6 TABLE OF CONTENTS Specifications *Specifications subject to change with or without notice. Figure 6-1: Model Specifications (1 of 6) 9K998-2306...
- Page 108 TABLE OF CONTENTS Figure 6-2: Model Specifications (2 of 6) 9K998-2306...
- Page 109 TABLE OF CONTENTS Figure 6-3: Model Specifications (3 of 6) 9K998-2306...
- Page 110 TABLE OF CONTENTS Figure 6-4: Model Specifications (4 of 6) 9K998-2306...
- Page 111 TABLE OF CONTENTS Figure 6-5: Model Specifications (5 of 6) 9K998-2306...
- Page 112 TABLE OF CONTENTS Figure 6-6: Model Specifications (6 of 6) 9K998-2306...
- Page 113 Document Control Revision Log: Date Form # Improvement(s): Description and Comments 03/2007 9K998 Initial Release 01/2020 9K998-0120 Updated Seed Boxes, Seed Box Calibration, Chain Tension Adjustment 06/2021 9K998-0621 ECN 47093 - Hub & Spindle Asm Update to 6 Bolt 05/2022 9K998-0522 ECN 46900, 47696 - Add Brillion Elite Mini Monitor by Loup ECN 47474 - Add QR Code Decal...
- Page 114 Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Turfmaker II Models SL2081/SL2101/SL2121 SLP2081/SLP2101/SLP2121 SLB2081/SLB2101/SLB2121 SLPB2081/SLPB2101/SLPB2121 Operator’s Manual Re-Order Part Number 9K998 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...