Download
Share
Print this page
  1. Manuals
  2. Brands
  3. Landoll Manuals
  4. Seeders
  5. Brillion FPS-6
  6. Operator's manual

Landoll Brillion FPS6 Operator's Manual

Food plot seeder
Hide thumbs Also See for Brillion FPS6:

Advertisement

Quick Links

Download this manual
'
Food Plot Seeder
Models FPS6, FPST6, FPSB-6, FPSBT6
Operator's Manual
LANDOLL COMPANY, LLC
1900 North Street
Marysville, Kansas 66508
(785) 562-5381
800-428-5655 ~ WWW.LANDOLL.COM
2P102-2405

Advertisement

loading
Need help?

Need help?

Do you have a question about the Brillion FPS6 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Landoll Brillion FPS6

Summary of Contents for Landoll Brillion FPS6

  • Page 1 ‘ Food Plot Seeder Models FPS6, FPST6, FPSB-6, FPSBT6 Operator’s Manual LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM 2P102-2405...
  • Page 2 Manuals for Food Plot Seeder Manual Number Manual Type 2P102 Operator’s Manual 2P103 Parts Manual...
  • Page 3 DANGER DO NOT operate or perform any maintenance tasks on this equipment until you have completed the following: 1. Receive proper training to operate this equipment safely. 2. Read and understand the operator’s manual. 3. Be thoroughly trained on inspection and repair procedures. Failure to comply with this warning may result in serious injury or possibly death.
  • Page 5 Table of Contents Safety Introduction ............1-1 Description of Unit .
  • Page 6 TABLE OF CONTENTS Rear Agitator Box Seed Rate Adjustment ......3-12 Rear Agitator Box Seed Calibration Procedure .
  • Page 7 Failure to comply with this warning can result in within 10 days of retail purchase, using the Landoll personal injury or death, damage to the implement Corporation Ag Products on-line registration process.
  • Page 8 TABLE OF CONTENTS SAFETY Safety • When applying decals to the implement, be sure to clean the surface to remove any dirt or residue. Where possible, sign placement should protect the NOTE sign from abrasion, damage, or obstruction from mud, Investigation has shown that nearly 1/3 of all farm dirt, oil etc.
  • Page 9 TABLE OF CONTENTS SAFETY Safety Instructions for Towing Protective Equipment Vehicles • Wear protective clothing and equipment appropriate for the job. Avoid loose fitting clothing. The maximum travel speed is the lesser of • Because prolonged exposure to loud noise can •...
  • Page 10 10 TOOTH DRIVER 2-573-010198 23 TOOTH DRIVEN TAKE-UP 17 TOOTH DRIVER (ROLLER AXLE) 2P178 FOR FPS6 SEEDER ITEM 9 - 2P178 Landoll Company, LLC Marysville, Kansas www.landoll.com MODEL # SERIAL # MADE IN USA 1-573-010006 2P046 ITEM 10 - 2P046...
  • Page 11 TABLE OF CONTENTS SAFETY Decal Locations Figure 1-3: Decal Locations 2P102-2405...
  • Page 12 TABLE OF CONTENTS SAFETY Table provided for general use. NOTES: 2P102-2405...
  • Page 13 Chapter 2 TABLE OF CONTENTS Assembly IMPORTANT CAUTION All harnesses must be firmly attached to machine Do Not work on or under this machine unless frame members, so they don’t sag or become torn securely blocked and supported by a hoist or loose by field debris.
  • Page 14 TABLE OF CONTENTS ASSEMBLY Agitator Seed Box - If not 4. Remove existing Seed Box Drive Chain and set it aside. equipped 5. Attach the Mounting Brackets to the ends of the Agitator Seed Box Assembly with 3/8-16 x 1 Bolts, NOTE Lock Washers, and Nuts.
  • Page 15 TABLE OF CONTENTS ASSEMBLY Nut,3/8-16 Lock Cover Washer,3/8 Bolt,1/2-13 x 1-1/4 Bolt, Sq Head Bolt 3/8-16 x 1 Shifter Handle Flat Shifter Plate Agitator Washer,3/8 Washer,Sq Seed Box Bore 12ga Flat Washer,1/2 Mounting Wing Nut, Lock Bracket 3/8-16 Washer,1/2 Bolt, 1/2-13 x 1 Nut,1/2-13 Figure 2-4: Agitator Seed Box Assembly...
  • Page 16 TABLE OF CONTENTS ASSEMBLY Cargo/Rock Box - Optional 1. Attach Cargo/Rock Box to Frame angles just in front of the Seed Box with 1/2-13 x 1-1/2 Bolt, Flat Washers and Locknuts. See Figure 2-6. Bolt,1/2-13 x 1-1/2 Lock Washer,1/2 Cargo/Rock Box Locknut,1/2-13 Figure 2-6: Cargo/Rock Box 2P102-2405...
  • Page 17 TABLE OF CONTENTS ASSEMBLY Coil Tine Drag - Optional 3. Attach the Pipe and Tine Assembly to the RH and LH Coil Tine Brackets with Clamps, 1/2-13 x 1-1/2 Bolts, 1. Insert a 5/8-11 x 1-3/4 Bolt from the inside out into and Locknuts.
  • Page 18 TABLE OF CONTENTS ASSEMBLY Positive Drive Roller - Optional Drive Seed Box Chain Drive Chain 1. Lower Seeder on a level surface. 2. Removed Coil Tine Drag, if equipped. 3. Remove Scraper Assembly from the Rear of the Seeder Frame. 4.
  • Page 19 TABLE OF CONTENTS ASSEMBLY Hardware, Flanged 1/2-20 Bearing Thick Hardware, Washer 1/2-13 Lower Front Chain Guard Roll Pin,1/4x2 Firming Roller Assembly Sprocket, 17 Tooth Lower Rear Chain Guard Chain Shield Figure 2-10: Firming Roller Assembly Hardware, Flanged 1/2-20 Bearing Thick Hardware, Washer 1/2-13...
  • Page 20 TABLE OF CONTENTS ASSEMBLY Acre Meter Kit - Optional 9. Attach the Pick-Up Switch short ground wire to the small hole in the Switch Bracket with #6-32 x 1/2 The Acre Meter consists of three main parts, the Acre Screw and Nut. Remove paint under the wire Meter, the Pick-Up Switch and the Magnet Wheel connector to assure a good electrical ground Assembly.
  • Page 21 TABLE OF CONTENTS ASSEMBLY 15. Attach the Acre Meter Assembly Bracket to the Seed Box with 3/8-16 x 1 Bolts, Flat Washers, Lock Pick-Up Adhesive Switch Washers, and Nuts. Mount Base 16. Connect the Acre Meter and Pick-Up Switch Switch Bracket Connectors.
  • Page 22 TABLE OF CONTENTS ASSEMBLY Table provided for general use. NOTES: 2-10 2P102-2405...
  • Page 23 Chapter 3 TABLE OF CONTENTS Operation DANGER DANGER DANGER DANGER Never allow anyone a ride on the seeder at any Always lock the tractor drawbar in the center time. Allowing a person to ride on the machine can position when transporting the unit. Failure to do inflict serious personal injury or death to that so can result in serious injury or death and cause person.
  • Page 24 TABLE OF CONTENTS OPERATION Tractor Preparation - Tractor Upper Link length, as necessary. Refer to the Tractor Operator’s Manual. Attaching/Detaching 6. With the Seeder on level surface and attached to the tractor, adjust the tractor 3-PT Hitch Upper Link so Tractor Preparation that the Float Link Pin is at the center of the Float Link Slot for proper floating during seeding.
  • Page 25 TABLE OF CONTENTS OPERATION Float Link Float Link 3/4" Pin 19" 7/8" Pin 2" Spacer Category 1 Free Link Bushing 1-7/16" Bushing 1" Bushing 3/4" Pin Float Link Float Link 24" 7/8" Pin 1-1/8" Category 2 Free Link Bushing 2" Spacer Bushing Figure 3-2: 3-PT Hitch Free Link 2P102-2405...
  • Page 26 TABLE OF CONTENTS OPERATION Float Link Float Link 1-1/4" Bushing 3/4" Pin 15" 7/8" Pin 2" Spacer Category 1 Quick Coupler Bushing 1-7/16" Bushing Float Link Float Link 1-1/4" Bushing 3/4" Pin 15" 7/8" Pin Category 2 Quick Coupler 1-7/16" Bushing 2"...
  • Page 27 TABLE OF CONTENTS OPERATION General Operation Transmission Cover 1. The minimum horsepower requirement is 35 HP. This will vary widely due to speed, moisture, and types of Kilk Pin soils. Local dealers can help in making recommendations for your areas. 2.
  • Page 28 TABLE OF CONTENTS OPERATION Disc Gang Adjustment To adjust the Gang Angle: 1. Loosen the inner 3/4-10 x 3-1/2 Bolt and Locknut. See Disc Gangs should be set approximately 1/2" deep during Figure 3-5. seeding. 2. Remove the outer 3/4-10 Bolt and Locknut. The depth of the Disc Gang can be controlled by adjusting 3.
  • Page 29 TABLE OF CONTENTS OPERATION S-Tine Adjustment S-Tine Depth can be adjusted by raising and lowering the REAR Front and Rear S-Tine Tooth Bars. A good starting point is to set the S-Tines depth level with the Disc Gangs. S-Tine Tooth Bars can raise the S-Tines completely out of the soil for instances where they are not needed.
  • Page 30 TABLE OF CONTENTS OPERATION Front Seed Box Seed Rate Seed Rate Chart is located inside the Seed Box Cover and in this manual. See Figure 3-14. It should be used as Adjustment a reference only. Because of seed variation, a more accurate rate can be determined by performing Front Meter Box Seed Calibration Procedure to calibrate the WARNING...
  • Page 31 TABLE OF CONTENTS OPERATION Front Meter Box Seed Calibration Procedure Transmission Cover NOTE Kilk Pin The information listed in the Seed Charts is subject to change without notice. IMPORTANT Planting rates are in pounds per acre. Kilk Pin Storage Brillion assumes no liability pertaining to Seeding Rates achieved with this Seeder.
  • Page 32 TABLE OF CONTENTS OPERATION Agitator Seed Box Tension 23 Tooth Driven Idler Klik-Pin Rear Seed Box Disconnect Meter Seed Box 26 Tooth Driven Front Seed Box 5/8 Calibration Hex on frame exterior FRONT 10 Tooth Driver 10 Tooth Driver 37 Tooth Driven Tension Idler 23 Tooth Driven Rear Roller...
  • Page 33 TABLE OF CONTENTS OPERATION Figure 3-14: Seed Rate Chart - Meter Seed Box 2P102-2405 3-11...
  • Page 34 TABLE OF CONTENTS OPERATION Rear Agitator Box Seed Rate Rear Agitator Box Seed Adjustment Calibration Procedure The Seed Rate is adjusted by Shifting the Shifter Handle NOTE on the back of the Seed Box. Loosen the Wing Nut to move the Shifter Handle to the desired setting and The information listed in the Seed Charts is subject to re-tighten the Wing Nut.
  • Page 35 TABLE OF CONTENTS OPERATION Figure 3-16: Seed Rate Chart - Agitator Seed Box 2P102-2405 3-13...
  • Page 36 TABLE OF CONTENTS OPERATION Loup Acre Meter Kit - Total Acres Optional (After 05/15/2012) Press the /FUNC button until the “TOTAL” LED is lit. The digits indicate the acres covered since the total acre counter was cleared. IMPORTANT To clear the total acre count, press and hold the UP and Acre Meter is dust and splash resistant, under no DOWN buttons for two seconds.
  • Page 37 TABLE OF CONTENTS OPERATION If the display shows “Ent”: You must enter your password using the UP and DOWN buttons. When your password is displayed, press the /FUNC button to test the password. If the password is correct, you will be able to change the acre counter settings.
  • Page 38 TABLE OF CONTENTS OPERATION Acre Meter Settings MODEL Pulses per 400 FT Width (Feet) SSPT604 SSP4 SSB4 SSP5 SSB5 SSP6 SSB6 SSP8 SSBP8 SSB8 SSP10 SSBP10 SS10 SSB10 10.0 SSP12 SSBP12 SS12 SSB12 12.0 SSP16 SS16 4610-16 16.0 SSP108 SS108 SSP110 SS110 10.0...
  • Page 39 TABLE OF CONTENTS OPERATION Transporting the Seeder 5. Check to see that the tractor hitch capacity is rated to carry the weight of the Seeder. Refer to Tractor 1. Check and follow all federal, state, and local Operator’s Manual. requirements before transporting the Seeder. 6.
  • Page 40 TABLE OF CONTENTS OPERATION Table provided for general use. NOTES: 3-18 2P102-2405...
  • Page 41 Chapter 4 TABLE OF CONTENTS Maintenance General Torque Specifications (rev. 4/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.
  • Page 42 TABLE OF CONTENTS MAINTENANCE Hydraulic Fitting Torque Specifications 37 degree JIC, ORS, &ORB (REV. 10/97 This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.
  • Page 43 TABLE OF CONTENTS MAINTENANCE Fasteners Lubrication Maintenance Before operating your Brillion machine, check all WARNING hardware for tightness. Use the Tightening Torque Table as a guide. See Page 4-1. Do Not lubricate Seeder while in motion. If any After a few hours of use, check entire machine and Guards is opened for lubricating, it must be tighten any loose nuts or bolts.
  • Page 44 TABLE OF CONTENTS MAINTENANCE Firming Roller Adjustment After an initial run of 5-10 hours, check the Firming Roller Assembly to ensure that the Roller Wheels and Star Sprockets are tight to one another and that the clamped Star Sprocket 1/2-13 Hardware on the RH end of the Forming Roller is tight.
  • Page 45 TABLE OF CONTENTS MAINTENANCE Chain Tension To adjust, loosen the appropriate Tension Idler Hardware and move the Tension Idler until 1/8" to 3/16" slack is achieved. Retighten the Tension Idler Hardware. IMPORTANT Do not over-tighten the Seed Box Drive Chain. Over-tightening will cause the 26 Tooth Sprocket Assembly Bearing to fail.
  • Page 46 TABLE OF CONTENTS MAINTENANCE Seed Meter Adjustment Seed Meter Cup IMPORTANT Washer Remove all seed out of the Meter Seed Box and Seed Seed Meter Cup Meters before adjusting the Seed Meters. Star Washer IMPORTANT All the Seed Meters MUST BE CLOSED! It may be necessary to individually adjust Seed Meter Cups.
  • Page 47 TABLE OF CONTENTS MAINTENANCE Agitator Box Slide 4. Check that the Shifter Handle functions properly in relationship with the Shifter Plate. Adjustment • Shift the Shifter Handle to “0”. The Agitator Box bottom opening should be fully closed. See When the Agitator Box Slide is properly adjusted, the Figure 4-10.
  • Page 48 TABLE OF CONTENTS MAINTENANCE Acre Meter Troubleshooting 2. Verify that the magnet in the Magnet Wheel Assembly has not come out. 3. Place the Acre Meter display in “Calibrate” mode by IMPORTANT pressing the *(FUNC) key until the “P-Word” Acre Meter is dust and splash resistant, under no indicator is lit and then press the up/down arrow keys circumstances should this unit be submerged in any until the display shows 0 and the LED is blinking.
  • Page 49 Chapter 5 TABLE OF CONTENTS Specifications Product Attributes FPSB 6 Approximate Weight 1,389 lbs. (625 kg) Working Width 6 ft. 0 in. (1.8 m) Overall Width 6 ft. 10 in. (2.05 m) Overall Transport Height Dependent Upon Tractor Overall Height (Working) 3 ft.
  • Page 50 TABLE OF CONTENTS SPECIFICATIONS Table provided for general use. NOTES: 2P102-2405...
  • Page 51 2P102-0911 (205rev0911) ECN 35017, 35166 - Improved improved pictures and drawings. 03/18/2012 2P102-0312 (205rev0312) ECN 35504. Corrected Planting Rate Values. 05/2024 2P102-2405 ECN 49704 - Landoll P/N, Decals, Acre Meter etc. *Revision Format “Year/Month” Updated ISO logos to ISO 9001:2015...
  • Page 52 Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001:2015 registration at all Landoll manufacturing facilities. Food Plot Seeder Model FPSB-6 Operator’s Manual Re-Order Part Number 2P102 LANDOLL COMPANY, LLC 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM...

This manual is also suitable for:

Brillion fpst6Brillion fpsb-6Brillion fpsbt6