Proper assembly, within 10 days of retail purchase, using the Landoll maintenance and safe operation will allow this implement Corporation Ag Products on-line registration process.
SAFETY INFORMATION Federal law requires that you explain the safety and Order replacement decals through your Brillion dealer. operating instructions furnished with this implement to all Keep these signs clean so they can be observed readily. operators before they are allowed to operate the It is important to keep these decals cleaned more implement.
SAFETY INFORMATION Keep clear of overhead power lines and other Any fluid injected into the skin must be surgically obstructions when transporting. Know transport height removed within a few hours or gangrene may result. and width of your implement. Refer to transport Avoid the hazard by relieving pressure before dimensions.
Page 8
SAFETY INFORMATION Figure 1-2: Decals 7K555...
Page 9
SAFETY INFORMATION Figure 1-3: SSP4 Decals...
Page 10
SAFETY INFORMATION Figure 1-4: SSP5 and 6 Decals 7K555...
Chapter 2 Assembly of Optional Equipment The intent of this chapter is to provide instructions allowing you to safely and correctly assemble your Brillion product. CAUTION Do not work on or under this implement unless securely blocked and supported by a hoist or tractor or by other sufficient means! Agitator Blades (Optional Cage or Brushes)
ASSEMBLY OF OPTIONAL EQUIPMENT Figure 2-2: Agitators Lift Sling Kit (Optional) 1. If not already assembled to the machine, attach a mounting bracket to each side of machine at the center holes of the right and left end plates. (A strap may need to be added to one side to equalize the thickness of plates on the both sides of the machine.) 2.
ASSEMBLY OF OPTIONAL EQUIPMENT Acre Meter (Optional) 3. Mount the acre meter onto this bracket with #10-24 x 1” bolts, lockwashers and nuts. The acre meter, consisting of three main parts; the acre 4. Then run the wire from the bottom of the meter down meter, the pick-up, and the magnet wheel, is mounted on the side of the seed box and along its left side.
Page 15
ASSEMBLY OF OPTIONAL EQUIPMENT 5. At the rear of the seeder, mount the L-shaped 6. Extend its longer wire up toward the side of the bracket to the end plate with a 5/8-11 x 1-1/2” bolt seedbox to meet the wire from the acre meter. Attach and locknut as shown.
Page 16
ASSEMBLY OF OPTIONAL EQUIPMENT Page Intentionally Blank 7K555...
This chapter covers the basic operation and usage To prevent the implement from tipping backward procedures for the Landoll Brillion Sure Stand Seeder. on the frame, disengage the parking pin only Be sure to read and understand the Safety Procedures when the seeder is fully attached to the tractor.
OPERATION Seed Rate Adjustment- Front Pointer Adjustment With cups completely closed, pointer should point to groove in hex shaft marked “0”. If it does not, Adjusting Seed Cups: adjust the nuts which clamp the pointer spring bolt to the All cups must be set the same in order to seed uniformly. frame end plates.
OPERATION When the handle is moved to ‘0’ the holes in the box WARNING should be completely covered. If the holes are not covered, loosen the three bolts holding the seedmeter • To prevent damage to the seed meters, do not casting and shift it slightly so that the “0”...
OPERATION Seed Rate Calibration PLANTING RATES FOR SEED METER (FRONT BOX) IN POUNDS PER ACRE: The provided charts were determined by laboratory tests • Rates are for the 13-Tooth Driver Sprocket. on various samples. To find rates for specific seed lots or •...
Page 21
OPERATION Planting Rates for 4 and 5 Foot Seeders Continued Indicator Setting Love Grass (Sand) Millet Red Top Reed Canary Grass Switch Grass (Cleaned and Hulled) Timothy Table 3-2: Planting Rate for 6 Foot Seeder Indicator Setting Alfalfa (Uncoated Bahia Bermuda (Hulled) Birdsfoot Trefoil (Broadleaf) Blue Grass (Kentucky)
Page 22
OPERATION PLANTING RATES FOR SEED METER • Rates are for 13-Tooth Driver Sprocket. (REAR BOX) IN POUNDS PER ACRE: 4, 5 • Rates are intended as a guide only. Variations in size and cleanliness will affect rates. Check acreage & and 6 FOOT SEEDER pounds of seed used for best results.
OPERATION Chain Tension • To adjust the 3rd drive chain, loosen the 3/4” Hex bolt and adjust to obtain just enough sag so that the upper Chain tension must be carefully considered so that the and lower chain strands do not touch each other. loads created on the components will not be too Re-tighten axle bolt.
OPERATION Adjustment of the Wheel Track Remover The depth of the wheel track removers can be adjusted. Loosen the (4) 1/2-13 X 1-1/4 bolts, and nuts that secure the clamps to the coil tine supports. Adjust the supports up or down to the desired depth and then retighten the nuts on the bolts.
OPERATION Settings for Loup Acre Meters If you do not know the pulses per mile, press and hold the UP and DOWN buttons until the “0000” appears in the After 05/15/2012 display. The “PULSES” LED will blink. The acre counter is now counting shaft rotations.
OPERATION Changing The Password 3. Press the function button to set password; screen will show “(set)”. Record number - it is required if you Select a new password using the UP and DOWN buttons. decide to disable password. Press the /FUNC button until the word “SEt”...
Chapter 4 Maintenance & Specifications General Torque Specifications This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.
MAINTENANCE & SPECIFICATIONS Hydraulic Fitting Torque Specifications 37 degree JIC, ORS, &ORB (REV. 10/97 This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used.
MAINTENANCE & SPECIFICATIONS Acre Meter After a few hours of use, check the entire machine and tighten any loose nuts or bolts. Daily or periodic checks The battery operated acre counter uses 3 AA batteries. should be made thereafter. The acre counter will display “LObat” when the batteries •...
MAINTENANCE & SPECIFICATIONS Reference Tables and Specifications Table 4-1: Model and Weight Specifications Model Description Weight SSP4 4’ Sure Stand Seeder, Pick-Up Type 5’ Sure Stand Seeder, Pick-Up Type SSP5 1007 SSP6 6’ Sure Stand Seeder, Pick-Up Type 1100 Table 4-2: Dimensions Dimensions 4 ft.
Page 34
Equipment from Landoll Company, LLC is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. Sure Stand Seeder Models - SSP4, SSP5 and SSP6 Operator’s Manual Re-Order Part Number 7K555rev0620 LANDOLL COMPANY, LLC 1900 North Street...