Subscribe to Our Youtube Channel
Related Manuals for Landoll Brillion 4630-36 Series
Summary of Contents for Landoll Brillion 4630-36 Series
- Page 1 4630-36 Folding Seeder Operator’s Manual LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM F-640-0615 06/2015...
-
Page 3: Table Of Contents
Table of Contents Introduction Understanding Safety Statements ..........1-2 Standard Specifications General Torque Specifications (rev. - Page 4 Parking ..............4-16 Lubrication Maintenance .
-
Page 5: Introduction
Chapter 1 Introduction The Landoll 4630-36 Folding Seeder is a quality product designed to give years of trouble free performance. By following each section of this manual, your system will perform as designed for you and your operation CHAPTER 1 gives basic instructions on the use of this manual. -
Page 6: Understanding Safety Statements
INTRODUCTION Understanding Safety Statements You will find various types of safety information on the following pages and on the machine signs (decals) attached to the vehicle. This section explains their meaning. The Safety Alert Symbol means ATTENTION! YOUR SAFETY IS INVOLVED! ... -
Page 7: Standard Specifications
Chapter 2 Standard Specifications 4630-36 SERIES FOLDING SEEDER ESTIMATED MODEL WORKING TRANSPORT TRANSPORT TRANSPORT TIRE AND WEIGHT NUMBER WIDTH HEIGHT LENGTH WIDTH WHEELS (LBS.) 4630-36 36’-0” 11’-0” 34’-0” (w/ 13’-6” (4) 12L x 15, Load Range F - * 18,100 - seeders) or 8 bolt (frame) 20,366 Lbs. -
Page 8: General Torque Specifications (Rev. 4/97)
STANDARD SPECIFICATIONS General Torque Specifications (rev. 4/97) This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used. -
Page 9: Parker® Brand Fittings
STANDARD SPECIFICATIONS Hydraulic Fitting Torque Specifications 37 degree JIC, ORS, &ORB (REV. 10/97 This chart provides tightening torques for general purpose applications when special torques are not specified on process or drawing. Assembly torques apply to plated nuts and capscrews assembled without supplemental lubrication (as received condition). They do not apply if special graphite moly-disulfide or other extreme pressure lubricants are used. - Page 10 STANDARD SPECIFICATIONS 31-21/32 34-1/8 2-21/32 5-29/32 2-15/32 (5-11/32) 30-7/8 33-1/8 15-15/16 (64) 4630-36 harrow placement Figure 2-1: 4630-36 Folding Seeder Harrow Placement F-640-0615 Edition...
-
Page 11: Assembly Instructions
Chapter 3 Assembly Instructions Your new 4630-36 Folding Seeder comes nearly WARNING completely assembled from the factory and ready to go to the field. Do not attempt to lift heavy parts (such as the frame, wheel lift, and pull hitch) manually. Use a To insure alignment of assemblies, leave the nuts loose hoist or a forklift to move these parts into until completion of final assembly. - Page 12 ASSEMBLY INSTRUCTIONS Figure 3-1: Seeder Attachment or Removal from Seeder Hitch F-640-0615 Edition...
-
Page 13: Seeder Attachment To Seeder Hitch
ASSEMBLY INSTRUCTIONS Seeder Attachment to Seeder Seeder Removal from Seeder Hitch Hitch CAUTION CAUTION Secure the Seeder Hitch to a tractor and unfold Secure the Seeder Hitch to a tractor and unfold the wings of the hitch when attaching seeder the wings of the hitch when removing seeder unit(s). -
Page 14: Seed Shaft Sensors
ASSEMBLY INSTRUCTIONS Seed Shaft Sensors 9. If you have a double box seeder connect the plug labeled “Left Rear Seed Shaft Sensor” to the left rear Mount Console with Clutch Control on Tractor. See Seed Shaft Sensor. Otherwise, seal the plug end Figure 3-2. -
Page 15: Single Box Sensor Schematic
ASSEMBLY INSTRUCTIONS Single Box Sensor Schematic Figure 3-3: Single Box Sensor Schematic... -
Page 16: Double Box Sensor Schematic
ASSEMBLY INSTRUCTIONS Double Box Sensor Schematic Figure 3-4: Double Box Sensor Schematic F-640-0615 Edition... -
Page 17: Seed Shaft Sensor Mounting Dimension
ASSEMBLY INSTRUCTIONS Seed Shaft Sensor Mounting NOTES Dimension Depending on the seeding rate it may be necessary to Check pre-assembled Seed Shaft Sensor and Bracket so move sensor left or right in bracket slot to ensure magnet the center line of magnet wheel and sensor are is within sensor range, since magnet moves with seed horizontally and vertically aligned with a maximum 1/8”... - Page 18 ASSEMBLY INSTRUCTIONS Table provided for general use. NOTES: F-640-0615 Edition...
-
Page 19: Operation And Maintenance
Chapter 4 Operation and Maintenance DANGER DANGER Never allow anyone to ride on the 4630-36 Folding Always lock the tractor drawbar in the center Seeder at any time. Allowing a person to ride on position when transporting the unit. Failure to do the machine can inflict serious personal injury or so can result in serious injury or death and cause death to that person. -
Page 20: Tractor Preparation
OPERATION AND MAINTENANCE Tractor Preparation Seeder Hitch Preparation The Landoll 4630-36 Folding Seeder is designed to be 1. Prior to operating the 4630-36 Folding Seeder, read pulled by tractor equipped with a double lip or clevis type and understand the operator's manual and all decals. -
Page 21: Attaching Seeder Hitch To The Tractor
OPERATION AND MAINTENANCE Attaching Seeder Hitch To The WARNING Tractor Escaping fluid under pressure can penetrate the skin causing serious personnel injury. Avoid the DANGER hazard by relieving system pressure before disconnecting hydraulic lines. Tighten all Do not allow any bystanders to stand between the connections before applying pressure. -
Page 22: Transport Locks
OPERATION AND MAINTENANCE Transport Locks 2. To install the telescoping hitch transport lock, fully raise the main lift and hitch. Remove the pin from the 1. Transport lock pins are provided to secure the storage position and install through the hole in the Seeder Hitch in raised and folded positions. -
Page 23: Folding/Unfolding The Seeder Hitch
OPERATION AND MAINTENANCE Folding/Unfolding the Seeder NOTE Hitch Excessive cylinder travel at this point will inhibit unfolding of the seeder hitch. The Seeder Hitch is equipped with hydraulic cylinders to fold and unfold the seeder from transport to field position. d. -
Page 24: Leveling The Hitch Clevis
OPERATION AND MAINTENANCE HITCH CLEVIS HEIGHT ADJUSTMENT 5530-hitchclevis Figure 4-4: Hitch Clevis Height Leveling the Hitch Clevis 2. On a level surface, measure from the ground to the top side of the tractor drawbar. For drawbar heights 1. The hitch clevis height should be adjusted to match 18”... -
Page 25: Leveling The Hitch
OPERATION AND MAINTENANCE Figure 4-5: Top Link Adjustment Leveling the Hitch 1. When unfolding the Seeder Hitch the hitch is lowered to its lowest point to allow the wing fold locks to unhook and clear. Before starting to plant, the hitch should be leveled to insure that the center and wing seeders have the same attitude relative to the field. -
Page 26: Transporting The Seeder Hitch
OPERATION AND MAINTENANCE Figure 4-7: Hitch and Safety Chain Transporting the Seeder Hitch CAUTION 1. Check and follow all federal, state, and local Excessive speed may result in loss of control of requirements before transporting the Seeder Hitch. the tractor and implement, reduced braking, or 2. - Page 27 OPERATION AND MAINTENANCE 6. Slow down when driving on rough roads. Reduce DANGER speed when turning, or on curves and slopes to avoid tipping. Equipment altered other than the place Stay away from power lines when transporting, of manufacture may reduce the maximum transport extending or folding implement.
-
Page 28: Hydraulic Lift System
OPERATION AND MAINTENANCE Hydraulic Lift System 1. The hydraulic lift system contains cylinders plumbed together. The Seeder Hitch is equipped with a hydraulic lift system 2. The main lift cylinders and telescoping hitch are to raise and lower the unit from transport to planting connected together on the same hydraulic circuit. -
Page 29: Seed Shaft Monitor With Clutch Control
OPERATION AND MAINTENANCE Seed Shaft Monitor with Clutch a fully functional condition. The LED for other shafts will indicate a second fault but the alarm will not sound Control unless all shafts are functional after the INITIAL alarm. Basic Operation: NOTE During normal operation the monitor LED for each shaft If shaft sensor stall alarm occurs, be aware that the... -
Page 30: Hydraulic Row Markers (Option)
OPERATION AND MAINTENANCE Hydraulic Row Markers (Option) 3. With both markers in the raised position, slowly engage the marker hydraulics. One marker will 1. The Seeder Hitch may be equipped with optional extend. Reversing the hydraulic lever will raise that hydraulic row markers. -
Page 31: Hydraulic Row Marker Disc Adjustment (Option)
OPERATION AND MAINTENANCE Figure 4-10: Hydraulic Row Marker Adjustment Hydraulic Row Marker Disc 2. The disc blade may also be configured to push or pull soil towards the seeder. Adjustment (Option) a. To change the direction of the disc blade, first remove the 4 bolts and dust cap retainer from ... -
Page 32: Wheel Bearing Maintenance
2. Remove the tire. replace all seals. Seal kits are available from your 3. Remove the hub cap, cotter pin, slotted nut and Landoll dealer. washer. 3. Check all hydraulic hoses weekly. Look for binding or 4. Remove the hub. Clean and inspect the bearings and cracking. -
Page 33: Hose Identification
OPERATION AND MAINTENANCE Figure 4-11: Hitch Hose Clamps and Color Designations Hose Identification 2. For the Seeder Hitch, hoses will be identified as follows: 1. The hydraulic hoses are color coded to help identify Blue - Lift Wheels and match the attaching hoses on the Seeder Hitch. Yellow - Wing Fold An identification decal is placed on the front of the Red - Section Lifts... -
Page 34: Parking
OPERATION AND MAINTENANCE Parking 3. To park the seeder with the wings unfolded: 1. When unhitching the Seeder Hitch from the tractor, it WARNING is best to park in the folded position whenever possible. This gives the seeder the smallest storage The Seeder Hitch has negative tongue weight footprint. - Page 35 OPERATION AND MAINTENANCE Figure 4-13: Lubrication Points 4-17...
-
Page 36: Lubrication Maintenance
OPERATION AND MAINTENANCE LUBRICATION TABLE INTERVAL ITEM DESCRIPTION NO. OF LUBE POINTS (Hours Unless Stated) Wing Hinge 1 each Inner Wing Pivot Marker Arm Marker Hub Table 4-1: Lubrication Table Lubrication Maintenance Storage 1. Table 4-1 specifies the lubrication points and Preparing the Seeder Hitch for storage during extended intervals on the 4630-36 Folding Seeder. -
Page 37: Troubleshooting Guide
Chapter 5 Troubleshooting Guide For any questions concerning operation or maintenance of the seeders, refer to the operator’s and parts manuals as designated in “AVAILABLE SEEDER OPTIONS” on page 2-1. Troubleshooting Guide PROBLEM PROBLEM CAUSE SOLUTION Power LED does not Power fuse blown due to system fault Inspect wire harness for damage or shorts illuminate Replace 15 Amp fuse... - Page 38 TROUBLESHOOTING GUIDE Table provided for general use. NOTES: F-640-0615 Edition...
- Page 40 Equipment from Landoll Corporation is built to exacting standards ensured by ISO 9001 registration at all Landoll manufacturing facilities. 4630-36 Folding Seeder Operator’s Manual Re-Order Part Number F-640-0615 LANDOLL CORPORATION 1900 North Street Marysville, Kansas 66508 (785) 562-5381 800-428-5655 ~ WWW.LANDOLL.COM Copyright 2010.
Need help?
Do you have a question about the Brillion 4630-36 Series and is the answer not in the manual?
Questions and answers