Timer Function - AUMA AUMATIC AC 01.2 Manual

Appendix
No. Type Parameter
16-3 enum EMCY failure source
16-4 enum EMCY operation
16-5 U16 EMCY position
16-6 enum By-pass torque
16-7 enum Thermal by-pass
16-8 enum By-pass timer
16-9 enum By-pass operat.profile
16-10 enum By-pass Interlock
16-11 enum By-pass Local STOP
16-12 Mmss01 Delay time
16-13 U16 EMCY position MPV
Table 48: Timer function
No. Type Parameter
Offset (hexadecimal) = 0x04C1
Offset (decimal) = 1217
Data length = 20 bytes
17-1 enum Step mode CLOSE
17-2 Mmss01 On time CLOSE
17-3 Mmss01 Off time CLOSE
17-4 U16 Start stepping CLOSE
17-5 U16 End stepping CLOSE
17-6 enum Step mode OPEN
56
Access Default Setting value
R/W 3 1 : I/O interface
2 : Fieldbus interface
3 : I/O or fieldbus
4 : Active interface
R/W 0 0 : STOP
1 : CLOSE
2 : OPEN
3 : Approach EMCY pos.
R/W 0 Min = 0 [0.1 %]
Max = 1000 [0.1 %]
R/W 0 0 : Off
1 : On
R/W 0 0 : Off
1 : On
R/W 0 0 : Off
1 : On
R/W 0 0 : Off
1 : On
R/W 0 0 : Off
1 : On
R/W 0 0 : Off
1 : On
R 10 Min = 0 [0.1 s]
Max = 1800 [0.1 s]
R/W 10 Min = 0 [0.1 s]
Max = 1800 [0.1 s]
Access Default Setting value
R/W 0 0 : Off
1 : Remote
2 : Local
3 : Remote and local
R/W 50 Min = 10 [0.1 s]
Max = 1800 [0.1 s]
R/W 50 Min = 10 [0.1 s]
Max = 1800 [0.1 s]
R/W 1000 Min = 1 [0.1 %]
Max = 1000 [0.1 %]
R/W 0 Min = 0 [0.1 %]
Max = 999 [0.1 %]
R/W 0 0 : Off
1 : Remote
2 : Local
3 : Remote and local
Actuator controls
AC 01.2/ACExC 01.2 Modbus RTU
Explanation
Failure source for EMERGENCY
behaviour
Actuator reaction in EMER-
GENCY operation mode
Setting the EMERGENCY posi-
tion
By-passing the torque monitor-
ing in EMERGENCY operation
mode
By-passing the thermal monitor-
ing in EMERGENCY operation
mode
By-passing the timer function in
EMERGENCY operation mode
By-pass of operation profile in
EMERGENCY operation mode
By-pass of interlock function in
operation mode EMERGENCY
By-pass of local STOP function
in EMERGENCY operation
mode
Delay time for EMERGENCY
behaviour (EMERGENCY beha-
viour is only executed after the
delay time has expired).
EMERGENCY position of multi-
port valve
Explanation
Setting the operation mode:
Stepping mode in direction
CLOSE
Setting the on time in direction
CLOSE
Setting the off time in direction
CLOSE
Setting the start of stepping
mode in direction CLOSE
Setting the end of stepping
mode in direction CLOSE
Setting the operation mode:
Stepping mode in direction
OPEN