Mwg - AUMA AUMATIC AC 01.2 Manual

Appendix
Table 57: Actuator
No. Type Parameter
Offset (hexadecimal) = 0x04D4
Offset (decimal) = 1236
Data length = 12 bytes
36-1 enum Motor prot. mode
36-2 enum Closing rotation
36-3 enum Handwheel switch
36-4 enum Heater monitor
36-5 U32 Heater monitor. time
Table 58: MWG
No. Type Parameter
Offset (hexadecimal) = 0x04D5
Offset (decimal) = 1237
Data length = 44 bytes
37-1 U16 Nom. torque CLOSE
37-2 U16 FREI_FB_AnaIn1
37-3 U16 CLOSE min. angle
37-4 U16 CLOSE min. torque
37-5 U16 CLOSE max. angle
37-6 U16 CLOSE max. torque
37-7 U16 OPEN min. angle
37-8 U16 OPEN min. torque
37-9 U16 OPEN max. angle
37-10 U16 OPEN max. torque
37-11 U16 Correction CLOSE
37-12 U16 Correction OPEN
37-13 U16 Hysteresis torque
62
Access Default Setting value
R/W 0 0 : Auto
1 : Reset
R 0 0 : Clockwise rotation
1 : Counterclockwise rot.
R 0 0 : Without
1 : NC
2 : NO
R 0 0 : Function not active
1 : Function active
R 3000 Min = 600 [0.1 s]
Max = 36000 [0.1 s]
Access Default Setting value
R 100 Min = 0 [Nm]
Max = 65535 [Nm]
R 100 Min = 0 [Nm]
Max = 65535 [Nm]
R 120 Min = 65
Max = 125
R 50 Min = 20 [%]
Max = 80 [%]
R 105 Min = 8
Max = 122
R 100 Min = 80 [%]
Max = 125 [%]
R 134 Min = 129
Max = 189
R 50 Min = 20 [%]
Max = 80 [%]
R 149 Min = 132
Max = 247
R 100 Min = 80 [%]
Max = 125 [%]
R 100 Min = 80
Max = 120
R 100 Min = 80
Max = 120
R 5 Min = 0
Max = 20
Actuator controls
AC 01.2/ACExC 01.2 Modbus RTU
Explanation
Signal behaviour of motor protec-
tion (thermal monitoring). Auto:
Automatic thermal fault reset
after cooling down. Reset: re-
quires manual thermal fault re-
set after colling down via a RE-
SET command.
Setting the direction of rotation
Handwheel switch
Montitoring the heater in actuat-
or
Monitoring time of heater resp.
of the heating system (warning
"Wrn heater" is issued if a fault
has continuously occurred dur-
ing this period)
Explanation
Setting the nominal torque
CLOSE in Nm
no text
Torque pivot point CLOSE
(minimum angle value)
Torque pivot point CLOSE
(minimum torque)
Torque pivot point CLOSE
(maximum angle value)
Torque pivot point CLOSE
(maximum torque)
Torque pivot point OPEN (min-
imum angle value)
Torque pivot point OPEN (min-
imum torque)
Torque pivot point OPEN (max-
imum angle value)
Torque pivot point OPEN (max-
imum torque)
Correction factor for torque
characteristic CLOSE
Correction factor for torque
characteristic OPEN
Hysteresis of torque switching