Installing Crankshaft (For 3 Cylinders); Installing Crankshaft (For 4 Cylinders) - Kubota D1803-CR-E4 Workshop Manual

4. ENGINE
6.4 Installing crankshaft (for 3
cylinders)
NOTE
• Measure the side clearance of crankshaft when
you assemble again.
• This topic is used for only 3 cylinders engine
(D1803-CR-E4, -TE4, -TIE4).
1. Install the crankshaft until the crankpin of the first
cylinder comes to the center of the third cylinder.
2. Turn the crankshaft
counterclockwise to set the crankpin of the second
cylinder to the bottom dead center.
3. Install the crankshaft until the crankpin of the
second cylinder comes to the center of the third
cylinder.
4. Turn the crankshaft to set the crankpin of the third
cylinder to the bottom dead center.
5. Install the crankshaft completely.
6. Align the screw hole of the main bearing case with
the screw hole of the crankcase.
7. Install the main bearing case screw 2 (1) by hand.
NOTE
• Apply oil to the main bearing case screw 2.
• If you cannot turn the screw 2 smoothly,
align the screw holes between the crankcase
and the main bearing case correctly.
(1) Main bearing case screw 2
8. Tighten the main bearing case screw 2 (1) to
specified torque.
Tightening tor- Main bearing case
que screw 2 (1)
RELATED PAGE
4.30 Measuring angular deviation between crankshaft
T.D.C. and crankshaft position sensor detected T.D.C.
on page 4-112
4-138
by 2.09 rad (120°)
68.6 to 73.5 N⋅m
7.00 to 7.49 kgf⋅m
50.6 to 54.2 lbf⋅ft
D1803-CR-E4,D1803-CR-TE4,D1803-CR-TIE4,V2403-CR-E4,V2403-CR-TE4,V2403-CR-TE4BG,V2403-CR-TIE4
6.5 Installing crankshaft (for 4
cylinders)
NOTE
• Measure the side clearance of crankshaft when
you assemble again.
• This topic is used for only 4 cylinders engine
(V2403-CR-E4, -TE4, -TE4BG, -TIE4).
1. Hold the crankpins to the horizontal directions (right
or left) and install the crankshaft completely into
crankcase.
2. Turn the crankshaft to set the crankpin of the fourth
cylinder to the horizontal directions (right or left).
3. Align the screw hole of the main bearing case with
the screw hole of the crankcase.
4. Install the main bearing case screw 2 (1) by hand.
NOTE
• Apply oil to the main bearing case screw 2.
• If you cannot turn the screw 2 smoothly,
align the screw holes between the crankcase
and the main bearing case correctly.
(1) Main bearing case screw 2
5. Tighten the main bearing case screw 2 (1) to
specified torque.
Tightening tor- Main bearing case
que screw 2 (1)
RELATED PAGE
4.30 Measuring angular deviation between crankshaft
T.D.C. and crankshaft position sensor detected T.D.C.
on page 4-112
SERVICING
6. Assembling
68.6 to 73.5 N⋅m
7.00 to 7.49 kgf⋅m
50.6 to 54.2 lbf⋅ft
KiSC issued 12, 2018 A