009: St.exciter/Enhncr (Stereo Exciter/Enhancer)256; 010: Stereo Isolator - Korg Krome Parameter Manual

You can configure a 21‐Band Graphic EQ ranging from 80
Hz to 18 kHz if you route three Graphic 7‐Band EQ effects in
series, with a setting of 7:Low, 9:Mid, and 11:High for each
EQ.
009: St.Exciter/Enhncr (Stereo
Exciter/Enhancer)
This effect is a combination of the Exciter, which adds a
punch to the sound and the Enhancer, which adds spread
and presence.
Stereo In - Stereo Out
Left
LEQ HEQ
EQ Trim
EQ Trim
Right
D -mod
Exciter Blend –100...+100
a Src Off...Tempo
Amt –100...+100
Emphasis
0...70
Frequency
Src Off...Tempo
b
Amt –70...+70
Enhancer
c Delay L 0.0...50.0
[msec]
Enhancer
d Delay R 0.0...50.0
[msec]
Enhancer
0...100
Depth
e
Src Off...Tempo
Amt –100...+100
f EQ Trim 0...100
Low,
Pre LEQ Fc
Mid-Low
g
High,
Pre HEQ Fc
Mid-High
Pre LEQ Gain
–15.0...+15.0
[dB]
h
Pre HEQ Gain
–15.0...+15.0
[dB]
Dry, 1 : 99...
Wet/Dry
99 : 1, Wet
i Src Off...Tempo
Amt –100...+100
a: Exciter Blend
This parameter sets the depth (intensity) of the Exciter effect.
Positive values give a frequency pattern (to be emphasized)
different from negative values.
b: Emphasis Frequency
This parameter sets the frequency to be emphasized. Higher
values will emphasize lower frequencies.
256
Exciter
Delay
Depth
Delay
Exciter
Enhancer
Sets the intensity (depth) of the
Exciter effect p.256
Selects the modulation source of
the Exciter intensity
Sets the modulation amount of
the Exciter intensity
Sets the frequency to be empha-
sized p.256
Selects the modulation source of
the frequency to be emphasized
Sets the amount of modulation
of the frequency to be empha-
sized
Sets the delay time for the
Enhancer left channel p.256
Sets the delay time for the
Enhancer right channel p.256
Sets the determines to what
degree the Enhancer effect is
applied
Selects the modulation source of
the Enhancer width
Sets the modulation amount of
the Enhancer width
Sets the 2-band EQ input level
Selects the cutoff frequency (low
or mid-low) of the low-range
equalizer
Selects the cutoff frequency
(high or mid-high) of the high-
range equalizer
Sets the gain of the Low EQ
Sets the gain of the High EQ
Sets the balance between the
effect and the dry input
Selects a modulation source for
Wet/Dry
Sets the modulation amount for
Wet/Dry
c: Enhancer Delay L [msec]
d: Enhancer Delay R [msec]
These parameters set the delay time for the Enhancer left
and right channel. Specifying a slightly different delay time
for the left and right channel will add a stereo image, depth,
and width to the sound.

010: Stereo Isolator

This is a stereo effect that separates the input signal into low,
mid, and high‐frequency bands, and controls the volume of
each band independently. For example you can separately
boost or cut the kick, snare, and hi‐hat sounds from a drum
signal in realtime.
Wet / Dry
Stereo In - Stereo Out
Left
Trim
Wet / Dry
Trim
Right
D -mod
D -mod
D -mod
a Trim
b Low/Mid [Hz] 100...500
Mid/High
c
[Hz]
Low Gain [dB]
Src
d
Amt
Mid Gain [dB]
Src
e
Amt
High Gain
[dB]
Src
f
Amt
Wet/Dry
g Src
Amt
Low
Mid
High
Isolator
Low
Mid
High
0...100 Sets the input level
Sets the frequency at which the
low and mid bands are divided
Sets the frequency at which the
2000...6000
mid and high bands are divided
–Inf,
Sets the low-frequency gain
–59...+12
Selects the source that will
Off...Tempo
modulate low-frequency gain
Sets the amount by which the
–72...+72 low-frequency gain will be
modulated
–Inf,
Sets the mid-frequency gain
–59...+12
Selects the modulation source
Off...Tempo
for mid-frequency gain
Sets the amount by which the
–72...+72 mid-frequency gain will be
modulated
–Inf,
Sets the high-frequency gain
–59...+12
Selects the modulation source
Off...Tempo
for high-frequency gain
Sets the amount by which the
–72...+72 high-frequency gain will be
modulated
Dry, 1 : 99... Sets the balance between the
99 : 1, Wet effect and the dry input
Selects a modulation source for
Off...Tempo
Wet/Dry
Sets the modulation amount for
–100...+100
Wet/Dry
Wet / Dry
Wet / Dry