062: Pitch Shifter; 063: Pitch Shifter Bpm - Korg Krome Parameter Manual

062: Pitch Shifter

This effect changes the pitch of the input signal. You can
select from three types: Fast (quick response), Medium, and
Slow (preserves tonal quality). You can also create an effect
in which the pitch is gradually raised (or dropped) using the
delay with feedback.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Input Level
+
Pitch Shifter
Pre
Feedback Position
Input Level
Right
Slow, Switches Pitch Shifter mode
a
Mode
Medium, Fast
Pitch Shift [1/ Sets the pitch shift amount by
–24...+24
2tone] steps of a semitone
Selects the modulation source of
b
Src Off...Tempo
pitch shift amount
Sets the modulation amount of
Amt –24...+24
pitch shift amount
Sets the pitch shift amount by
Fine [cent] –100...+100
steps of a cent
c
Sets the modulation amount of
Amt –100...+100
pitch shift amount
d Delay Time
0...2000 Sets the delay time
[msec]
Feedback Switches the feedback
e Pre, Post
Position connection
Sets the feedback amount
Feedback –100...+100
f
High Damp Sets the damping amount in the
0...100
[%] high range
Input Level Sets the modulation amount of
–100...+100
D-mod [%] the input level
g
Selects the modulation source
Src Off...Tempo
for the input level
Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects a modulation source for
h Src Off...Tempo
Wet/Dry
Sets the modulation amount for
Amt –100...+100
Wet/Dry
a: Mode
This parameter switches the pitch shifter operating mode.
With Slow, tonal quality will not be changed too much. With
Fast, the effect becomes a Pitch Shifter that has a quick
response, but may change the tone. Medium is in‐between
these two. If you do not need to set too much pitch shift
amount, set this parameter to Slow. If you wish to change
the pitch significantly, use Fast.
b: Pitch Shift [1/2tone]
b: Src
b: Amt
c: Fine [cent]
c: Amt
The amount of pitch shift will use the value of the Pitch
Shift plus the Fine value. The amount of modulation will
use the b: Amt value plus the c: Amt.
The same Modulation Source is used for both Pitch Shift
and Fine.
e: Feedback Position
f: Feedback
When Feedback Position is set to Pre, the pitch shifter
output is again input to the pitch shifter. Therefore, if you
specify a higher value for the Feedback parameter, the pitch
Wet / Dry
High Damp
Delay
Post
Feedback
Wet / Dry
p.285
p.285
p.285
p.285
p.285
p.285
p.285
p.285
p.284
p.284
Modulation and Pitch Shift (Mod./P.Shift) 062: Pitch Shifter
will be raised (or lowered) more and more each time
feedback is repeated.
If Feedback Position is set to Post, the feedback signal will
not pass through the pitch shifter again. Even if you specify
a higher value for the Feedback parameter, the pitch‐shifted
sound will be repeated at the same pitch.

063: Pitch Shifter BPM

This pitch shifter enables you to set the delay time to match
the song tempo.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
Input Level
+
Pitch Shifter
Feedback Position
Input Level
Right
Tempo
BPM
Base Note x Times
BPM
Slow,
a Mode
Medium, Fast
Pitch Shift [1/
–24...+24
2tone]
b Src Off...Tempo
Amt –24...+24
Fine [cent] –100...+100
c
Amt –100...+100
MIDI,
BPM 40.00...
300.00
d
Time Over? ---, OVER!
Delay Base
...
Note
e
Times x1...x32
Feedback
f Pre, Post
Position
Feedback –100...+100
g
High Damp
0...100
[%]
Input Level
–100...+100
D-mod [%]
h
Src Off...Tempo
Dry, 1 : 99...
Wet/Dry
99 : 1, Wet
i Src Off...Tempo
Amt –100...+100
d: BPM
e: Delay Base Note
e: Times
The delay time is the duration of Times number of Delay
Base Note note values at the BPM tempo (or if BPM is set to
MIDI, the tempo determined by MIDI Clock).
d: Time Over?
You can set the delay time up to 5,290msec. If the delay time
exceeds this limit, the error message "OVER!" appears on
the display. Set the delay time parameters so that this
message will not appear. Time Over? is only a display
parameter.
Wet / Dry
High Damp
Delay
Post
Pre
Feedback
Wet / Dry
Switches Pitch Shifter mode
p.285
Sets the pitch shift amount in
steps of a semitone p.285
Selects the modulation source of
pitch shift amount p.285
Sets the modulation amount of
pitch shift amount p.285
Sets the pitch shift amount in
steps of one cent p.285
Sets the modulation amount of
pitch shift amount p.285
MIDI syncs to the system tempo;
40–300 sets the tempo manually
for this individual effect p.285
Displays an error message when
the delay time exceeds the
upper limit p.285
Selects the type of notes to
specify the delay time p.285
Sets the number of notes to
specify the delay time p.285
Switches the feedback
connection p.285
Sets the feedback amount
p.285
Sets the damping amount in the
high range
Sets the modulation amount of
the input level p.284
Selects the modulation source
for the input level p.284
Sets the balance between the
effect and the dry input
Selects a modulation source for
Wet/Dry
Sets the modulation amount for
Wet/Dry
285