Prog P8: Routing/Ifx (Insert Effect); 8-1: Routing - Korg Krome Parameter Manual

Program mode

PROG P8: Routing/IFX (Insert Effect)

Here, you can make settings for the insert effects. For
instance, you can:
• Send the output of a oscillator to an insert effect
• Route a sound to an insert effect
• Make detailed settings for insert effects
• Make common LFO settings for effects
For more information, please see "Effect Guide" on
page 235.
8–1: Routing
8–1a
8–1b
8–1d
8–1a: Routing Map
This graphic shows an overview of the insert effects.
Here you can view the status of the input bus to the insert
effect Bus (IFX/Output) Select, the effect you're editing, and
its on/off status and chain status.
This page lets you adjust the routing of the oscillators to the
insert effects. To adjust the other settings shown in this
graphic, please see "8–2: Insert FX Setup" on page 59.
8–1b: Bus Select (All OSCs to)
Bus (IFX/Output) Select
This specifies the output bus for oscillators 1 and 2.
L/R: The oscillators will be output to the L/R bus. Normally
you will choose L/R.
IFX1...5: Output to the IFX1–5 busses.
Off: The oscillator will not be output from the L/R bus, or
IFX1–5 busses. Choose the Off setting if you want the
program oscillator output of the timbre to be connected in
series to a master effect. Use Send1 (to MFX1) and Send2 (to
MFX2) to specify the send levels.
FX Control Bus
Sends the output of the oscillator 1, 2 to an FX Control bus
(two‐channel mono FX Ctrl 1 or 2).
Use the FX Control busses when you want a separate sound
to control the audio input of an effect. You can use two FX
Control busses (each is a two‐channel mono bus) to control
effects in various ways.
For more information, please see "FX Control Buses" on
page 238.
58
8–1
Menu
8–1c
[L/R, IFX1...5, Off]
[Off, 1, 2]
8–1c: Use Dkit Setting
Use DKit Setting
This is shown if Oscillator Mode (Prog 1–1a) is set to Drums
or Double Drums. If Oscillator Mode is set to Single or
Double, this setting is ignored.
On (checked): The Bus (IFX/Output) Select, FX Control
Bus, Send 1, and Send 2 settings (Global 5–5b) for each key
of the selected drum kit will be used. Check this if you want
to apply an individual insert effect to each drum instrument.
Tip: In most preloaded drumkits, the drum instruments have
the same Bus (IFX/Output) Select settings according to their
type, as follows.
Snares → IFX1
Kicks → IFX2
Other → IFX3
Off (unchecked): The Bus (IFX/Output) Select (Prog 8–1b),
FX Control Bus (Prog 8–1b), OSC MFX Send (Prog 8–1d)
settings will be used. All drum instruments will be sent to
the specified bus.
8–1d: OSC MFX Send
OSC1:
OSC1 Send1 (to MFX1)
Sets the volume (send level) at which the output of oscillator
1 will be sent to master effect 1. This applies only when Bus
(IFX/Output) Select (Prog 8–1b) is set to L/R or Off.
If Bus (IFX/Output) Select is set to IFX1–IFX5, the send
levels to master effects 1 and 2 are set by Send 1 and Send 2
(Prog 8–2a) after passing through IFX1–5.
OSC1 Send2 (to MFX2)
Sets the volume (send level) at which the output of oscillator
1 will be sent to master effect 2. For more information,
please see "OSC1 Send1 (to MFX1)" on page 58.
OSC2:
OSC2 Send1 (to MFX1)
OSC2 Send2 (to MFX2)
Sets the volume (send level) at which the output of OSC2
will be sent to master effects 1 and 2. These parameters will
be valid when Oscillator Mode is set to Double or Double
Drums and Bus (IFX/Output) Select is set to L/R or Off.
CC#93 controls OSC 1/2's Send 1 level, and CC#91
controls the Send 2 level. These are controlled on the
global MIDI Channel (Global 1–1a). The actual send
level is determined by multiplying these values with
the send levels of each oscillator.
8–1: Menu Command
V
• 0: Write Program see p. 64
• 1: Exclusive Solo see p. 64
• 2: Auto Song Setup see p. 65
• 3: Copy Insert Effect see p. 66
• 4: Swap Insert Effect see p. 67
For more information, please see "Program: Menu
Command" on page 64.
[Off, On]
[000...127]
[000...127]
[000...127]
[000...127]