Korg Krome Parameter Manual page 249

In the example shown in the next diagram, Oscillators 1 and
2 outputs being sent to IFX1.
If you are connecting the Insert Effects in series, check the
Chain box (Prog 8–2a). Use Chain to (Prog 8–2a) to specify
the destination to which the signal will be chained.
If you check the IFX1 checkbox, the output of IFX1 will be
sent to the input of the IFX you specify in Chain to. Effects
can be chained only in ascending order of their number; for
example IFX1 can be chained to IFX2 through IFX5, and
IFX2 can be chained to IFX3 through IFX5. You can create a
chain of up to five insert effects in series, IFX1 through IFX5.
When the Insert Effects are connected in series, the values of
the Pan: CC#8, Bus, Send1, and Send2 parameters for the
post‐IFX signal will be used.
In the example shown in the next diagram, the Chain check
box is checked, and each Chain to parameter is set to the
subsequent effect, creating a series connection of IFX1 →
IFX2 → IFX3 → IFX4 → IFX5. The post‐IFX5 settings for Pan:
CC#8, Bus, Send1, and Send2 will be used.
Settings for drum programs
If you have selected "Drums" for Oscillator Mode (Prog 1–
1a) of a Program, the Use DKit Setting box (Prog 8–1c)
becomes available. For more information, please see next
diagram.
If you check this box, Bus (IFX/Output) Select, FX Control
Bus, Send1, and Send2 (Global 5–5b) for each key of the
selected Drum kit becomes effective. For example, you can
send a snare sound to IFX1 to apply the Gate effect, a kick
Insert Effects (IFX1–IFX5) Routing
sound to IFX2 to apply EQ, and other sounds to AUDIO
OUTPUT L/MONO and R without applying any Insert
Effects.
Tip: In most of the preloaded drum kits, the following types
of drum instrument have the same Bus (IFX/Output) Select
settings.
Snares → IFX1
Kicks → IFX2
Other → IFX3
If you de‐select the box, all drum instrument outputs are
sent to the bus specified by Bus (IFX/Output) Select (Prog
8–1b). You may apply any Insert Effects to all drum
instruments, regardless of the Drum kit settings.
Combination and Sequencer modes
Use Bus (IFX/Output) Select (Combi/Seq 8–1(2)d) for
timbres (Combination) and tracks (Sequencer) to select an
Insert Effect to apply to the corresponding timbres and
tracks. You can route multiple timbres and tracks to a single
Insert Effect.
Tip: You can use each timbre/track's Bus (IFX/Output)
Select, post‐IFX Chain to and Chain parameters (Combi/
Seq 8–3b) to create a variety of routings.
Example: Inserting one IFX into two or more timbres
Example: Inserting a separate IFX into each timbre, and inserting
another IFX later
Example: Sharing part of a timbre's IFX chain with another tim-
bre
As with Program mode, select L/R, IFX1–5, or Off for each
timbre and track.
Send1 (to MFX1) and Send2 (to MFX2) become available if
Bus (IFX/Output) Select has been set to L/R or Off. If you've
set Bus (IFX/Output) Select to IFX1–5, use Send1 and
Send2 (Combi/Seq 8–3b) following the insert effect to adjust
the send levels.
Send1 responds to CC#93, and Send2 responds to
CC#91. At this time, the actual send level uses the value
of the Send 1 and 2 settings for Oscillators 1 and 2 of the
Programs (selected for the timbres and tracks),
multiplied by the Send 1 and 2 values received via
MIDI.
The following diagram shows an example of Combination
mode. The Timbre 1 output is sent to IFX1 and the Timbre 2
output is sent to IFX2 according to the Bus (IFX/Output)
Select setting. Other timbres are sent to L/R. The output
signal passes through the TFX, then goes to AUDIO
OUTPUT L/MONO and R.
241