Global P2: Controllers; 2-1: Foot Controllers; 2-2: Midi Cc# Assign - Korg Krome Parameter Manual

Global mode

Global P2: Controllers

2–1: Foot Controllers
2–1a
2–1a: Foot Switch & Pedal/Damper
Foot Switch Assign
Selects the function that will be controlled by a pedal switch
(such as the optional Korg PS‐1 or PS‐3) connected to the
ASSIGNABLE SWITCH jack.
For a complete list of possible assignments, please see "Foot
Switch Assignments" on page 349.
Foot Pedal Assign
Selects the function that will be controlled by a foot volume
pedal (XVP‐10 or EXP‐2 option [sold separately]) connected
to the ASSIGNABLE PEDAL jack.
For a complete list of possible assignments, please see "Foot
Pedal Assignments" on page 350.
Damper Polarity
Set this to match the polarity of the damper pedal connected
to the DAMPER jack. If the polarity does not match,
operating the damper pedal will not produce the correct
result. If no damper pedal is connected, set this to (–) KORG
Standard.
(–) KORG Standard: Use this setting for "open‐type"
damper pedals, such as the optional Korg DS–1H.
(+): Use this setting for "closed‐type" pedals.
Foot Switch Polarity
Set this to match the polarity of the footswitch connected to
the ASSIGNABLE SWITCH jack. If the polarity does not
match, operating the damper pedal will not produce the
correct result. If no damper pedal is connected, set this to (–)
KORG Standard.
(–) KORG Standard: Use this setting for "open‐type"
footswitches, such as the optional Korg PS–1 or PS‐3.
(+): Use this setting for "closed‐type" pedals.
2–1: Menu Command
V
• 0: Write Global Setting
For more information, please see "Global: Menu Command"
on page 216.
202
2–1
Menu
[List of Foot Switch Assign]
[List of Foot Pedal Assign]
[(–) KORG Standard, (+)]
[(–) KORG Standard, (+)]
see p. 216
2–2: MIDI CC# Assign
2–2a
2–2a: ARP Controllers
This specifies the MIDI messages that will be transmitted
when you operate the ARP button or when you operate
knobs 1–4 with ARP selected by SELECT button.
Here, you can assign control change messages to the
arpeggiator switches and knobs 1–4 when ARP is selected
by the SELECT button.
When you operate a switch or knobs 1–4 when ARP is
selected by the SELECT button, the assigned control change
message will be transmitted from the MIDI OUT connector.
The assigned control change messages can also be received
from an external MIDI device connected to the MIDI IN
connector, and used to control the corresponding
arpeggiator.
The default settings of each parameter are as shown in the
display above.
(SW) – ARP (ON/OFF)
Assigns a control change message sent by the ARP button.
The default setting is CC#14.
(ARP CONTROL) GATE
Assigns the control change message sent by knob 1 when
ARP is selected by the SELECT swtich. The default setting is
CC#22.
(ARP CONTROL) VELOCITY
Assigns the control change message sent by knob 2 when
ARP is selected by the SELECT swtich. The default setting is
CC#23.
(ARP CONTROL) SWING
Assigns the control change message sent by knob 3 when
ARP is selected by the SELECT swtich. The default setting is
CC#24.
(ARP CONTROL) STEP
Assigns the control change message sent by knob 4 when
ARP is selected by the SELECT swtich. The default setting is
CC#25.
2–2: Menu Command
V
• 0: Write Global Setting see p. 216
• 1: Reset Controller MIDI Assign
For more information, please see "Global: Menu Command"
on page 216.
2–2
Menu
[Off, 000...119]
[Off, 000...119]
[Off, 000...119]
[Off, 000...119]
[Off, 000...119]
see p. 220