Dynamics (Dynamic); 000: No Effect; 001: Stereo Compressor; 002: Red Comp - Korg Krome Parameter Manual

Dynamics (Dynamic)

000: No Effect

Select this option when you do not use any effects. The
Insert Effect/Total Effect section outputs unprocessed
signals and the Master Effect section mutes the output.

001: Stereo Compressor

This effect compresses the input signal to regulate the level
and give a "punchy" effect. It is useful for guitar, piano, and
drum sounds. This is a stereo compressor. You can link left
and right channels, or use each channel separately.
Stereo In - Stereo Out
Left
EQ Trim
LEQ HEQ
Envelope - Control
Envelope Select
Envelope - Control
EQ Trim LEQ HEQ
Right
L/R Mix, Determines whether the left and
Envelope
a L/R Individ- right channels are linked or used
Select
ually separately
b Sensitivity 1...100 Sets the sensitivity
c
Attack 1...100 Sets the attack level
d EQ Trim 0...100 Sets the EQ input level
Selects the cutoff frequency (low
Low,
Pre LEQ Fc or mid-low) of the low-range
Mid-Low
equalizer
e
Selects the cutoff frequency
High,
Pre HEQ Fc (high or mid-high) of the high-
Mid-High
range equalizer
Pre LEQ Gain
–15.0...+15.0 Sets the gain of the Low EQ
[dB]
f
Pre HEQ Gain
–15.0...+15.0 Sets the gain of the High EQ
[dB]
Sets the output level of the
Output Level 0...100
compressor
Selects the modulation source
g Src Off...Tempo
for the compressor output level
Sets the modulation amount for
Amt –100...+100
the compressor output level
Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects a modulation source for
h Src Off...Tempo
Wet/Dry
Sets the modulation amount for
Amt –100...+100
Wet/Dry
a: Envelope Select
This parameter selects whether the left and right channels
are linked to control both signals simultaneously, or whether
each channel is controlled independently.
b: Sensitivity
g: Output Level (Level)
The Sensitivity parameter sets the sensitivity of the
compressor. If this parameter is set to a higher value, lower
level sounds will be boosted. With a higher Sensitivity, the
overall volume level is higher. To adjust the final volume
level, use the Output Level parameter.
Wet / Dry
Compressor
Output Level
Output Level
Compressor
Wet / Dry
Dynamics (Dynamic) 000: No Effect
Level
Wet
Dry
c: Attack
This parameter controls the attack level.
Level
Attack=80
Attack=20
Dry

002: Red Comp

When playing chords on an electric piano or similar
instrument, it's helpful to use a compressor to keep each
note smooth and well‐balanced. In addition to a distinctive
percussive accent, it will also provide a long sustain. This
effect models a popular compressor with a clean sound
that's perfect for pop and funk music.
Wet: Mono In - Mono Out / Dry: Stereo In - Stereo Out
Left
+
Compressor
Envelope - Control
Right
a Sensitivity 1...100 Sets the sensitivity
b Attack 1...100 Sets the attack level
Sets the output level of the
Level 0...100
compressor
Selects the modulation source
c Src Off...Tempo
for Level
Sets the modulation amount for
Amt –100...+100
Level
Dry, 1 : 99... Sets the balance between the
Wet/Dry
99 : 1, Wet effect and the dry input
Selects the modulation source
d Src Off...Tempo
for Wet/Dry
Sets the modulation amount for
Amt –100...+100
Wet/Dry
Compressor - Sensitivity
Sensitivity=100
Sensitivity=40
Time
Compressor - Attack
Wet
Time
Wet / Dry
Output Level
Wet / Dry
p.251
p.251
p.251
251