Korg Krome Parameter Manual page 110

Combination mode
About the Bus (IFX/Output) Select (Combi 8–1(2)d, 8–3b)
setting
• Regardless of the IFXs used, MFXs, and TFX settings, will
be set to DKit if the copy‐source program's Use DKit
Setting is checked. In conjunction with this, the Drum Kit
IFX Patch setting will be reset to the default setting.
• If IFXs is checked, the Bus (IFX/Output) Select setting of
the copy‐source program will be copied. If the copy‐
destination timbre Bus (IFX/Output) Select was set to
IFX1–IFX5, it will automatically be set to L/R. If you check
IFX-All used, the routing will be automatically set to
match the copy‐source program.
• If IFXs used is unchecked, then the copy‐source Bus (IFX/
Output) Select setting will be ignored. or if the Bus (IFX/
Output) Select of the copy‐source program and copy‐
destination timbre is set to IFX1–IFX5, it will
automatically be set to L/R.
3. If you check "Arp," the Program's arpeggiator settings
will also be copied.
If this is On (checked), the arpeggiator settings of the copy‐
source program will be copied to the "Arp" you specify in
step 8, and that arpeggiator's Arpeggiator Run setting will
be turned on and assigned to the copy‐destination timbre
("Arpeggiator Assign").
4. If you check "with Drum Track," the Drum Track Pat-
tern settings of the copy-source program will also be
copied.
If this is On (checked), the Drum Track Pattern settings of
the copy‐source program will be copied to the "Drum
Track" you specify in step 9.
The MIDI channel specified for the Drum Track copy‐
destination timbre will be used.
5. Use the To field to specify the copy-destination timbre.
The parameters for each timbre will be initialized. The copy‐
source program will be assigned to Program (see "0–1(2)b:
Program Select" on page 72).
• The MIDI Channel (Combi 3–1(2)c) setting will not
change if "Arp" is checked. If "Arp" is unchecked, MIDI
Channel will be automatically set to G ch.
• The Bank Select (When Status=EX2) (Combi 3–1(2)c)
setting will not change.
• The Status (Combi 3–1(2)c) setting will automatically be
set to INT.
• The P1: Basic/Controllers– Controllers Setup settings of
the copy‐source program will be copied.
6. Use the "Arp" field to select the copy-destination
arpeggiator; either A, B, C, or D.
7. Use the "Drum Track" to specify the destination timbre
to which the drum track program will be copied.
102
Copy Tone Adjust
This command replaces the Tone Adjust settings of the
selected Timbre (Combination mode) or Track (Sequencer
mode) with those of any other Program, Timbre, or Track.
1. Select the Timbre (Combination mode) or Track
(Sequencer mode) whose Tone Adjust settings you
want to replace.
For a timbre, access the Combi P0: Play– Tone Adjust page,
and select the Timbre.
For a track, access the Seq P0–2: Play/REC– Tone Adjust
page, and select the Track.
2. Select "Copy Tone Adjust" to open the dialog box.
3. Use the From field to select the Program, Combination,
or Song from which to copy.
You can also use the front‐panel BANK buttons to select the
desired bank.
4. If you've selected a Combination or Song, select a spe-
cific Timbre or Track as well.
5. Choose either All or Assignments Only to select the
Tone Adjust parameters that you want to copy.
All: This copies both the Tone Adjust parameter
assignments and values.
Assignments Only: This copies only the Tone Adjust
parameter assignments, without the values.