Telemetry Data Display - GRAUPNER HoTT MC-16 Series Programming Manual

Telemetry data display

mc-16
The HoTT transmitter features a single
screen below the aerial socket which is used both for
operating the transmitter and also to display telemetry
data in graphic form. You can switch between the two
operating modes by pressing one of the Select but-
tons  or  of the left-hand four-way button in
the base display.
mc-20
The HoTT transmitter has two independent
displays; a display for operating the transmitter and a
display just below the antenna socket for the graphic
display of telemetry data. This display is activated au-
tomatically as soon as the transmitter receives telem-
etry data from the receiver via the return channel.
Stp
#01 Flt
4.1V
0:00h M
x
If however, at the lower edge of the base display, only
"X" – as shown in the figure above – is displayed at two
locations instead of " ", then the telemetry display
will show the warning ...
C A N ' T
R E C E I V E
D ATA
O K
mc-20
..., on the front screen of the
placed shortly afterwards by the Graupner/SJ logo
and the transmitter name ...
mc20
..., and this means that there is no receiver within
38 Transmitter description - Telemetry data display
range capable of exploiting the telemetry link. Switch
on the model's receiver system or bind a receiver to
the active model memory as described in detail on
page 87 or 95.
#01
0:01h
If a telemetry link is present, the front screen of the
mc-20
HoTT shows the "Receiver" display by
default. The same occurs on the
0:00
mitter after you select the Telemetry display mode ...
0:00
HoTT
0.0V
... which is described in more detail in a section by
the same name on the next page.
Sensor Select
Up to four sensors can be connected, in any combi-
nation, to a telemetry-capable receiver. However, the
data output by these sensors must be (as described
HoTT, dis-
on page 252) selected in the »SENSOR SELECT«
sub-menu of the »Telemetry« menu ...
RECEIVER
GENERAL MODULE
ELECTRIC AIR.MOD
VARIO MODULE
GPS
... in order to activate their display. This data from the
Stp 0:00
Flt 0:00
4.1V HoTT
M 4.8V
mc-16
HoTT trans-
RX–S QUA: 100%
RX–S STR: 100%
RX–dBm: –33dBm
TX–dBm: –33dBm
L–PACK: 10ms
RX–VOLT:4.8V TMP
R–LOW V:4.6V +22°C
SENSOR SELECT
selected sensors is then appropriately prepared for
illustration by the graphic indicators as described be-
low. You must also ensure that the receiver selected
in the "Telemetry receiver" line of the »Telemetry«
menu (Bind 1 or 2) is the one to which the sensors
are connected; see pages 87 and 95. If you
select the "wrong" receiver, the "Receiver" display will
only show the data from that unit.
Furthermore, only sensors activated in the »SET-
TING & DATAVIEW« sub-menu of the »Telemetry«
menu, beginning page 241, according to the instruc-
tions included with the given sensor will be respon-
sive.
To switch between the screens for activated sensors
in the »SENSOR SELECT« sub-menu of the »Tele-
metry« menu, tap briefly on one of the  selection
keys of the left or right four-way button ...
RECEIVER
GENERAL
ELECT. AIR
VARIO
GPS
AIR ESC
... and, after the selected screen has been displayed,
use one of the  two keys to select the line of the
desired sensor. If no sensor is activated, then all dis-
play lines and sensors described in the next column,
except for the "RECEIVER" line, are blended out of
the display and the selection list:
RECEIVER
The selection can be confirmed right away by activat-
ing the center SET key of the right four-way button or