GRAUPNER HoTT MC-16 Series Programming Manual page 135

Roll ––– 100%
M o v e d e s i r e d s w i t c h
t o O N p o s i t i o n
( e x t . s w i t c h : S E T )
nor mal
SEL
If necessary, this may also be one of the transmitter
control switches C1 ... C4 or C1i ... C4i or one of the
logical switches L1 ... L8 or L1i ... L8i from the list of
"expanded switches".
The switch so assigned appears on the display, to-
gether with a switch icon that indicates the switch's
switching direction.
In the case of "C" or "L" switches, the stick or another
transmitter control or a certain switching logic can
itself be used as a switch. However, such a control
switch must have been appropriately defined in the
»Control switch« menu, see page 145, and a
logical switch must have been appropriately defined
in the »Logical switch« menu, see page 148 – pro-
vided that this menu point is unlocked (available) on
the transmitter concerned.
Whichever switch has been assigned ... the respec-
tive switch will appear in the display together with a
switch symbol indicating the switch's direction if actu-
ated, e. g. in the «Normal» flight phase.
Roll 3 100%
Nick ––– 100%
Tail ––– 100%
DUAL
nor mal
SEL
Once the value field has been activated with a brief
tap on the SET key of the right four-way button, use
the selection keys of the left or right four-way button
to move into the Dual-Rate value column labeled SEL
at the bottom edge of the display in order to separate-
ly change the dual-rate values shown in inverse video
for each of the two switch positions:
Roll 3 111%
Nick ––– 100%
Tail ––– 100%
DUAL
normal
SEL
Roll 3 88%
Nick ––– 100%
Tail ––– 100%
DUAL
normal
SEL
At the same time, the Dual-Rate curve will be pre-
sented in the graph.
A simultaneous tap on the  or  keys of the
right four-way button (CLEAR) will reset a changed
entry field value displayed in inverse video back to
"100 %".
Caution:
For safety reasons, Dual Rate value settings should
not be less than 20 %.
Some examples of Dual Rate values:
Dual Rate = 100% Dual Rate = 50%
Stick deflection Stick deflection
Exponential-Funktion
If you wish to program the Expo function, use the
 button of the left or right-hand four-way button to
move to the right, beyond the Dual Rate value col-
umn, until the word "EXPO" is displayed in the centre
of the screen instead of "DUAL":
Roll
Nick
Tail
nor mal
If a switchover between two variants is desired, as-
sign a switch in the column labeled with the
switch symbol (as described in the section "Physical
control, switch and control switch assignments" on
page 68):
Roll –––
M o v e d e s i r e d s w i t c h
t o O N p o s i t i o n
( e x t . s w i t c h : S E T )
nor mal
If necessary, this may also be one of the transmitter
control switches C1 ... C4 or C1i ... C4i or one of the
logical switches L1 ... L8 or L1i ... L8i from the list of
Dual Rate = 20%
"expanded switches".
The switch so assigned appears on the display, to-
gether with a switch icon that indicates the switch's
switching direction.
In the case of "C" or "L" switches, the stick or another
transmitter control or a certain switching logic can
Stick deflection
itself be used as a switch. However, such a control
switch must have been appropriately defined in the
»Control switch« menu, see page 145, and a
logical switch must have been appropriately defined
in the »Logical switch« menu, see page 148 – pro-
Program description - Dual Rate / Expo | Helicopter models
––– 0%
––– 0%
––– 0%
EXPO
SEL
0%
SEL
135