Table of Contents
Advertisement
tion "Physical control, switch and control switch as-
signments" on page 68, the left proportional slider
in the middle console to, for example:
In6
PH
Lv1
–––
In7
GL
fr
–––
In8
GL
Cn1
–––
In9
GL
–––
8
Thermal
typ
SEL
This control will allow the ailerons (2 + 5) and camber
flaps (6 + 7) to be continuously adjusted (as camber
flaps) with a mixer ratio yet to be set via the »Wing
mixers« menu.
If you assign the still free second three-stage switch
to Input 6 instead, you can call three different FL posi-
tions of the ailerons (AIL) and camber changing flaps
(FL) as well as three elevator positions (Elev) in the
"Thermal" flight phase, see the following page. (These
three switch positions correspond to the center posi-
tion and the two limit positions of the previously men-
tioned proportional rotary control.)
Note:
The FL and AIL flap positions in the two limit switch
positions or in the switch center depend on the value
set in the column "- trv +" as well as the offset value
and the mixer proportion set in the "Multi-flap menu"
of the »Wing mixers« menu, see further below.
Leave the (control) "- trv +" at its standard symmetric
settings of +100 % and the offset value at 0 %. Speci-
fying a symmetric or asymmetric time for smooth
switching between the three switch positions – in the
example "1.2 s 1.2 s" – in the column "- time +" is rec-
ommended:
306 Programming examples - Using flight phases
In6
In7
In8
In9
0%
Thermal
0%
0%
0%
In the "Multi-flap menu" of the ...
offset
»Wing mixers«
... menu, subsequently change only the values for
"FL.pos" and "FL" in the «Thermal» flight phase:
•
FL.pos
It is here that AILE and FLAP positioning takes
place during the «Thermal» flight phase in the
event that the assigned control (proportional con-
trol or 3-way switch) is in its neutral or middle po-
sition:
FL
•
Enter in this line the share of influence for ailer-
on and camber flap servos, when used as cam-
ber flaps, is to be produced by the selected control
(see above) or 3-way switch. Be sure to set these
values low enough that the flaps can be controlled
with appropriate sensitivity, for example:
1.2s
1.2s
0.0s
0.0s
0.0s
0.0s
0.0s
0.0s
– time +
(beginning on page 170)
AI
+100%
Ail-tr
+100%
Diff.
+55%
fl.pos
–9%
Thermal
AILE
Ail-tr
+100%
Diff.
+55%
fl.pos
–9%
FL
+10%
+10%
Thermal
AILE
Ail-tr
+60%
Diff.
+33%
fl.pos
–14%
FL
+15%
Thermal
FLAP
A simultaneous tap on the or key combina-
tion of the right four-way button (CLEAR) will reset
changed values back to their standard default values.
Note:
Due to the improved lift distribution, the degree of
mix ratios should be set so that the camber flaps are
slightly "lower" than the ailerons.
With a simultaneous tap on the keys of the left
four-way button, the reaction of the AILE and FLAP
servos can be checked in the »Servo display« by ac-
tuation of the selected camber flap control. (Push the
C1 stick to the front position so that the "AILE" and
"FLAP" positions can be better followed on actuation
of the corresponding control.)
Caution:
With aileron actuation the bars of the »Servo dis-
play« move in the same manner, for camber flap
actuation they will move in the opposite manner.
•
In the control's middle position, the – exam-
ple's – "FL-pos." setting only has a -9 % effect for
the AI and -11 % for the FL.
•
In one transmitter control end-position, AILE and
FLAP are again closer to the neutral position
because the mix ratio specified in the example
reduces the FL.pos setting, whereas ...
•
... in the other limit position, AILE and FLAP reach
the maximum downward offset prescribed by the
mixer percentage.
In order to set a – corrective – admix for the eleva-
tor, exit the "Multi-flap menu" and return to the base
screen of the »Wing mixers« menu:
+15%
Advertisement
Table of Contents
