GRAUPNER HoTT MC-16 Series Programming Manual page 259

Multichannel 1
INPUT1 fr –––
INPUT2 fr –––
INPUT3 fr –––
INPUT4 fr –––
SEL
... and „MC2" (Multichannel 2) ...
Multichannel 2
INPUT1 fr –––
INPUT2 fr –––
INPUT3 fr –––
INPUT4
fr –––
INPUT5 fr –––
INPUT6 fr –––
INPUT7 fr
–––
INPUT8 fr –––
SEL
Column 2 "Control"
Multichannel 1
INPUT1 fr –––
INPUT2 fr –––
INPUT3 fr –––
INPUT4 fr –––
SEL
Use the arrow keys to move to the column over SEL.
After completing the activation of transmitter control
assignment by tapping the center SET
four-way button, the message shown below will ap-
pear in the display:
Multichannel 1
IN
Move desired
IN
control adj.
IN
INPUT4 fr –––
SEL
Now operate the transmitter control you wish to use:
the information window closes, and instead the Value
0%
field displays the name of the transmitter control you
0%
have chosen.
0%
0%
Note:
offset
If you are using the Nautic-Expert switch module,
Order No. 4159, any proportional controls you assign
act like switches when close to their end-points.
Column 3 "Switch"
0%
0%
0%
M o v e d e s i r e d s w i t c h
0%
t o O N p o s i t i o n
0%
( e x t . s w i t c h : S E T )
0%
INPUT4
0%
0%
offset
This column is used to assign each of the inputs
used, 1 through 8 (maximum), to any switch available
on the transmitter. These assignments are done as
described in the section „Physical control, switch and
control switch assignments" on page 68:
0%
Any controls which were previously assigned in the
0%
0% second column will be erased. In this case, instead of
0% SEL, the switch symbol
offset
bottom of the 2nd column such that now a second
"normal" switch, or even a transmitter control switch,
logical switch, ... can be assigned as needed from
the group of "expanded switches". In general it is suf-
key of the right
ficient to assign a simple switch or transmitter control.
INPUT1
INPUT2
0%
INPUT3
0%
INPUT4
0%
0%
offset
Multichannel 1
fr ––– 0%
SEL offset
will be displayed at the
Multichannel 1
––– 2 0%
fr ––– 0%
fr ––– 0%
fr ––– 0%
offset
Erasing transmitter controls or switches
With transmitter control / switch assignment active,
simultaneously pressing the  or  buttons of
the right-hand four-way button (CLEAR) – see screen-
shots above – resets the corresponding input to "fr"
and "---".
Column 4 "offset"
Multichannel 1
INPUT1 3 2
INPUT2 fr –––
INPUT3 fr –––
INPUT4 fr –––
The control center for the given control, i. e. its zero
point, can be changed in this column. The adjustment
range lies between -100 % and +100 %.
Simultaneously tapping on the  or  keys of
the right four-way button (CLEAR) will reset the value
displayed in inverse video back to its "0 %" value.
Note:
Leave the offset setting at 0 % while making switch
assignments.
Column 5 „– travel +"
To adjust servo travel, move to the right, beyond the
"Offset" column, following the right-pointing arrow in
the bottom left-hand corner of the screen:
Multichannel 1
INPUT1 +100%
+100%
INPUT2 +100% +100%
INPUT3 +100% +100%
INPUT4
+100% +100%
– travel +
Finally, transmitter control travel is set for both sides
in the column "-travel+". The range for this lies be-
tween -100 % and +100 %. This is accomplished by
Program description - Multichannel
0%
0%
0%
0%
offset
259