Table of Contents
Advertisement
Base setup model
Mod.name
ST R ET
Stick mode
module
HoTT
bind
Rcv Ch Map
R12
... which must be assembled from characters avai-
lable on the second page of the "Model name" line:
! " # $ % & ' ( ) + , – . / 0 1 2 3
4 5 6 7 8 9 : ;
? @ A B C D E
F G H I J K
L
M N O P Q R S T U V W X
Y Z [ ¥ ] ^ _ ` a b c d e f g h i j k
Mod Name
STARL
After entering the "Model name", the settings adopt-
ed from »Basic settings« for "Stick mode" and "DSC
Output" are to be checked and changed as neces-
sary for the given memory location.
Another option is to be activated in the "Autorotation"
line. Even if you are not an advanced pilot, the autoro-
tation switch should at least be set as an emergency
shutoff switch for the motor.
Do this by selecting the "Autorotation" line with a
brief tap on the center
SET
key of the right touch
pad, activate the switch assignment, assign a 2-way
switch, e. g. "7", and put it in its "ON" position:
Base setup model
RF transmit
RF Range Test
DSC Output
Autorotation
The selected switch should be in a location on the
transmitter which is easily within reach – without let-
ting loose of a stick – e. g. above the pitch stick.
320 Programming examples - Helicopter models
Note:
More more information about the setting of this
"emergency shutoff", see further in this section.
1
n/a
Another tip:
n/a
Make a habit of giving all switches a common switch-
on direction; then a quick glance over the transmitter
prior to the flight should suffice – all switches off.
Setting options for the "Autorotation C1 position",
"Motor stop" and "Stick warning" are not yet of par-
ticular interest ...
... and you should only leave or set the "Auto timer
reset" line to "yes" if you actually want the timers to
be reset to the appropriate initial value every time you
switch the transmitter on.
Additional settings specific to helicopters are made in
the menu ...
»Helicopter type«
In the "Swashplate type" line, select control for
swashplate or pitch function. In this example:
"3Sv(2rol)".
The "Linearis. swashpl." line is not yet of interest.
In the "Rotor direction" line, it is established whether
the rotor – as viewed from above – turns to the right
(clockwise) or left (counter-clockwise). In other words,
whether it rotates counterclockwise or clockwise. In
this example "right".
Check the default for "Pitch min", which was adopted
from »Basic settings«, to confirm that the entry
ON
"front" or "rear" is in keeping with personal prefer-
99sec
ences or should be changed:
PPM10
7I
(page 108)
Heli type
Swashplate
3Sv(2rol)
Linear. swashpl.
no
Rotor direct
right
Pitch min.
back
SEL
"Expo throttle lim." in the bottom line of this display,
are currently of no interest.
By now, the servos should be plugged into the recei-
ver in the intended sequence:
Free or aux. function
Free or aux. function
Free or speed governor or aux. function
Free or aux. function
Receiver power supply
Gyro gain
Throttle servo or speed controller
Free or aux. function
Tail rotor servo (gyro system)
Pitch-axis 1 servo
Roll 1 servo
Collective pitch or roll 2 or
Pitch-axis 2 servo
Receiver power supply
Free or aux. function
Note:
Please note that on the newer Graupner-mc- and
mx- remote control systems, the first pitch servo and
the throttle servo are swapped in comparison to some
older systems.
Mix ratios and mix directions for swashplate pitch, roll
and nick servos are already pre-adjusted to +61 % in
the menu ...
»Swashplate mixer«
Swashplate mixer
Pitch
+61%
Roll
+61%
Nick
+61%
SEL
If the swashplate mixer should not follow stick move-
ments properly, first change the mixing directions
from "+" to "-" before changing servo directions in the
(page 220)
Advertisement
Table of Contents
