Table of Contents
Advertisement
"Mode" column
Base setup model
Mod.name
GRAUBELE
Stick mode
module
SP.
1
SP channel
Mod
In this column you select the transmission mode of
the external RF module:
•
Mode "1":
2-channel hopping
•
Mode "2":
x-channel hopping
"BIND" column
Base setup model
Mod.name
GRAUBELE
Stick mode
module
SP.
1 BIND
SP channel
Mod
The "BIND" column in the right-hand column can
be used to initiate the "Bind" process of the non-
Graupner|SJ system – the transmitter's RF section
must be switched off when the transmitter is first
switched on.
Important notes:
•
The output voltage of the DATA socket is
around 5 V, and must be reduced to the pow-
er supply voltage generally required by exter-
nal digital RF modules (3 to max. 3.3 V). This is
accomplished using the circuit which is shown
here in diagrammatic form:
DATA S
Vcc IN = 5 V
DATA +
1
22µF/6.3 V
BIND
6
DATA -
BD
•
Servo travels must be limited to max. 128 %.
SP channels
Note:
This menu line is suppressed in the "Module" line if
you select "HoTT" or "EXT.".
If necessary, use the Select buttons of the left or
right-hand four-way button to move to the "SP chan-
nels" line, then briefly press the central
1
the right-hand four-way button to activate the Value
window:
6
BD
Mod.name
Stick mode
module
SP channel
You can now select "6" or "8" channels using the right-
hand Select buttons. The procedure is concluded by
again pressing the central
hand four-way button.
At the transmitter this selection only affects the num-
ber of control channels transferred to the external RF
module via the DATA socket. If you choose "6", then
these are control channels 1 ... 6; if you choose "8",
these are channels 1 ... 8.
Simultaneously pressing the or buttons of
the right-hand four-way button (CLEAR) returns the
display to "6".
125000 baud signal
Vcc OUT = 3 ... 3.3 V
Vcc
Low Drop
Voltage
SP.-MODULE
Regulator
22µF/6.3 V
with
GND
digital input signal
GND
SET
button of
Base setup model
GRAUBELE
1
SP.
1 BIND
6
SEL
SET
button of the right-
Program description - Base setup models | Winged models
EXT. PPM signal
Note:
This menu line is suppressed in the "Module" line if
you select "HoTT".
Base setup model
Mod.name
GRAUBELE
Stick mode
module
EXT.
PPM10
EXT.PPM sig.
Some RF modules which can be connected to the
DSC connector require an inverted input signal. Be
sure to follow the respective module's installation
instructions for this.
The choice of "inverted" instead of the default preset
"normal" allows for appropriate adaptation of the pro-
vided PPM signal.
A simultaneous tap on the or keys of the
right four-way button (CLEAR) will reset the display to
"normal".
Receiver channel mapping
Note:
This menu line is suppressed in the "Module" line if
you select "EXT." or "SP.".
As long as there is at least one "bound" HoTT receiv-
er in the "Module" line, the next line down will be the
"Rcv Ch map" line:
Base setup model
Mod.name
GRAUBELE
Stick mode
module
HoTT
bind
Rcv Ch Map
R12
SET
As already mentioned in the introduction to the sec-
mc-16
tion entitled "Binding receivers",
1
normal
SEL
1
bind
R08
SET
HoTT and
89
Advertisement
Table of Contents
