Santerno DCREG2 Series User Manual page 7

DCREG2
DCREG4
7.3.38 C143: Alarm A028 Trip Delay ......................................................................................... 180
7.3.39 C150: Alarm A001 Trip Disabling ................................................................................... 180
7.3.40 C151: Alarm A004 Trip Disabling ................................................................................... 180
7.3.41 C153: Alarm A006 Trip Disabling ................................................................................... 180
7.3.42 C154: Alarm A007 Trip Disabling ................................................................................... 181
7.3.43 C155: Alarm A008 Trip Management ............................................................................. 181
7.3.44 C156: Alarm A010 Trip Disabling ................................................................................... 181
7.3.45 C157: Alarm A016/017 Trip Disabling ............................................................................ 181
7.3.46 C158: Alarm A027 Trip Disabling ................................................................................... 181
7.3.47 C159: Alarm A028 Trip Disabling ................................................................................... 182
7.3.48 C160: Serial Connection Drive Address ......................................................................... 182
7.3.49 C161: Serial Connection Transmission Speed ............................................................... 182
7.3.50 C162: Serial Connection Parity Control .......................................................................... 182
7.3.51 C163: Master Data Area Base Address.......................................................................... 183
7.3.52 C164: Serial Time Out .................................................................................................... 183
7.3.53 C165: Serial Response Delay ......................................................................................... 183
7.3.54 C170: Load Type ............................................................................................................ 183
8 DIAGNOSTICS ................................................................................................................................ 184
8.1 ALARM PARAMETERS .......................................................................................................... 184
8.1.1 A001: Field Current Failure ................................................................................................. 185
8.1.2 A002: Heatsink Overtemperature ....................................................................................... 185
8.1.3 A003: Armature Overcurrent ............................................................................................... 185
8.1.4 A004: Load Loss ................................................................................................................. 185
8.1.5 A006: Unstable Mains Frequency ....................................................................................... 185
8.1.6 A007: Mains Phase Failure ................................................................................................. 186
8.1.7 A008: Speed Feedback Failure........................................................................................... 186
8.1.8 A009: Field Overcurrent ...................................................................................................... 186
8.1.9 A010: Armature Overvoltage............................................................................................... 186
8.1.10 A011: Auto Tuning Inductance out of Range .................................................................. 186
8.1.11 A012: Mains Frequency out of Range ............................................................................ 186
8.1.12 A013: Synchronization Failure ........................................................................................ 187
8.1.13 A014: AutoTuning Resistance out of Range................................................................... 187
8.1.14 A015: Torque During Current AutoTuning ...................................................................... 187
8.1.15 A016: Mains Overvoltage ............................................................................................... 187
8.1.16 A017: Mains Undervoltage ............................................................................................. 187
8.1.17 A018: AutoTuning Interrupted ......................................................................................... 188
8.1.18 A019: Limitation During Speed AutoTuning .................................................................... 188
8.1.19 A020: ExternalAlarm 1 .................................................................................................... 188
8.1.20 A021: Motor Thermal Protection Trip ............................................................................. 188
8.1.21 A022: Drive Thermal Protection Trip .............................................................................. 188
8.1.22 A023: Field Weakening Min. Current Limit ..................................................................... 188
8.1.23 A024: EEPROM Missing or Blank .................................................................................. 189
8.1.24 A025: Wrong Parameters in EEPROM Work Area ........................................................ 189
8.1.25 A026: EEPROM Wrong Backup Parameters ................................................................. 189
8.1.26 A027: Serial Communication Failure .............................................................................. 189
8.1.27 A028: Connection with Field Bus Failure ........................................................................ 189
8.1.28 A029: External Alarm 2 ................................................................................................... 190
8.1.29 A030: External Alarm 3 ................................................................................................... 190
8.1.30 A031: EEPROM Work Area Internal Data Altered .......................................................... 190
8.1.31 A032: Microcontroller Reset ........................................................................................... 190
8.1.32 A033: Unknown Failure .................................................................................................. 190
8.1.33 Additional Alarms ............................................................................................................ 190
8.2 WARNING PARAMETERS ..................................................................................................... 191
8.2.1 W002: Speed Feedback Loss ............................................................................................. 191
8.2.2 W003: Hardware Limit Current not at Maximum Value ..................................................... 191
8.2.3 W004: Safe Restart after an Alarm Reset .......................................................................... 191
8.2.4 W005: Restart after an Emergency Stop from Keypad ....................................................... 191
8.2.5 W006: Backup Values Stored in RAM ................................................................................ 192
8.2.6 W007: Default Values Stored in RAM ................................................................................. 192
8.2.7 W008: Wrong parameters in EEPROM Work Area ............................................................ 192
8.2.8 W009: Wrong Parameters in EEPROM Backup Area ........................................................ 193
9 EMC CHARACTERISTICS AND INPUT FILTER ............................................................................ 194
15P0059B3
USER MANUAL
7/200