Omron NJ Series Troubleshooting Manual page 89

Event code Event name
54015422 hex Target Velocity
Setting Out of
Range
54015423 hex Acceleration Set-
ting Out of Range
54015424 hex Deceleration Set-
ting Out of Range
54015425 hex Jerk Setting Out of
Range
54015427 hex Torque Ramp Set-
ting Out of Range
54015428 hex Master Coefficient
Scaling Out of
Range
54015429 hex Slave Coefficient
Scaling Out of
Range
5401542A hex Feeding Velocity
Setting Out of
Range
5401542B hex Buffer Mode Selec-
tion Out of Range
5401542C hex Coordinate System
Selection Out of
Range
5401542D hex Circular Interpola-
tion Mode Selec-
tion Out of Range
5401542E hex Direction Selec-
tion Out of Range
5401542F hex Path Selection Out
of Range
54015430 hex Position Type
Selection Out of
Range
NJ-series Troubleshooting Manual (W503)
Meaning
The parameter specified for • Instruction input
the Velocity input variable
to a motion control instruc-
tion is out of range.
The parameter specified for • Instruction input
the Acceleration input vari-
able to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the Deceleration input vari-
able to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the Jerk input variable to a
motion control instruction is
out of range.
The parameter specified for • Instruction input
the TorqueRamp input vari-
able to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the MasterScaling input
variable to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the SlaveScaling input vari-
able to a motion control
instruction is out of range.
The parameter specified for • The Feed Velocity
the FeedVelocity input vari-
able to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the BufferMode input vari-
able to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the CoordSystem input
variable to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the CircMode input variable
to a motion control instruc-
tion is out of range.
The parameter specified for • Instruction input
the Direction input variable
to a motion control instruc-
tion is out of range.
The parameter specified for • Instruction input
the PathChoice input vari-
able to a motion control
instruction is out of range.
The parameter specified for • Instruction input
the ReferenceType input
variable to a motion control
instruction is out of range.
Assumed cause
Maj Prt
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
(input variable Feed-
Velocity) is still at the
default (0).
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
parameter exceeded
the valid range of the
input variable.
3 Error Tables
Level
Refer-
ence
Min Obs Info
S NJ-series
Instruc-
tions Ref-
erence
Manual
(Cat. No.
W502)
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
S Same as
above.
3-27
3