Mitsubishi Electric Melsec Q Series User Manual page 316

Local FDL address display area . . . . . . . . . . . . . 3-22
Local station error information area . . . . . . . . . . 3-21
Local station information area . . . . . . . . . . . . . . 3-21
[M]
Master parameters . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Max. bus cycle time . . . . . . . . . . . . . . . . . . . . . . 3-44
Min. bus cycle time . . . . . . . . . . . . . . . . . . . . . . . 3-44
Module READY signal (X1D) . . . . . . . . . . . . . . . 3-16
[O]
Offline test status area . . . . . . . . . . . . . . . . . . . . 3-22
Operation mode change area . . . . . . . . . . . . . . . 3-23
Operation mode change completed signal (X11)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-14
Operation mode change request area . . . . . . . . 3-23
Operation mode change request signal (Y11) . . 3-14
Operation mode change result area . . . . . . . . . . 3-23
Operation mode setting . . . . . . . . . . . . . . . . . . . . 6-4
Operation mode signal (X10) . . . . . . . . . . . . . . . 3-13
Output data area (for mode 3) . . . . . . . . . . . . . . 3-26
Output data start address area (for mode 3) . . . 3-28
Output status setting for the case of a CPU stop error
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-23
[P]
Parameter setting . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Parameter setting status area (Active station) . . 3-33
Parameter setting status area (Reserved station)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-33
Performance specifications . . . . . . . . . . . . . . . . . 3-1
Pin assignments of the PROFIBUS interface
connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-9
Processing Time . . . . . . . . . . . . . . . . . . . . . . . . . 3-59
PROFIBUS cable . . . . . . . . . . . . . . . . . . . . . . . . 5-10
PROFIBUS-DP network configuration . . . . . . . . . 2-5
PROFIBUS-DPV0 Functions . . . . . . . . . . . . . . . . 4-2
PROFIBUS-DPV1 Functions . . . . . . . . . . . . . . . 4-11
PROFIBUS-DPV2 Functions . . . . . . . . . . . . . . . 4-16
[Q]
QJ71PB92D-compatible function . . . . . . . . . . . . 4-38
[R]
READ services (Class1_SERVICE,
Class2_SERVICE) . . . . . . . . . . . . . . . . . . . . . . . 7-17
Redundant system support function . . . . . . . . . . 4-28
Restart request signal (Y0D) . . . . . . . . . . . . . . . 3-13
[S]
Self-diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
Serial No. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-16
Slave parameters . . . . . . . . . . . . . . . . . . . . . . . . 6-10
Slave status area . . . . . . . . . . . . . . . . . . . . . . . . 3-29
Slave status area (Alarm detection) . . . . . . . . . . 3-35
Slave status area (Diagnostic information detection)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-32
INDEX
- 2
Slave status area (Normal communication detection)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-30
Slave status area (Reserved station setting status)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-31
Standby master FDL address display area. . . . . 3-55
System switching . . . . . . . . . . . . . . . . . . . . . . . . 4-30
System switching condition setting area
(Disconnected station detection) . . . . . . . . . . . . 3-56
System switching condition setting result area
(Disconnected station detection) . . . . . . . . . . . . 3-58
System switching error . . . . . . . . . . . . . . . . . . . . 4-30
System switching methods . . . . . . . . . . . . . . . . . 4-30
System switching time . . . . . . . . . . . . . . . . . . . . 3-65
System switching time in redundant system . . . . 3-65
[T]
Temporary slave reservation function. . . . . . . . . 4-26
Temporary slave reservation request area . . . . . 3-52
Temporary slave reservation status area . . . . . . 3-34
Time control area . . . . . . . . . . . . . . . . . . . . 3-51,3-52
Time control over DP-Slaves . . . . . . . . . . . . . . . 4-16
Time control setting request area . . . . . . . . . . . . 3-51
Time control setting response area . . . . . . . . . . 3-51
Time control start request signal (Y19) . . . . . . . . 3-16
Time control start response signal (X19) . . . . . . 3-16
Time data read request. . . . . . . . . . . . . . . . . . . . 7-50
Time data write request . . . . . . . . . . . . . . . . . . . 7-54
Time data write request (UTC format) . . . . . . . . 7-52
Transmission delay time . . . . . . . . . . . . . . . . . . . 3-63
Transmission distance . . . . . . . . . . . . . . . . . . . . . 3-2
[W]
Watchdog timer error signal (X1F) . . . . . . . . . . . 3-16
Wiring specifications for bus terminator . . . . . . . 5-11
WRITE services (Class1_SERVICE,
Class2_SERVICE) . . . . . . . . . . . . . . . . . . . . . . . 7-20