Cisco SCE 1000 Installation And Configuration Manual
Cisco SCE 1000 Installation And Configuration Manual

Cisco SCE 1000 Installation And Configuration Manual

2xgbe
Hide thumbs Also See for SCE 1000:
Table of Contents

Advertisement

Cisco SCE 1000 2xGBE Installation and
Configuration Guide
Release 3.8.x
September 17, 2012
Americas Headquarters
Cisco Systems, Inc.
170 West Tasman Drive
San Jose, CA 95134-1706
USA
http://www.cisco.com
Tel: 408 526-4000
800 553-NETS (6387)
Fax: 408 527-0883
Text Part Number: OL-26790-01

Advertisement

Table of Contents
loading

Summary of Contents for Cisco SCE 1000

  • Page 1 Cisco SCE 1000 2xGBE Installation and Configuration Guide Release 3.8.x September 17, 2012 Americas Headquarters Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 http://www.cisco.com Tel: 408 526-4000 800 553-NETS (6387) Fax: 408 527-0883 Text Part Number: OL-26790-01...
  • Page 2 OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and/or its affiliates in the U.S. and other countries. To view a list of Cisco trademarks, go to this URL: www.cisco.com/go/trademarks.
  • Page 3: Table Of Contents

    Information About The SCE Platform Front Panel Back Panel Information About Checking the Shipping Container Contents SCE 1000 Component List SCE 1000 Installation Checklist Information About Topology C H A P T E R Introduction Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 4 Airflow Site Requirements Installing the SCE 1000 Platform Installation Precautions How to Install the SCE 1000 on a Workbench or Tabletop What to Do Next Rack-Mounting a SCE 1000 Platform How to Attach the Brackets to the SCE 1000 How to Attach the Cross Rail Supports to the Rack...
  • Page 5 Step 5: Configuring the DNS Settings 5-12 Example 5-13 Step 6: Configuring the RDR Formatter Destination 5-13 Example 5-13 Step 7: Configuring Access Control Lists (ACLs) 5-13 Information About Access Control Lists 5-14 Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 6 Starting the SCE 1000 Platform Checking Conditions Prior to System Startup Performing Complex Configurations Starting the System and Observing Initial Conditions What to Do Next Final Tests How to Verify Operational Status Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 7 Copying the User Log to an External Source 8-14 How to Copy the User Log to an Internal Location 8-14 Viewing the User Log 8-15 Clearing the User Log 8-15 Viewing the User Log Counters 8-15 Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 8 External Optical Bypass Functionality External Optical Bypass Module Front Panel Specifications Installing the External Bypass Module How to Install the Module in a Rack How to Cable the External Optical Bypass Module Cisco SCE 1000 2xGBE Installation and Configuration Guide viii OL-26790-01...
  • Page 9 This guide contains instructions on how to install and run the SCE 1000 platform. This guide assumes a basic familiarity with telecommunications equipment and installation procedures. This introduction...
  • Page 10: About This Guide

    Change Summary OL-26790-01 Release 3.8.x First version of this document (new for the Release September 17, 2012 3.8.x train). No changes were made from the last release of the 3.7.x train. Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 11: Organization

    Chapter 4, “Installation and This chapter explains how to install an SCE 1000 Maintenance” platform in a rack or in a general tabletop installation and how to install or replace the power supply units and fan modules.
  • Page 12: Related Publications

    About this Guide Related Publications Your SCE 1000 platform and the software running on it contain extensive features and functionality, which are documented in the following resources: Cisco CLI software: • Cisco SCE 2000 and SCE 1000 Software Configuration Guide –...
  • Page 13: Conventions

    Means the described action saves time. You can save time by performing the action described in the paragraph. Warning Means reader be warned. In this situation, you might perform an action that could result in bodily injury. Cisco SCE 1000 2xGBE Installation and Configuration Guide xiii OL-26790-01...
  • Page 14: Obtaining Documentation And Submitting A Service Request

    Obtaining Documentation and Submitting a Service Request For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation, at: http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html...
  • Page 15 Revised: September 17, 2012, OL-26790-01 Introduction This chapter provides a general overview of the Cisco Service Control solution. It introduces the Cisco Service Control concept and the Service Control capabilities. It also briefly describes the hardware capabilities of the Service Control Engine (SCE) platform and the Cisco specific applications that together compose the total Cisco Service Control solution.
  • Page 16: Chapter 1 General Overview

    With the power of Service Control, service providers have the ability to analyze, charge for, and control IP network traffic at multigigabit wire line speeds. The Cisco Service Control solution also gives service providers the tools they need to identify and target high-margin content-based services and to enable their delivery.
  • Page 17: Cisco Service Control Capabilities

    Cisco Service Control Capabilities Cisco Service Control Capabilities The core of the Cisco Service Control solution is the purpose-built network hardware device: the Service Control Engine (SCE). The core capabilities of the SCE platform, which support a wide range of applications for delivering Service Control solutions, include: •...
  • Page 18: Sce Platform

    – Programmable system core for flexible reporting and bandwidth control • Transparent network and BSS/OSS integration into existing networks • Subscriber awareness that relates traffic and usage to specific customers • Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 19 LINK/ 10/100/ LINK RX 4xGB E Series ACTIVE 1000 LINK/ ACTIVE 10/100/ LINK RX 1000 LINK RX LINK RX GBE-1 LINE Aggregation GBE-2 SUB LINE/CASCA DE NET SCE platform device CMTS Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 20: Information About Management And Collection

    Chapter 1 General Overview Information About Management and Collection Information About Management and Collection The Cisco Service Control solution includes a complete management infrastructure that provides the following management components to manage all aspects of the solution: Network management •...
  • Page 21: Subscriber Management

    Data Collection The Cisco Service Control solution generates usage data and statistics from the SCE platform and forwards them as Raw Data Records (RDRs), using a simple TCP-based protocol (RDR-Protocol). The Cisco Service Control Management Suite (SCMS) Collection Manager (CM) software implements the collection system, listening in on RDRs from one or more SCE platforms and processing them on the local machine.
  • Page 22 Chapter 1 General Overview Data Collection Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 23: Chapter 2 Introduction To The Sce Platform

    C H A P T E R Introduction to the SCE Platform Revised: September 17, 2012, OL-26790-01 Introduction This chapter provides an introduction to the SCE 1000 2xGBE Platform, the Service Control hardware component. Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 24: Information About The Sce Platform

    Information About The SCE Platform Information About The SCE Platform The Service Control Engine (SCE) platform, which is the hardware component of the Cisco Service Control solution, is designed to support observation, analysis, and control of Internet/IP traffic. Table 2-1 summarizes model information for the SCE 1000 platform.
  • Page 25 • Unlit - Power supply B is either not present or has failed. • Status The Status LED indicates the operational status of the SCE 1000 system, as follows: • Unlit - indicates no power from either power unit. •...
  • Page 26: Back Panel

    LED Groups Description GBE ports The GBE LEDs indicate the operational status of the SCE 1000 line ports, as follows: • Link Green - indicates that the port link is up Unlit - indicates that the port link is down •...
  • Page 27: Information About Checking The Shipping Container Contents

    Information About Checking the Shipping Container Contents Use the SCE 1000 Component List to check the contents of the SCE 1000 platform shipping container. Do not discard the shipping container. You need the container if you move or ship the SCE 1000 platform in the future.
  • Page 28: Sce 1000 Installation Checklist

    1. Titles and quantities of documents will vary. You must order the type and quantity of documentation sets when you order the hardware. We no longer ship the entire SCE 1000 documentation set automatically with each system. You must Note specifically order the documentation as part of the sales order.
  • Page 29 GBE line ports operational Task Verified By Date Network interface cables and devices connected System power turned on System boot complete (SYSTEM-UP LED is on) Correct hardware configuration displayed after system banner appears Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 30 Chapter 2 Introduction to the SCE Platform SCE 1000 Installation Checklist Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 31 The Cisco SCE solution offers several basic topology options that permit the user to tailor the SCE Platform to fit the needs of a particular installation. An understanding of the various issues and options is crucial to designing, deploying, and configuring the topology that best meets the requirements of the individual system.
  • Page 32: Information About Topology Considerations

    Bypass mode when the SCE 1000 is not operational (on-failure)—This parameter determines • whether the system cuts the traffic or bypasses it when the SCE 1000 has failed. May be configured via either the setup command or the connection-mode command.
  • Page 33: Bypass Mechanism

    SW watchdog. A software mechanism that periodically checks for software failures in the – SCE 1000. If a failure is detected, an error massage is sent and the SCE 1000 reboots. Run time hardware tests. The system periodically tests the hardware components for error. If a •...
  • Page 34: Functionality

    Monitoring and Control—The SCE 1000 monitors and controls traffic flow. Decisions are enforced • by the SCE 1000 depending on the results of the monitoring functions of the SCE 1000 and the configuration of the Service Control Application for Broadband or Mobile solution.
  • Page 35: Information About Physical Installation

    • Bump-in-the-Wire (Inline) Topology Typically, the SCE 1000 is connected on a full duplex line between two devices (Router, BRAS, and so forth). When the SCE 1000 is installed as a bump-in-the-wire, it physically resides on the data link between the subscriber side and the network side, and can both receive and transmit traffic (Figure 3-1).
  • Page 36: External Splitting (Receive-Only) Topology

    3-2). In this topology, the traffic passes through the external splitter, which splits traffic to the SCE 1000. The external splitter is connected to the SCE 1000 via Rx links only. The SCE 1000, therefore, receives traffic only. It does not transmit.
  • Page 37: Information About Redundancy

    A single SCE 1000 platform does not provide redundancy for SCE 1000 control functions. In case of failure of the SCE 1000 unit, the SCE 1000 simply bypasses the traffic; the traffic link is not cut, but no control or monitoring functionality is available.
  • Page 38 After this occurs, the failed SCE 1000 can be fixed/replaced with no downtime, since the box is effectively disconnected from the network. After fixing/replacing the failed SCE 1000, you must copy the configuration of the current active SCE 1000 to the fixed/replaced SCE 1000.
  • Page 39: Information About Failure And Recovery

    Information About Failure and Recovery It is important to decide how the system should behave in case of the failure of the SCE 1000, both during the time that the unit is down and after recovery. This decision is influenced by several factors: Physical installation (connection mode) •...
  • Page 40: Information About Topology-Related Parameters

    The connection mode parameter refers directly to the physical topology in which the SCE 1000 is installed. Installation is possible in either of the two following modes: Inline — The SCE 1000 resides on the data link between the subscriber side and the network side, •...
  • Page 41: Link Failure Reflection Parameter

    Link Failure Reflection Parameter In a single SCE 1000 topology, the value of this parameter is determined by whether or not the link can be completely cut when the SCE 1000 fails, or whether traffic flow should continue across the link in spite of platform failure.
  • Page 42 2. In a redundant topology, it is also possible to configure admin status after abnormal boot to be Not operational. In this case, though, the SCE 1000 would have to be manually reloaded to resume full functionality. Cisco SCE 1000 2xGBE Installation and Configuration Guide...
  • Page 43: Introduction

    Revised: September 17, 2012, OL-26790-01 Introduction This chapter explains how to install a SCE 1000 platform in a rack or in a general tabletop or workbench installation. Additionally, this chapter contains instructions for installing or replacing the power supply units and fan modules.
  • Page 44: Information About Preparing To Install The Sce 1000 Platform

    The SCE 1000 chassis is fully assembled at the factory, including the application and software packages. No assembly is required. However, you need the following tools and equipment to install the SCE 1000 chassis and the rack-mount kit (if installing the SCE 1000 platform in a rack), fan modules, and power supplies: Number 1 and 2 Phillips screwdriver •...
  • Page 45: Information About Site Requirement Guidelines

    Figure 4-2 illustrates the airflow through the SCE 1000. Remember to leave a two inch (5 cm) clearance on both sides of the SCE 1000 and five inches (12.7 cm) Note at the rear for adequate airflow for the inlet and exhaust vents.
  • Page 46: Site Requirements

    For more complete information regarding safety and regulatory compliance, refer to the Regulatory Compliance and Safety Information for the Cisco Service Control Engines (SCE) document. The DC-powered SCE 1000 should be installed in a Restricted Access Location only. Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 47: Installing The Sce 1000 Platform

    This section provides instructions for the physical installation of the SCE 1000 platform, including how to install the SCE 1000 in a rack, how to install the SCE 1000 on a tabletop or workbench, and how to properly ground the SCE 1000 platform. The section contains the following topics: Installation Precautions, page 4-5 •...
  • Page 48: How To Install The Sce 1000 On A Workbench Or Tabletop

    How to Install the SCE 1000 on a Workbench or Tabletop You can install the SCE 1000 platform on any flat surface as long as the surface is large enough for the SCE 1000, and allows for adequate airflow/ventilation around the sides of the SCE 1000, as described in the Installation Precautions.
  • Page 49: Rack-Mounting A Sce 1000 Platform

    Mounting Brackets for 4-post Rack The SCE 1000 mounts to the two front rack posts with brackets that attach to the front of the SCE 1000 The inside width between the two posts or mounting strips (left and right) must be at least 17.3 inches (44 cm).
  • Page 50: How To Attach The Brackets To The Sce 1000

    Required, page 4-2 for a listing of the parts and tools required for installing the rack–mount. Align the rack-mount bracket to the side of the SCE 1000. Choose the proper bracket for your installation Step 1 (2-post rack or 4-post rack) as illustrated in Rack-Mounting a SCE 1000 Platform...
  • Page 51: How To Attach The Cross Rail Supports To The Rack

    This completes the steps for attaching the rack-mount brackets to the SCE 1000. If mounting the SCE 1000 in a rack with only two posts, skip to How to Mount the System to the Rack. If mounting the SCE 1000 in a rack with four posts, proceed to the next step to attach the cross rail supports to the rack.
  • Page 52: How To Mount The System To The Rack

    Step 1 engaged or that the rack is otherwise stabilized. Position the SCE 1000 so that the front end is closest to you, and lift it carefully to place it into the rack. Step 2 To prevent injury, avoid sudden twists or moves.
  • Page 53 SCE 1000) meet the mounting strips or posts on both sides of the rack (Figure 4-10). A rack with both front and back posts will have the cross rail supports installed. Slide the SCE 1000 onto these cross rails and push it all the way back. Figure 4-10...
  • Page 54 For each bracket, insert and tighten two appropriate screws to the rack. Step 5 Since the brackets support the weight of the entire SCE 1000 chassis, be sure to use all four screws to Note fasten the two rack-mount brackets to the rack posts.
  • Page 55: How To Attach A Chassis Ground Connection

    How to Attach a Chassis Ground Connection Before you connect the power or turn on the power to the SCE 1000 platform, it is required that you provide an adequate chassis ground (protective earth) connection for the SCE 1000 chassis. A grounding kit is provided with each SCE 1000.
  • Page 56 Chapter 4 Installation and Maintenance How to Attach a Chassis Ground Connection Figure 4-13 Grounding the Unit (DC) BY PA SS PO W ER PO W ER A Cisco SCE 1000 2xGBE Installation and Configuration Guide 4-14 OL-26790-01...
  • Page 57: Removing And Replacing A Power Supply Unit

    Each power supply has fans that cool the power supply unit. These fans also help to cool the internal components of the SCE 1000, as they direct the air flow to the outside through vents in the rear of the power supply unit.
  • Page 58: Leds

    IN LED Status for AC-input and DC-input Power Supply Units LED State Power Supply Unit Condition On (green) The input voltage is in the required range. The input voltage is not in the required range. Cisco SCE 1000 2xGBE Installation and Configuration Guide 4-16 OL-26790-01...
  • Page 59: Power Supply Specifications

    SNMP trap is sent in SNMP and the appropriate message is posted on the SCE 1000 CLI. Power Supply Specifications Table 4-7 lists the AC-input and DC-input power supply specifications for the SCE 1000 platform. Table 4-7 SCE 1000 Power Supply Specifications Input...
  • Page 60: Powering Down The Power Supply Unit And Disconnecting Input Power

    How to Power Down an AC-Input Power Supply To power down an AC-input power supply to the SCE 1000 platform, complete the following steps: Make sure that the power supply unit is switched off before replacing it (NO hot-swap). Note that one Note AC-input power supply can be running when the other power supply is being removed or replaced.
  • Page 61: What To Do Next

    Note that the power to the relevant power supply unit should be off, not necessarily all power to the Note SCE 1000 platform. One DC-input power supply can be running when the other power supply is being removed or replaced.
  • Page 62: How To Replace The Power Supply Unit

    Gently, but firmly, slide the module into the chassis until its faceplate is flush with the chassis rear panel. Step 3 When inserting a power supply into the SCE 1000 platform, do not use unnecessary force; slamming the Note power supply into the chassis can damage the connectors on the rear of the power supply.
  • Page 63: Reconnecting The Power

    BY PA SS PO W ER B PO W ER A For AC-input power, we recommend powering the SCE 1000 platform from a 120 VAC, 15A receptacle Note U.S. (240 VAC, 10A international) at the power source. 15 A branch circuit protection is recommended.
  • Page 64: How To Reconnect Dc-Input Power Supply Unit

    OFF position. Note that the power to the relevant power supply unit should be off, not necessarily all power to the SCE 1000 platform. One DC-input power supply can be running when the other power supply is being removed or replaced.
  • Page 65 If the new DC-input power supply unit is operating properly, these LEDs will be glowing green. Ensure that the power supply is properly aligned and the installation screw is tightened. Step 8 Cisco SCE 1000 2xGBE Installation and Configuration Guide 4-23 OL-26790-01...
  • Page 66: Fan Module Overview

    Note that a fan failure is often audible. Removing and Replacing the Fan Module The following sections explain how to remove and replace a fan module in a SCE 1000 platform: Do not remove or install modules without using appropriate anti-static guard measures. The SCE 1000 includes an anti-static wrist strap in the accessory kit.
  • Page 67: How To Replace The Fan Module

    When inserting a fan module into the SCE 1000 platform, do not use unnecessary force; slamming the fan module into the chassis can damage the connectors on the rear of the module. Seat the fan module in the SCE 1000 platform by tightening the two captive installation screws with a Step 4 1/4-inch flat-blade screwdriver.
  • Page 68: How To Replace The Battery

    How to Replace the Battery How to Replace the Battery The SCE 1000 has a lithium battery on its main circuit board. When the battery loses its charge, call Cisco Technical Support to replace the battery. Do not attempt to replace this battery yourself.
  • Page 69: Chapter 5 Connecting The Management Interfaces And Performing Initial System Configuration

    Revised: September 17, 2012, OL-26790-01 Introduction This chapter explains how to connect the SCE 1000 platform to a local console and perform the initial system configuration via the setup wizard that runs automatically. Additionally, this chapter contains instructions for cabling the Fast Ethernet Management interfaces.
  • Page 70: How To Set Up The Local Console

    How to Set Up the Local Console Even if you will be managing the SCE 1000 from a remote location, you must first connect the unit to a local console and configure the initial settings for the SCE 1000 to support remote management. When...
  • Page 71 Default settings are in square brackets ‘[]’. Would you like to continue with the System Configuration Dialog? [yes/no]: y Type y and press Enter. The system configuration dialog begins. Step 6 Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 72: Perform The Initial System Configuration

    For further information regarding any configuration step or specific parameter, refer to the relevant Note section in the Cisco SCE 2000 and SCE 1000 Software Configuration Guide. Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 73: Setup Command Parameters

    IP address of the SCE 1000. subnet mask Subnet mask of the SCE 1000. default gateway Default gateway. hostname Character string used to identify the SCE 1000. Maximum 20 characters. admin password Admin level password. Character string from 4-100 characters beginning with an alpha character.
  • Page 74 Name of the system administrator. Topology Configuration connection mode Is the SCE 1000 installed in inline topology or receive-only using an optical splitter? link bypass mode on operational status When the SCE 1000 is operational, should it bypass traffic or not?
  • Page 75: Example

    To abort the setup dialog at any point without making any configuration changes, press ^c . All changes already entered will be lost, with the exception of time settings. Step 1: Configuring Initial Settings Verify the following initial settings for the SCE 1000: IP address •...
  • Page 76: Example

    Enter IP address of default gateway [10.1.1.3]: Step 2: Configuring the Hostname The hostname is used to identify the SCE 1000. It appears as part of the CLI prompt and is also returned as the value of the MIB-II object sysName.
  • Page 77: Example

    Passwords are needed for all authorization levels in order to prevent unauthorized users from accessing Note the SCE 1000. Admin level should be used by the network administrator. Root level is for use by Cisco technician. Passwords must meet the following criteria: •...
  • Page 78: Step 4: Configuring Time Settings

    Are you sure? [yes/no]: y Enter new local time and date: 14:00:01 1 July 2002 Time zone was successfully set. The system clock and the calendar were successfully set. Cisco SCE 1000 2xGBE Installation and Configuration Guide 5-10 OL-26790-01...
  • Page 79: Example

    Enable SNTP broadcast client? [no]: y Enter time interval in seconds between unicast updates [900]: Would you like to configure SNTP unicast servers? [no]: y Enter IP address or hostname of SNTP unicast server: 10.1.1.1 Cisco SCE 1000 2xGBE Installation and Configuration Guide 5-11 OL-26790-01...
  • Page 80: Step 5: Configuring The Dns Settings

    Step 6 Exit the dialog. When IP addresses for all servers have been entered, exit the dialog by pressing press Enter. Would you like to add another Name Server? [no]: Cisco SCE 1000 2xGBE Installation and Configuration Guide 5-12 OL-26790-01...
  • Page 81: Example

    Would you like to add another Name Server? [no]: Step 6: Configuring the RDR Formatter Destination The SCE 1000 passes Raw Data Records (RDRs) to an external collection system via the RDR-Formatter. In order for the data to reach the correct location, the IP address of the external collection system and its port number must be configured.
  • Page 82: Information About Access Control Lists

    • Configuring ACLs The SCE 1000 can be configured with Access Control Lists (ACLs), which are used to permit or deny incoming connections on any of the management interfaces. ACL #0 is a pre-defined list that permits access to all IP addresses.
  • Page 83 If you entered a specific IP address, enter the wildcard bits to define a range of IP addresses and press Step 6 Enter. (See Entry Formats, page 5-14.) To define an individual IP address, type 0.0.0.0 and press Enter. There is no default for this parameter. Enter wildcard bits: Cisco SCE 1000 2xGBE Installation and Configuration Guide 5-15 OL-26790-01...
  • Page 84: Examples

    You are now prompted to assign the desired ACLs to restrict IP and Telnet access. • Restrict IP access to the SCE 1000 by assigning the appropriate ACL. Step 9 Type the number of the ACL to be assigned to IP access and press Enter.
  • Page 85: Step 8: Configuring Snmp

    Enter Telnet access-class [0]: 22 Step 8: Configuring SNMP Managing the SCE 1000 is possible also via a Network Management System (NMS) that supports SNMP. By default, SNMP is disabled on the SCE 1000. To enable SNMP management you must configure the following basic SNMP parameters: •...
  • Page 86 Configure the SNMP GET community. Step 3 Type the SNMP GET community name and press Enter. The SNMP agent that resides inside the SCE 1000 will respond only to GET requests that use this community string. Enter SNMP GET community name: Note that there is no default for this parameter.
  • Page 87 Enter up to 20 trap managers as described in step 7. When all entries have been added, accept the default: Would you like to add another SNMP trap manager? [no]: Press Enter to accept. Cisco SCE 1000 2xGBE Installation and Configuration Guide 5-19 OL-26790-01...
  • Page 88: Example

    About the Topology-Dependent Parameters The topology configuration menu is a series of guided questions relating to the deployment of the SCE 1000 in the network and its mode of operation. Values for the parameters are configured based on the user answers.
  • Page 89 Bypass state when the SCE 1000 is not operational (on-failure)—This parameter determines • whether the system cuts the traffic or bypasses it when the SCE 1000 has failed. Status after reboot caused by fatal error or abnormal shutdown—This parameter determines whether •...
  • Page 90: Examples

    • flow through the link. • After operation of the system resumes, and the SCE 1000 reboots, the SCE 1000 will resume operation. (Admin status after abnormal reboot is Operational.) • Would you like to enter the Topology configuration menu? [no]: y...
  • Page 91: Step 10: Completing And Saving The Configuration

    For a redundant topology, link bypass on-failure should be Cutoff, so that operation switches to the • backup link. After operation of the system resumes, and the reboots, the SCE 1000 will resume operation. • (Admin status after abnormal reboot is Operational.)
  • Page 92: Examples

    To save the configuration to a remote station, type y and press Enter. The system will ask for FTP path: Enter a full FTP path of the remote destination: This completes the procedures for initial configuration of the SCE 1000 platform. Step 6 The system informs you that the configuration is complete.
  • Page 93 Would you like to view the new configuration before it is applied? [yes/no]: Apply and Save this configuration? [yes/no]: n The changes you have just entered would be discarded, are you sure? [yes/no]:y Setup procedure aborted, no configuration changes made. Cisco SCE 1000 2xGBE Installation and Configuration Guide 5-25 OL-26790-01...
  • Page 94: Connecting The Management Interface

    IP address of the MNG port is always the same, regardless of which physical port is currently active. The procedures for cabling the management port and testing connectivity between the SCE 1000 and the remote management host are explained in the following sections: How to Cable the Management Port •...
  • Page 95: How To Verify Management Interface Connectivity

    You should hear an audible click indicating the latch has released. Carefully pull the plug out of the socket. If the management port Link LED on the SCE 1000 still does not light, verify that the cable is connected correctly to the appropriate network element on its second end.
  • Page 96 Chapter 5 Connecting the Management Interfaces and Performing Initial System Configuration How to Verify Management Interface Connectivity Cisco SCE 1000 2xGBE Installation and Configuration Guide 5-28 OL-26790-01...
  • Page 97: Chapter 6 Cabling The Line Ports And Completing The Installation

    This chapter provides instructions for cabling the Gigabit Ethernet ports and for configuring Gigabit Ethernet (GBE) interface parameters. When installing an External Optical Bypass module, the SCE 1000 line ports are connected to the Note module. See the External Optical Bypass Module for complete instructions.
  • Page 98: Connecting The Line Ports To The Network

    BRAS (in DSL access), a PDSN (in wireless access), a CMTS (in the Cable access), or a switch or router aggregator (in other topologies), and the network, where the SCE 1000 usually connects to a router or layer 3 switch network element. Figure 6-1...
  • Page 99: Single Link: Receive-Only Topology

    3 switch network element. This is the inline topology, providing both traffic monitoring and control capabilities. In this topology, all the traffic of the SCE 1000 is deployed as a transparent layer2 overlay on the customer’s existing network.
  • Page 100: How To Configure Gigabit Ethernet Auto-Negotiation

    When installing an External Optical Bypass module, the SCE 1000 line ports are connected to the Note module. See External Optical Bypass Module for complete instructions.
  • Page 101: Fiber Specifications

    The SCE 1000 may be ordered with either Multimode or Single Mode transceivers The transceiver type is indicated on the front panel under the ports. Note that both transceivers on any individual SCE 1000 are the same, either 850nm Multimode or 1310nm Single Mode.
  • Page 102: Testing Connectivity: Examining Link Leds And Counters

    Testing Connectivity: Examining Link LEDs and Counters If the SCE 1000 platform has been powered up, test now to verify that connectivity has been established on all links. If the SCE 1000 platform is not powered up, perform this step after starting the SCE 1000 platform.
  • Page 103: What To Do Next

    Out non unicast packets: 0 Out packets discarded: 0 What to Do Next You are now ready to continue to the next stage, How to Load and Activate a Service Control Application, page 6-8. Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 104: How To Load And Activate A Service Control Application

    How to Load and Activate a Service Control Application The SCE 1000 platform provides the basic functionality of Service Control analysis and enforcement. A Service Control solution requires that a Service Control application be loaded into the platform, to take advantage of the unique SCE platform capabilities.
  • Page 105: Introduction

    Basic SCE 1000 Platform Operations Revised: September 17, 2012, OL-26790-01 Introduction This chapter describes how to start up the SCE 1000 platform, reboot, and shutdown. It also describes how to manage configurations. Starting the SCE 1000 Platform, page 7-2 •...
  • Page 106: Starting The Sce 1000 Platform

    • Subsequent startups – Line and Cascade interfaces are properly cabled (optional) SCE 1000 platform is connected to at least one of the following types of management stations: – Direct connection to local console (CON port) – Remote management station via the LAN (Mng port) –...
  • Page 107: What To Do Next

    The Status LED should be a constant orange while booting. After a successful boot, the Status LED • is flashing green. It takes a several minutes for the SCE 1000 to boot and for the status LED to change from orange to Note flashing orange or flashing green.
  • Page 108: How To Verify Operational Status

    Final Tests How to Verify Operational Status After all the ports are connected, verify that the SCE 1000 is not in a Warning state. Step 1 On the SCE 1000 Front panel, examine that the Status LED is flashing green.
  • Page 109: Managing Sce 1000 Configurations

    Chapter 7 Basic SCE 1000 Platform Operations Managing SCE 1000 Configurations Managing SCE 1000 Configurations The procedures for managing SCE 1000 configurations are explained in the following sections: Viewing Configuration, page 7-5 • How to Save or Change the Configuration Settings, page 7-6 •...
  • Page 110: How To Save Or Change The Configuration Settings

    To remove a configuration command from the running-config, use the no form of the command. At the SCE 1000# prompt, type show running-config to view the running configuration. Step 1 The running configuration is displayed.
  • Page 111: Examples For Saving Or Changing The Configuration Settings

    Restoring a previous startup configuration means renaming the file so it overwrites the startup configuration (config.txt) file. Step 1 At the SCE 1000# prompt, type more tffs0:system/prevconf/config.txt to view the configuration file. The system displays the configuration information stored in the file. Step 2 Read the configuration information to make sure it is the configuration you want to restore.
  • Page 112: Example For Recovering A Previous Configuration

    LineCard 0 no silent no shutdown interface FastEthernet 0/0 ip address 10.1.5.109 255.255.0.0 interface FastEthernet 0/1 interface FastEthernet 0/2 exit line vty 0 4 exit SCE 1000#copy tffs0:system/prevconf/config.tx1 tffs0:system/config.txt SCE 1000# Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 113: How To Display The Sce Platform Version Information

    Use this command to display global static information on the SCE platform, such as software and hardware version, image build time, system uptime, last open packages names and information on the SLI application assigned. At the SCE 1000# prompt, type show version and press Enter. Step 1 Example for Displaying the SCE Platform Version Information The following example shows how to display the SCE platform version information.
  • Page 114: How To Display The Sce Platform Inventory

    How to Display the SCE Platform Inventory How to Display the SCE Platform Inventory Unique Device Identification (UDI) is a Cisco baseline feature that is supported by all Cisco platforms. This feature allows network administrators to remotely manage the assets in their network by tracing specific devices through either CLI or SNMP.
  • Page 115: Rebooting And Shutting Down The Sce Platform

    Examples for Rebooting the SCE Platform The following example shows the commands for system reboot. SCE 1000# reload Are you sure? y the system is about to reboot, this will end your CLI session How to Shut Down the SCE Platform Shutting down the SCE platform is required before turning the power off.
  • Page 116: Examples For Shutting Down The Sce Platform

    CLI console. This limitation helps prevent situations in which a user issues this command from a Telnet session, and then realizes he/she has no physical access to the SCE platform. Cisco SCE 1000 2xGBE Installation and Configuration Guide 7-12 OL-26790-01...
  • Page 117: Chapter 8 Troubleshooting

    The procedures in this chapter assume that you are troubleshooting the initial system startup, and that your SCE 1000 platform is in the original factory configuration. If you have removed or replaced components or changed any default settings, the recommendations in this chapter might not apply. Make...
  • Page 118: Troubleshooting Overview

    Troubleshooting Overview Troubleshooting Overview This section describes the troubleshooting methods used in this chapter and describes how the SCE 1000 platform is divided into subsystems for more efficient problem solving. If you are unable to easily solve the problem, contact a customer service representative for assistance and further instructions. Provide...
  • Page 119: Cli Commands For Troubleshooting

    SCE 2000 and SCE 1000 CLI Command Reference for more information. Remember that if the management interface is not operational, you should connect the SCE 1000 platform to a local console so that you can enter CLI commands for troubleshooting.
  • Page 120: Checking The Leds

    Checking the LEDs The front panel LEDS are the most immediate problem-detection mechanism of the platform. Refer to the following sections for information on SCE 1000 platform LEDS: Front Panel • SCE 1000 Operational Status •...
  • Page 121 SCE 1000 Operational Status Table 8-2 lists the operational states of the SCE 1000. The Status LED on the SCE 1000 Front Panel reflects the current SCE 1000 operational status. The operational status can be displayed using CLI command show system operation-status.
  • Page 122: Problem Solving Using A Subsystems Approach

    Startup problems are commonly due to the source power or to a poor cable connection. When you start up the SCE 1000 platform for the first time, you should observe the startup sequence described in Starting the SCE 1000 Platform. This section contains a more detailed description of the normal startup sequence and describes the steps to take if the system does not perform that sequence as expected.
  • Page 123: Troubleshooting The Power Subsystem

    Check the following to help isolate a problem in the power subsystem. In the normally configured SCE 1000 platform with redundant power supply units, it is unlikely that the device will not start at all. However, at startup it should be verified that both power supply units are operational, and therefore the following steps should be followed if one of the Power LEDs on the front panel remains unlit when the SCE 1000 platform is powered up.
  • Page 124: Troubleshooting The Firmware Package Installation

    In the output of the command, Package file platform mismatch. Verify that you have the package the package file platform is not file appropriate to your platform the correct installation file for type. the SCE 1000. Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 125: Troubleshooting The Management Subsystem

    When the management link is down and/or a Telnet connection cannot be established, you must open a CLI session on a local terminal connected to the CON port. This enables you to solve the problem and then reconnect through the management port. Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 126 • lit (link is up) CLI command: show Too many Telnet Close one or more of the telnet sessions connections (up to 5 open Telnet sessions. concurrent sessions are supported). Cisco SCE 1000 2xGBE Installation and Configuration Guide 8-10 OL-26790-01...
  • Page 127: Troubleshooting The Link Interface Subsystem

    GBE interface configuration. Note that in some cases, the problem which seems as a transmit problem could be in the Rx (no traffic is being received by the SCE 1000 or there is actually no traffic on the line, which could be a normal situation).
  • Page 128 Link is down. (LINK LED not lit and system status is WARNING) • Peer does not receive traffic from SCE 1000 (GBE link is lit and Tx LED is flashing) • GBE link is up but not receiving from peer (GBE link is lit, but Rx LED is not flashing) •...
  • Page 129 Check auto-negotiation disabled at the SCE configuration in the 1000 but enabled at SCE 1000 and in peer. peer. “How to View the Gigabit Ethernet Counters” section on page 6-7. Cisco SCE 1000 2xGBE Installation and Configuration Guide 8-13 OL-26790-01...
  • Page 130: Troubleshooting With The User Log

    You can view the log file by copying it to disk. This command copies both log files to the local SCE platform disk. From the SCE 1000# prompt, type logger get user-log file-name target-file name and press Enter. Step 1 The SCE 1000# prompt appears.
  • Page 131 • Step 1 From the SCE 1000# prompt, type show logger device user-file-log counters and press Enter. The logger lines information appears, followed by the SCE 1000# prompt. How to View the Non-volatile Logger Counters For Both the User Log File and the Debug Log File From the SCE 1000# prompt, type show logger nv-counters and press Enter.
  • Page 132: Generating A File For Technical Support

    From the SCE 1000# prompt, type logger get support-file filename and press Enter. Step 1 The support information file is created using the specified filename, and the SCE 1000# prompt appears. This operation may take some time. Cisco SCE 1000 2xGBE Installation and Configuration Guide...
  • Page 133: Appendix

    The SCE 1000 platform External Optical Bypass module preserves the service provider GBE links in case of complete power failure of the SCE 1000 platform, or for implementing a maintenance window. The SCE 1000 platform state-of-the-art Service Control platform is being deployed at ISPs, Cable and Wireless Tier1 provider networks, and is therefore required to comply with the carrier grade availability requirements of these mission critical networks.
  • Page 134: External Optical Bypass Functionality

    GBE signals to and from the SCE 1000 platform. In case the SCE 1000 platform stops providing power to the External Optical Bypass module, or in case the power cable is disconnected from the optical bypass module, the External Optical Bypass module becomes active, bypassing the two GBE links to the SCE 1000 platform, and thus preserving network connectivity.
  • Page 135: External Optical Bypass Module Front Panel

    NET Rx/Tx — GBE port that connects to the network element on the Network side of the link. • CONTROL — RJ-45 port that connects to the Bypass connector on the rear panel of the SCE 1000 • platform. The SCE 1000 platform controls the External Optical Bypass module via this connection, by the presence or absence of electrical power.
  • Page 136: Specifications

    How to Cable the External Optical Bypass Module, page A-5 • How to Install the Module in a Rack The following procedure describes how to install the module in a 19" rack. Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...
  • Page 137: How To Cable The External Optical Bypass Module

    Using the screws attached to the module, screw it into an empty position in the mounting panel. Step 1 Secure the module panel to the two front posts of the rack above the SCE 1000 platform. Leave at least Step 2 1.5 cm vertical clearance between the SCE 1000 platform and the module panel to provide space for the...
  • Page 138 Power up the SCE 1000 platform, as explained in Starting the SCE 1000 Platform. Step 5 Verify that the relevant GBE interfaces of the SCE 1000 platform are now in sync, as the External Optical Bypass module is now active (in bypass), and is performing a loopback on these interfaces.
  • Page 139 How to Cable the External Optical Bypass Module The SCE 1000 platform immediately starts providing power to the External Optical Bypass module, so the bypass module becomes inactive, and starts transferring the traffic to the SCE 1000 platform. The “No Bypass” LED should therefore be lit.
  • Page 140 Appendix A External Optical Bypass Module How to Cable the External Optical Bypass Module Cisco SCE 1000 2xGBE Installation and Configuration Guide OL-26790-01...

Table of Contents