Setup Print - MUTOH VJ-2638 Operation Manual

Before using
3.5.3

Setup print

Used to check the current setup of the printer.
NOTE
• Keep the printed setup print at hand.
TIP
Refer to the following for printing procedure.
3.5 Test print
The illustrations used in this section are print samples of VJ-1638X.
Ｓｅｔｕｐ Ｌｉｓｔ
＜Ｉｎｆｏｒｍａｔｉｏｎ＞
SerialNo. = XXXX000001
Model = VJ-1638X
Memory Size = 384MB
＜Ｍｅｎｕ Ｓｅｔｕｐ＞
[Number][Select]Menu
[ 1][*]User Type
[1]Print Mode
[2]Adjust Print
[3]PF Adjust
[1]Initial Adj.Print
[2]Initial Adjust
[3]Confirm Adj.Print
[4]Micro Adj. Print
[5]Micro Adjust
[4]PreHeater
[5]PlatenHeater
[6]Dryer
[7]Vacuum Fan
[ 2][*]Spitting
[ 3][*]Side Margin
[ 4][*]Media Initial
[ 5][*]Media Width
[ 6][*]Output Mode
[ 7][ ]Method of Cut
[ 8][*]Origin
[ 9][ ]Prevent Stick
[10][*]Standby Heating
[11][*]Head Travel
[12][*]Multi Strike
[13][*]Strike Wait
[14][*]Media Slant
108
VJ-2638/1638X/1938WX/1638WX OPERATION MANUAL
Firmware M = V 1.00
＝ Setup
＝ Type 1
＝ Quality 1(Effect ＝ Fine&Fog)
＝ 250.0/250mm
＝ 0.00%
＝ 30ﾟC
＝ 30ﾟC
＝ 30ﾟC
＝ High
＝ On(Pass Count = 1cnt)
＝ 5mm
＝ Width
＝ 1000mm
＝ Off(InkDryerTimer= 0sec)
＝ SingleCut-2steps
＝ Off
＝ 60min
＝ Data
＝ 1cnt
＝ 0.0sec
＝ On
!Error!
0：None［ ］ 2：None［ ］
1：None［ ］ 3：None［ ］
Head Height : Low
[Number][Select]Menu ＝ Setup
[15][*]Auto Cleaning
WaitingTime ＝ 360min
PrintingTime ＝ Off
Before Print ＝ Off
[16][*]Ink Status Smart/Chip KkCc ----/----/----
MmYy ----/----/----
[17][*]RollKind ＝ Off
[18][*]Exaust Fan ＝ Low
[19][*]Longstore
[20][*]CR Maintenance
[21][*]Initialization
[22][*]Life Times Head1 : E★★★★★F
Head2 : E★★★★★F
Pump1 : E★★★★★F
Pump2 : E★★★★★F
CR Motor : E★★★★★F
PF Motor : E★★★★★F
[22][*]IP Address ＝ 192.168.001.253
[23][*]Subnet Mask ＝ 255.255.255.000
[24][*]Gateway ＝ 192.168.001.254
SleepModeTimer ＝ 6h
Language = English
Temperature ＝ Celsius[ﾟC]
Length ＝ mm
2015/01/01 0:00
4：None［ ］
5：None［ ］
Cleaning Mode: Normal
3.5 Test print