HP 6600 Configuration Manual page 210
Hide thumbs
Also See for 6600:
- Security configuration manual (559 pages) ,
- Command reference manual (286 pages) ,
- Installation and getting started manual (103 pages)
Table of Contents
Advertisement
[RouterC] qos policy p1
[RouterC-policy-p1] classifier c1 behavior b1 mode dot1q-tag-manipulation
[RouterC-policy-p1] classifier c2 behavior b2 mode dot1q-tag-manipulation
[RouterC-policy-p1] classifier c3 behavior b3 mode dot1q-tag-manipulation
[RouterC-policy-p1] quit
[RouterC] qos policy p2
[RouterC-policy-p2] classifier c4 behavior b1 mode dot1q-tag-manipulation
[RouterC-policy-p2] classifier c5 behavior b2 mode dot1q-tag-manipulation
[RouterC-policy-p2] classifier c6 behavior b3 mode dot1q-tag-manipulation
[RouterC-policy-p2] quit
# Assign customer-side port GigabitEthernet 4/0/1 to CVLANs 101, 201, 301, 102, 202, 302,
and SVLANs 501 to 503. On this port, also enable customer-side QinQ, and apply uplink policy
p1 to incoming traffic.
[RouterC] interface GigabitEthernet 4/0/1
[RouterC-GigabitEthernet4/0/1] port link-type trunk
[RouterC-GigabitEthernet4/0/1] port trunk permit vlan 101 201 301 102 202 302 501 502
503
[RouterC-GigabitEthernet4/0/1] qinq enable downlink
[RouterC-GigabitEthernet4/0/1] qos apply policy p1 inbound
[RouterC-GigabitEthernet4/0/1] quit
# Assign customer-side port GigabitEthernet 4/0/2 to CVLANs 103, 203, 303, 104, 204, 304,
and SVLANs 501 to 503. On this port, also enable customer-side QinQ, and apply uplink policy
p2 to incoming traffic.
[RouterC] interface GigabitEthernet 4/0/2
[RouterC-GigabitEthernet4/0/2] port link-type trunk
[RouterC-GigabitEthernet4/0/2] port trunk permit vlan 103 203 303 104 204 304 501 502
503
[RouterC-GigabitEthernet4/0/2] qinq enable downlink
[RouterC-GigabitEthernet4/0/2] qos apply policy p2 inbound
[RouterC-GigabitEthernet4/0/2] quit
# Assign network-side GigabitEthernet 4/0/3 to SVLANs 501 to 503, set the port as a DHCP and
ARP trusted port, and enable network-side QinQ.
[RouterC] interface GigabitEthernet 4/0/3
[RouterC-GigabitEthernet4/0/3] port link-type trunk
[RouterC-GigabitEthernet4/0/3] port trunk permit vlan 501 502 503
[RouterC-GigabitEthernet4/0/3] dhcp-snooping trust
[RouterC-GigabitEthernet4/0/3] arp detection trust
[RouterC-GigabitEthernet4/0/3] qinq enable uplink
4.
Configure Router D:
# Assign port GigabitEthernet 4/0/1 to SVLANs 501 to 503.
<RouterD> system-view
[RouterD] interface GigabitEthernet 4/0/1
[RouterD-GigabitEthernet4/0/1] port link-type trunk
[RouterD-GigabitEthernet4/0/1] port trunk permit vlan 501 502 503
201
Advertisement
Table of Contents
