AudioCodes Mediant 1000 User Manual page 1010

Parameter
[RTPOnlyModeForTrunk_x]
Media IP Version
Preference
media-ip-ver-pref
[MediaIPVersionPreference]
SIT Q850 Cause
configure voip > sip-
definition settings > sit-
q850-cause
[SITQ850Cause]
SIT Q850 Cause For NC
configure voip > sip-
definition settings > release-
cause-for-sit-nc
[SITQ850CauseForNC]
SIT Q850 Cause For IC
configure voip > sip-
definition settings > q850-
cause-for-sit-ic
[SITQ850CauseForIC]
SIT Q850 Cause For VC
configure voip > sip-
definition settings > q850-
cause-for-sit-vc
[SITQ850CauseForVC]
SIT Q850 Cause For RO
configure voip > sip-
definition settings > q850-
cause-for-sit-ro
[SITQ850CauseForRO]
configure voip > gateway
manipulation settings >
User's Manual
RTPOnlyMode parameter value is ignored.
Enables the RTP Only feature per trunk. The x in the parameter name
denotes the trunk number, where 0 is Trunk 1. For a description of the
parameter, see the RTPOnlyMode parameter.
Note: For using the global parameter (i.e., setting the RTP Only
feature for all trunks), set the parameter to -1 (default).
Global parameter that defines the preferred RTP media IP addressing
version (IPv4 or IPv6) for outgoing SIP calls. You can also configure
this functionality per specific calls, using IP Profiles
(IpProfile_MediaIPVersionPreference). For a detailed description of the
parameter and for configuring this functionality in the IP Profiles table,
see Configuring IP Profiles on page 393.
Defines the Q.850 cause value specified in the SIP Reason header
that is included in a 4xx response when a Special Information Tone
(SIT) is detected on an IP-to-Tel call.
The valid range is 0 to 127. The default is 34.
Note: For mapping specific SIT tones, you can use the
SITQ850CauseForNC, SITQ850CauseForIC, SITQ850CauseForVC,
and SITQ850CauseForRO parameters.
Defines the Q.850 cause value specified in the SIP Reason header
that is included in a 4xx response when SIT-NC (No Circuit Found
Special Information Tone) is detected from the Tel side for IP-to-Tel
calls.
The valid range is 0 to 127. The default is 34.
Note: When not configured (i.e., default), the SITQ850Cause
parameter is used.
Defines the Q.850 cause value specified in the SIP Reason header
that is included in a 4xx response when SIT-IC (Operator Intercept
Special Information Tone) is detected from the Tel for IP-to-Tel calls.
The valid range is 0 to 127. The default is -1 (not configured).
Note: When not configured (i.e., default), the SITQ850Cause
parameter is used.
Defines the Q.850 cause value specified in the SIP Reason header
that is included in a 4xx response when SIT-VC (Vacant Circuit - non-
registered number Special Information Tone) is detected from the Tel
for IP-to-Tel calls.
The valid range is 0 to 127. The default is -1 (not configured).
Note: When not configured (i.e., default), the SITQ850Cause
parameter is used.
Defines the Q.850 cause value specified in the SIP Reason header
that is included in a 4xx response when SIT-RO (Reorder - System
Busy Special Information Tone) is detected from the Tel for IP-to-Tel
calls.
The valid range is 0 to 127. The default is -1 (not configured).
Note: When not configured (i.e., default), the SITQ850Cause
parameter is used.
Selects the Manipulation Set ID for manipulating all inbound INVITE
messages. The Manipulation Set is defined using the
1010
Mediant 1000B Gateway & E-SBC
Description
Document #: LTRT-27045