Oki B820N Setup Instructions page 90

Category
NETWORK SNMP
MENU
NETWORK
SCALE
HUB LINK
SETTING
FACTORY
DEFAULTS
MEMORY RECEIVE BUF
MENU SIZE
※7
2 2
RESOURCE
SAVE
SYS ADJUST X ADJUST
MENU
※8
Y ADJUST
SYS ADJUST DUPLEX X
MENU ADJUST
※8
Set [ADMIN MENU] - [OP MENU] - [MEMORY MENU] as
※7
Set [ADMIN MENU] - [OP MENU] - [MEMORY MENU] as
※8
90
User Menu
Item Value
ENABLE
DISABLE
NORMAL
SMALL
AUTO NEGOTIATE
100BASE-TX FULL
100BASE-TX HALF
10BASE-T FULL
10BASE-T HALF
EXECUTE
AUTO
0.5MB
1MB
2MB
4MB
8MB
16MB
32MB
AUTO
OFF
0.5MB
1MB
2MB
4MB
8MB
16MB
32MB
0.00MILLIMETER
+0.25MILLIMETER
+2.00MILLIMETER
-2.00MILLIMETER
-0.25MILLIMETER
0.00MILLIMETER
+0.25MILLIMETER
+2.00MILLIMETER
-2.00MILLIMETER
-0.25MILLIMETER
0.00MILLIMETER
+0.25MILLIMETER
+2.00MILLIMETER
-2.00MILLIMETER
-0.25MILLIMETER
Function / Notes
Sets SNMP of FTP.
"ENABLE" is selected in "TCP/IP" or "NETWARE".
NORMAL: When NORMAL is selected, it can work
effectively even when it is connected to HUB
that has a spanning tree feature. However,
printer start up time gets longer when
computers are connected with two or three
small LANs.
SMALL : When SMALL is selected, computers can cover
from two or three small LANs to a large LAN,
but it may not work effectively when it is
connected to HUB with a spanning tree feature.
Sets a method to link with HUB.
When Auto is set, a connection method to HUB is selected
automatically and attempts to connect.
Specifies whether to initialize the network menu or not.
Sets the size of receive buffer.
The maximum selection that Menu displays is equal to the
following formula or smaller.
Sets the size of resource saving area.
The maximum selection that Menu displays is equal to the
following formula or smaller.
Adjusts the position of a whole print image in the direction
that is perpendicular to the direction paper runs, that is
horizontally (at 0.25 mm pitch).
Any parts of the print image that go beyond the printable
area as a result of this designation are clipped.
When the PCL printer driver [Job Options] tab, the print
mode is set to PCL mode, this setting is valid.
Adjusts the position of a whole print image in the direction
paper runs, that is vertically (at 0.25mm pitch).
Any parts of the print image that go beyond the printable
area as a result of this designation are clipped.
When the PCL printer driver [Job Options] tab, the print
mode is set to picture mode, this setting is invalid.
Correction in negative values is invalid in PS Mode.
At the time of back page printing of Duplex, adjusts the
position of a whole print image in the direction paper
runs, that is vertically (at 0.25mm pitch).
Any parts of the print image that go beyond the printable
area as a result of this designation are clipped.
When the PCL printer driver [Job Options] tab, the print
mode is set to picture mode, this setting is invalid.
Duplex unit is installed.
" "
ENABLE , all items of setting under the MEMORY menu display.
" "
ENABLE , all items of setting under the MEMORY menu display.
B840dn B820n
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○