YASKAWA Z1000 Technical Manual page 462

Index
STo ............................................................................... 242
Stopping Method after Communication Error .............................. 167
Stopping Method Selection.................................................... 119
Storage Temperature .......................................................40, 304
Supported Properties of Objects .............................................. 367
Surrounding Area .................................................................40
Swing PWM ..................................................................... 140
T
T/L3.................................................................................62
T1-03 ............................................................................. 113
T1-04 ............................................................................. 113
T1-05 ............................................................................. 113
T1-06 ............................................................................. 113
T1-07 ....................................................................... 113, 114
TdE ............................................................................... 242
Terminal A1 Bias Setting...................................................... 161
Terminal A1 Function Selection.............................................. 161
Terminal A1 Gain Setting ..................................................... 161
Terminal A1 Signal Level Selection ......................................... 160
Terminal A2 Bias Setting...................................................... 162
Terminal A2 Function Selection.............................................. 162
Terminal A2 Gain Setting ..................................................... 162
Terminal A2 Signal Level Selection ......................................... 162
Terminal Block Configuration ..................................................60
Terminal Board Connection Error............................................ 229
Terminal TB1 .....................................................................36
Terminal TB2 .....................................................................36
Terminal TB3 ................................................................ 35, 36
Terminal TB4 .....................................................................35
Test Run.................................................................... 111, 114
Through Mode .................................................................. 157
TIM ............................................................................... 242
Time Data Error................................................................. 242
Time Not Set .................................................................... 242
Time to Continue Making Fault Restarts .................................... 329
Too Many Speed Search Restarts............................................. 242
Torque Compensation Gain ............................................. 140, 224
Torque Compensation Primary Delay Time ................................ 224
Torque Detection ............................................................... 164
Torque Detection 1 ............................................................. 157
Torque Detection Level 1................................................ 178, 330
Torque Detection Selection 1 ........................................... 177, 330
Torque Detection Time 1 ................................................ 178, 330
Troubleshooting without Fault Display...................................... 258
TrPC .............................................................................. 249
Tuning Errors.................................................................... 225
Types of Alarms, Faults, and Errors ......................................... 225
Types of Auto-Tuning for Induction Motors................................ 111
U
U/T1 ................................................................................62
U1-01 ............................................................................. 261
U1-07 ............................................................................. 259
U2-oo, U3-oo, and UB-oo Initialization ..................................... 184
UL3 ......................................................................... 242, 249
UL6 ......................................................................... 242, 249
UL and CSA Standards ........................................................ 443
UL Standards Compliance.......................................................62
Undertorque Detection 1................................................. 242, 249
462
Undertorque Detection 6....................................................... 249
Undertorque Detection Operation ............................................ 177
Undervoltage .................................................................... 250
Undervoltage 3 .................................................................. 243
Undervoltage 3 (Soft-Charge Circuit Fault)................................. 243
Undervoltage Detection Level (Uv1) .................................. 170, 328
Undervoltage Protection ....................................................... 304
Unexpected Noise from Connected Machinery............................. 262
Unit Code ........................................................................ 184
Up/Down Command Operation............................................... 152
Up Arrow Key.....................................................................92
User-Set Display Units Decimal Display.................................... 184
User-Set Display Units Maximum Value.................................... 184
User-Set Speed Agree 1........................................................ 155
User-Set Speed Agree 2........................................................ 157
Uv ................................................................................. 250
Uv1 ............................................................................... 243
Uv2 ............................................................................... 243
Uv3 ............................................................................... 243
V
V/f Characteristics .............................................................. 304
V/f Control.........................................................................27
V/f Control Mode Tuning ..................................................... 224
V/f Control Mode Tuning Parameters ....................................... 224
V/f Data Setting Error.......................................................... 252
V/f Gain During Speed Search................................................ 125
V/f Pattern Selection ..................................................... 145, 261
V/T2 ................................................................................62
Verifying Parameter Changes ................................................. 100
Vibration/Shock................................................................. 304
voF .......................................................................... 243, 250
Voltage drop calculation formula...............................................62
Voltage Reduction Rate.................................................. 186, 334
Voltage Restoration Complete Level .................................. 187, 334
Voltage Restoration Level ............................................... 186, 334
Voltage Restoration Sensitivity Time Constant ...................... 187, 334
Voltage Restoration Time Constant at Impact ........................ 187, 334
W
W/T3................................................................................62
Waiting for Run ................................................................. 250
Warranty Information ............................................................23
Watt Hour Pulse Output ....................................................... 160
Watt Loss 200 V Class Three Phase Models................................ 306
Watt Loss 400 V Class Three Phase Models................................ 306
Welded K3 Contactor Fault Select ........................................... 208
Wiring Distance................................................................. 141
Wiring the Control Circuit Terminal ...........................................80
Writing BACnet Bypass Parameters ......................................... 374
Writing to Multiple Registers ................................................. 391
WrUn ............................................................................. 250
Z
Z: Bypass Parameters .......................................................... 195
Z1000 Bypass Faults with Apogee Configuration ......................... 420
Zero Speed....................................................................... 154
YASKAWA ELECTRIC SIEP YAIZ1B 01E YASKAWA AC Drive – Z1000 Bypass Technical Manual