G.4: Type Codes For Output Devices - Honeywell nfs2-3030 Programming Manual

Type Codes for Output Devices
Type Code Point Type
PROCESS AUTO critical process
CO MONITOR CO alarm
* Local Mode treats this point as a fire alarm point.
† Does not participate in Local Mode
‡ Local Mode activation of NACs only. No releasing.
G.4 Type Codes for Output Devices
This section provides a list of Type Codes for SLC control module points. Select from these codes
to define the type of point.
Silenceable
Type Code (Y=yes
N=no)*
†
CONTROL Y
RELAY† Y
BELL CIRCUIT Y
STROBE CKT† Y
HORN CIRCUIT† Y
AUDIBLE CKT Y
SPEAKER Y
blank† Y
NONRESET N
CTL†
TELEPHONE N
CONTROL NAC Y
ISOLATED NAC Y
ISOLATED SPK Y
GEN ALARM† N
GEN SUPERVIS† N
GEN TROUBLE† N
GENERAL N
PEND†
TROUBLE N
PEND†
ALARMS PEND† N
‡
INST RELEASE N
NFS2-3030 Programming Manual — P/N 52545:K1 03/20/2012
Latching
Activates
(Y=yes
CBE
N=no)
N Y
Y Y
Table G.2 Type Codes for Monitor Modules (3 of 3)
Switch
Walk Test
Inhibit
(Y=yes, SLC Output Point
(Y=yes,
N=No)*
*
N=No)
N Y NAC
N Y Relay
N Y NAC
N Y NAC
N Y NAC
N Y NAC
N Y NAC
N Y NAC
N N Relay or NAC
N N Relay
N Y NAC
N Y NAC
N Y NAC
Y Y NAC
Y Y NAC
Y Y NAC
Y Y NAC
Y Y NAC
Y Y NAC
Y N NAC (SLC only)
Table G.3 SLC Control Module Type Codes (1 of 2)
Point Characteristics
Device Function
Monitors for a critical process
Monitors conventional CO detectors for a CO alarm condition.
Local Mode
Group Point
Types
n/a Supervised NAC
n/a Relay output
fire Supervised NAC
fire Supervised NAC
fire Supervised NAC
fire Supervised NAC
fire Supervised NAC for speaker circuits
n/a Supervised NAC for undefined device
n/a Supervised output, unaffected by "System Reset"
command
fire Supervised Telephone circuit
fire Supervised NAC
fire Supervised NAC for notification appliance, used
with audio isolators. Activates even if there is a short
on its NAC circuit. For ULC installations only.
fire Supervised NAC for speaker circuits, used with
audio isolators. Activates even if there is a short on
its audio circuit. For ULC installations only.
fire Control Module, XPC-8, or an XP5-C (in NAC mode)
configured as a Municipal Box Transmitter for NFPA
72 Auxiliary Fire Alarm Systems applications (MBT-
1 required). This Type ID can also be used for
general alarm activation.
supervisory Control Module, XPC-8, or an XP5-C (in NAC mode)
activated under any Supervisory condition (includes
sprinkler type).
trouble Control Module, XPC-8, or an XP5-C (in NAC mode)
activated under any System Trouble condition.This
device will not turn ON when it is in trouble (short or
open).
trouble Control Module XPC-8 circuit, or an XP5-C (in NAC
mode) that will activate upon receipt of an alarm
and/or trouble condition, and remain in the ON state
until all events have been ACKNOWLEDGED. This
device will not turn ON when it is in trouble (short or
open)
trouble Control Module or an XP5-C (in NAC mode) that will
activate upon receipt of a trouble condition, and
remain in the ON state until all troubles have been
ACKNOWLEDGED. This device will not turn ON
when it is in trouble (short or open).
fire Control module or NAC for output that will activate
upon receipt of an alarm condition, and remain in
the alarm state until all alarms have been
acknowledged.
fire Supervised for open circuits and ground faults.
Short = normal
Type Codes
Device Function
141