Yamaha CL1 Reference Manual page 40

3.
Press a knob in the SELECTED CHANNEL section to access the SELECTED CHANNEL
VIEW screen.
4.
In the TO MIX/MATRIX field on screen, make sure that the MIX1–16 button or
MIX17–24/MATRIX button is turned on.
The TO MIX/TO MATRIX field displays the corresponding knobs and buttons. If this button is
off, press the button to turn it on.
MIX buses can be either a FIXED type that features a fixed send level, or a VARI type that features
a variable send level. The MATRIX buses are all VARI type. You can switch between FIXED and
VARI types for each two adjacent odd/even-numbered MIX buses. To do so, press the SETUP
button, the USER SETUP button, and then the BUS SETUP button to open the BUS SETUP
popup window.
If the send-destination MIX bus is a FIXED type, a circle ( ) is displayed instead of the TO MIX
SEND LEVEL knob. In this case, you cannot adjust the send level.
If the send-destination MIX bus is a VARI type, or if the send-destination is a MATRIX bus, the
TO MIX SEND LEVEL knob will be displayed in the same color as the corresponding knob in the
SELECTED CHANNEL section. In this case, you can use the corresponding knob in the
SELECTED CHANNEL section to adjust the send level.
If necessary, you can specify two adjacent odd/even-numbered MIX/MATRIX buses as a stereo
bus and link the main parameters.
If the send-destination MIX/MATRIX bus is assigned as stereo, the left knob of the two adjacent
TO MIX/MATRIX SEND LEVEL knobs will operate as the TO MIX/MATRIX PAN knob. (If
BALANCE mode is selected in the TO STEREO/MONO popup window, it will operate as a
BALANCE knob).
For a MONO channel, the right knob will adjust the common send level to the two MIX/MATRIX
buses, and the left knob will adjust the panning between the two MIX/MATRIX buses. Rotating
the left TO MIX/MATRIX SEND PAN knob counter-clockwise will increase the amount of signal
sent to the odd-numbered MIX/MATRIX bus, and rotating it clockwise will increase the amount
sent to the even-numbered MIX/MATRIX bus.
For a STEREO channel, if BALANCE mode has been selected on the TO STEREO/MONO popup
window (8ch), the right knob adjusts the common send level for the two MIX/MATRIX buses,
and the left knob adjusts the volume balance of the left and right signals sent to the two MIX/
MATRIX buses. Rotating the left TO MIX/MATRIX SEND BAL knob counter-clockwise will
increase the amount of signal sent from the L-channel to the odd-numbered MIX/MATRIX bus,
and rotating it clockwise will increase the amount sent from the R-channel to the even-numbered
MIX/MATRIX bus. If PAN mode has been selected in the TO STEREO/MONO popup window
(8ch), the left knob will function as the PAN knob. The right knob will function as send level, just
as in BALANCE mode.
5.
Make sure that the TO MIX/MATRIX SEND ON/OFF button is turned on for the
send-destination MIX bus.
If this button is off, press the button on screen to turn it on.
6.
In the SELECTED CHANNEL section, use the MIX/MATRIX SEND LEVEL knobs to
adjust the send levels to the MIX/MATRIX buses.
NOTE
If you want to monitor the signal being sent to a specific MIX/MATRIX bus, use the Bank Select
keys in the Centralogic section to access the corresponding MIX/MATRIX channel, and then
press the appropriate [CUE] key in the Centralogic section.
7.
You can use the [SEL] keys on the top panel to switch input channels and control
the send level to all MIX/MATRIX buses in the same way.
40
Input channels
Reference Manual