Yamaha CL1 Reference Manual page 236

Hide thumbs Also See for CL1:
Table of Contents

Advertisement

■ FLANGE
Two input, two output flange effect.
Parameter
Range
FREQ.
0.05–40.00 Hz
Modulation speed
DEPTH
0–100%
Modulation depth
MOD. DLY
0.0–500.0 ms
Modulation delay time
Feedback gain (plus values for normal-phase feedback, minus values for
FB. GAIN
–99 to +99%
reverse-phase feedback)
WAVE
Sine, Tri
Modulation waveform
SYNC
OFF/ON
Tempo parameter sync on/off
*1
NOTE
Used in conjunction with TEMPO to determine FREQ.
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
EQ F
100 Hz–8.00 kHz
EQ (peaking type) frequency
EQ G
–12.0 to +12.0 dB
EQ (peaking type) gain
EQ Q
10.0–0.10
EQ (peaking type) bandwidth
HSH F
50.0 Hz–16.0 kHz
High shelving filter frequency
HSH G
–12.0 to +12.0 dB
High shelving filter gain
*1.
■ SYMPHONIC
Two input, two output symphonic effect.
Parameter
Range
FREQ.
0.05–40.00 Hz
Modulation speed
DEPTH
0–100%
Modulation depth
MOD. DLY
0.0–500.0 ms
Modulation delay time
WAVE
Sine, Tri
Modulation waveform
SYNC
OFF/ON
Tempo parameter sync on/off
*1
NOTE
Used in conjunction with TEMPO to determine FREQ.
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
EQ F
100 Hz–8.00 kHz
EQ (peaking type) frequency
EQ G
–12.0 to +12.0 dB
EQ (peaking type) gain
EQ Q
10.0–0.10
EQ (peaking type) bandwidth
HSH F
50.0 Hz–16.0 kHz
High shelving filter frequency
HSH G
–12.0 to +12.0 dB
High shelving filter gain
*1.
Description
Description
236
■ PHASER
Two input, two output 16-stage phaser.
Parameter
Range
FREQ.
0.05–40.00 Hz
Modulation speed
DEPTH
0–100%
Modulation depth
Feedback gain (plus values for normal-phase feedback, minus values for
FB. GAIN
–99 to +99%
reverse-phase feedback)
OFFSET
0–100
Lowest phase-shifted frequency offset
PHASE
0.00–354.38 degrees
Left and right modulation phase balance
STAGE
2, 4, 6, 8, 10, 12, 14, 16
Number of phase shift stages
SYNC
OFF/ON
Tempo parameter sync on/off
*1
NOTE
Used in conjunction with TEMPO to determine FREQ.
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
HSH F
50.0 Hz–16.0 kHz
High shelving filter frequency
HSH G
–12.0 to +12.0 dB
High shelving filter gain
*1.
■ DYNA.FLANGE
Two input, two output dynamically controlled flanger.
Parameter
Range
SOURCE
INPUT, MIDI
Control source: input signal or MIDI Note On velocity
SENSE
0–100
Sensitivity
DIR.
UP, DOWN
Upward or downward frequency change
*1
DECAY
Decay speed
OFFSET
0–100
Delay time offset
Feedback gain (plus values for normal-phase feedback, minus values for
FB.GAIN
–99 to +99%
reverse-phase feedback)
LSH F
21.2 Hz–8.00 kHz
Low shelving filter frequency
LSH G
–12.0 to +12.0 dB
Low shelving filter gain
EQ F
100 Hz–8.00 kHz
EQ (peaking type) frequency
EQ G
–12.0 to +12.0 dB
EQ (peaking type) gain
EQ Q
10.0–0.10
EQ (peaking type) bandwidth
HSH F
50.0 Hz–16.0 kHz
High shelving filter frequency
HSH G
–12.0 to +12.0 dB
High shelving filter gain
*1. 6.0 ms–46.0 s (fs=44.1 kHz), 5.0 ms–42.3 s (fs=48 kHz)
Appendices
Description
Description
Reference Manual

Advertisement

Table of Contents
loading

This manual is also suitable for:

Cl3Cl5

Table of Contents