Yamaha CL1 Reference Manual page 237

■ DYNA.PHASER
Two input, two output dynamically controlled phaser.
Parameter Range
SOURCE INPUT, MIDI Control source: input signal or MIDI Note On velocity
SENSE 0–100 Sensitivity
DIR. UP, DOWN Upward or downward frequency change
*1
DECAY Decay speed
OFFSET 0–100 Lowest phase-shifted frequency offset
Feedback gain (plus values for normal-phase feedback, minus values for
FB.GAIN –99 to +99%
reverse-phase feedback)
STAGE 2, 4, 6, 8, 10, 12, 14, 16 Number of phase shift stages
LSH F 21.2 Hz–8.00 kHz Low shelving filter frequency
LSH G –12.0 to +12.0 dB Low shelving filter gain
HSH F 50.0 Hz–16.0 kHz High shelving filter frequency
HSH G –12.0 to +12.0 dB High shelving filter gain
*1. 6.0 ms–46.0 s (fs=44.1 kHz), 5.0 ms–42.3 s (fs=48 kHz)
■ HQ. PITCH
One input, two output high-quality pitch shifter.
Parameter Range
PITCH –12 to +12 semitones Pitch shift
FINE –50 to +50 cents Pitch shift fine
DELAY 0.0–1000.0 ms Delay time
Feedback gain (plus values for normal-phase feedback, minus values for
FB. GAIN –99 to +99%
reverse-phase feedback)
MODE 1–10 Pitch shift precision
SYNC OFF/ON Tempo parameter sync on/off
*1 Used in conjunction with TEMPO to determine DELAY
NOTE
*1.
Description
Description
(Maximum value depends on the tempo setting)
237
■ DUAL PITCH
Two input, two output pitch shifter.
Parameter Range
PITCH 1 –24 to +24 semitones Channel #1 pitch shift
FINE 1 –50 to +50 cents Channel #1 pitch shift fine
Channel #1 level (plus values for normal phase, minus values for reverse
LEVEL 1 –100 to +100%
phase)
PAN 1 L63 to R63 Channel #1 pan
DELAY 1 0.0–1000.0 ms Channel #1 delay time
Channel #1 feedback gain (plus values for normal-phase feedback, minus
FB. G 1 –99 to +99%
values for reverse-phase feedback)
MODE 1–10 Pitch shift precision
PITCH 2 –24 to +24 semitones Channel #2 pitch shift
FINE 2 –50 to +50 cents Channel #2 pitch shift fine
Channel #2 level (plus values for normal phase, minus values for reverse
LEVEL 2 –100 to +100%
phase)
PAN 2 L63 to R63 Channel #2 pan
DELAY 2 0.0–1000.0 ms Channel #2 delay time
Channel #2 feedback gain (plus values for normal-phase feedback, minus
FB. G 2 –99 to +99%
values for reverse-phase feedback)
SYNC OFF/ON Tempo parameter sync on/off
*1
NOTE 1 Used in conjunction with TEMPO to determine Channel #1 delay
NOTE 2 *1 Used in conjunction with TEMPO to determine Channel #2 delay
*1.
■ TREMOLO
Two input, two output tremolo effect.
Parameter Range
FREQ. 0.05–40.00 Hz Modulation speed
DEPTH 0–100% Modulation depth
WAVE Sine, Tri, Square Modulation waveform
SYNC OFF/ON Tempo parameter sync on/off
*1
NOTE Used in conjunction with TEMPO to determine FREQ.
LSH F 21.2 Hz–8.00 kHz Low shelving filter frequency
LSH G –12.0 to +12.0 dB Low shelving filter gain
EQ F 100 Hz–8.00 kHz EQ (peaking type) frequency
EQ G –12.0 to +12.0 dB EQ (peaking type) gain
EQ Q 10.0–0.10 EQ (peaking type) bandwidth
HSH F 50.0 Hz–16.0 kHz High shelving filter frequency
HSH G –12.0 to +12.0 dB High shelving filter gain
*1.
Appendices
Description
(Maximum value depends on the tempo setting)
Description
Reference Manual