D-Link xStack DGS-3620 Series Reference Manual page 628

®
xStack DGS-3620 Series Layer 3 Managed Stackable Gigabit Switch Web UI Reference Guide
BGP bgpEstablishedNotification
bgpBackwardTransNotification
Stacking swUnitInsert
swUnitRemove
swUnitFailure
swUnitTPChange
swUnitRoleChange
VRRP vrrpTrapNewMaster
vrrpTrapAuthFailure
Port Security
swL2PortSecurityViolationTrap
Safe Guard
swSafeGuardChgToNormal
swSafeGuardChgToExhausted
LBD swPortLoopOccurred
swPortLoopRestart
(2) macaddr
(3) portNumber
(4) agentGratuitousARPInterfaceName
The BGP established event is generated when
the BGP FSM enters the ESTABLISHED state.
Binding objects:
(1) bgpPeerRemoteAddr
(2) bgpPeerLastError
(3) bgpPeerState
The bgpBackwardTransNotification event is
generated when the BGP FSM moves from a
higher numbered state to a lower numbered
state.
Binding objects:
(1) bgpPeerRemoteAddr
(2) bgpPeerLastError
(3) bgpPeerState
Unit Hot Insert notification.
Binding objects:
(1) swUnitMgmtId.
(2) swUnitMgmtMacAddr.
Unit Hot Remove notification.
Binding objects:
(1) swUnitMgmtId.
(2) swUnitMgmtMacAddr.
Unit Failure notification.
Binding objects:
(1) swUnitMgmtId.
The stacking topology change notification.
Binding objects:
(1) swStackTopologyType
(2) swUnitMgmtId
(3) swUnitMgmtMacAddr
The stacking unit role change notification.
Binding objects:
(1) swStackRoleType
(2) swUnitMgmtId
The newMaster trap indicates that the sending
agent has transitioned to 'Master' state.
Binding objects:
(1) vrrpOperMasterIpAddr
A vrrpAuthFailure trap signifies that a packet
has been received from a router whose
authentication key or authentication type
conflicts with this router's authentication key or
authentication type. Implementation of this trap
is optional.
Binding objects:
(1) vrrpTrapPacketSrc
(2) vrrpTrapAuthErrorType
When the port security trap is enabled, new
MAC addresses that violate the pre-defined port
security configuration will trigger trap messages
to be sent out.
Binding objects:
(1)swPortSecPortIndex
(2)swL2PortSecurityViolationMac
This trap indicates system change operation
mode from axhausted to normal.
Binding objects:
(1) swSafeGuardCurrentStatus
This trap indicates System change operation
mode from normal to exhausted.
Binding objects:
(1) swSafeGuardCurrentStatus
The trap is sent when a port loop occurs.
Binding objects:
(1) swLoopDetectPortIndex
The trap is sent when a port loop restarts after
the interval time.
Binding objects:
627
1.3.6.1.2.1.15.0.1
1.3.6.1.2.1.15.0.2
1.3.6.1.4.1.171.12.11.2.2.1
.0.1
1.3.6.1.4.1.171.12.11.2.2.1
.0.2
1.3.6.1.4.1.171.12.11.2.2.1
.0.3
1.3.6.1.4.1.171.12.11.2.2.1
.0.4
1.3.6.1.4.1.171.12.11.2.2.1
.0.5
1.3.6.1.2.1.68.0.1
1.3.6.1.2.1.68.0.2
1.3.6.1.4.1.171.11.118.X.2.
100.1.2.0.2,(X:module ID)
1.3.6.1.4.1.171.12.19.4.1.0
.2
1.3.6.1.4.1.171.12.19.4.1.0
.1
1.3.6.1.4.1.171.12.41.10.0.
1
1.3.6.1.4.1.171.12.41.10.0.
2