Page 1
Mirage 4K35 U s e r M a n u a l 020-101377-03...
Page 3
Mirage 4K35 U s e r M a n u a l 020-101377-03...
Page 4
The warranty does not apply to any product where the serial number has been removed or obliterated. The warranty also does not apply to any product sold by a reseller to an end user outside of the country where the reseller is located unless (i) Christie has an office in the country where the end user is located or (ii) the required international warranty fee has been paid.
Page 5
CAN ICES-3 (A) / NMB-3 (A) 이 기기는 업무용 (A 급 ) 으로 전자파적합등록을 한 기기이오니 판매자 또는 사용자는 이점을 주의하시기 바라며 , 가정 외의 지역에서 사용하는 것을 목적으로 합니다 . Environmental The product is designed and manufactured with high-quality materials and components that can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from regular waste.
Page 6
Addendum Translated copies of this document are provided on the CD in the back of this document. The CD may also contain additional product documentation. Read all instructions before using or servicing this product. 本文档 的翻译副本在本文档背面 的 C D 上 提供 。该 CD 中 还可 能包 含其 他产品 文 档。使...
Active stereo 3D configuration ........37 Mirage 4K35 User Manual...
Page 9
Projector LED status indicators ........56 Mirage 4K35 User Manual...
Page 10
Inspect and fill the coolant reservoir ....... . 72 Mirage 4K35 User Manual...
Page 11
........84 Frame multiplication applied to incoming video signals when not required ..84 Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Page 12
Accessories ........... 99 Mirage 4K35 User Manual...
Safety and warning guidelines This projector must be operated in an environment that meets the operating range specification. Use only the attachments and/or accessories recommended by Christie. Use of others may result in the risk of fire, shock, or personal injury.
• Verify that the projector is using a line cord, socket, and power plug that meets the appropriate local rating standards. Use only an AC power cord recommended by Christie. Do not attempt operation if the AC supply and cord are not within the specified voltage and power range.
This equipment is included in included in the Christie Protective Clothing Safety kit P/N: 598900-095. Christie’s protective clothing recommendations are subject to change. Any local or federal specifications take precedence over Christie recommendations. Mirage 4K35 User Manual...
Indicates exposure to bright light. To avoid personal injury, never look directly at the light source. Indicates the presence of an explosion hazard. To avoid personal injury, always disconnect all power sources and wear Christie approved protective clothing. Mirage 4K35 User Manual...
Page 17
This label warns of a cross-connection hazard when installing multiple projectors at once. A fire hazard exists if a lamp power supply interlock cable is connected to a different projector than its lamp power cables. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
120 frames per second. Contact your dealer If you encounter a problem with your Christie projector, contact your dealer. To assist with the servicing of your projector, enter the information in the tables below and keep this information with your records.
129-003104-XX How the projector works The Mirage 4K35 accepts a variety of input signals for projection on front or rear projection screens, typical in commercial or other large screen applications. High-brightness light is generated by a short arc Xenon lamp, then modulated by three Digital Micromirror Device (DMD) panels responding to incoming data streams of digitized red, green and blue color information.
Page 20
Shroud • Access keys • Web registration form Verify the following components were received with the Lamp Power Supply (P/N: 129-003104-XX): • 10’ line cord (250V/10A) • Harness package (includes four cables) Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Three-phase, 38A 200-230VAC + Earth (North America and Japan) Three-phase, 26A 380-415VAC + Neutral + Earth (regions outside North America and Japan) • This product can be connected to an IT power distribution system. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
12” screwdrivers: Phillips #2 (magnetic) and flat • 19 mm and 7/8” wrenches • Assorted Allen keys (metric) • Christie approved protective safety clothing if working with the lamp • Lens cleaning tissue and solution Projector components LAMP SIDE LENS SIDE...
75. Shroud (two-piece) Covers the motorized lens mount assembly. Projection lens A variety of lenses can be used with the Mirage 4K35. For a list of available lenses, see Accessories on page 99 Air filter cover and air filter Filters the intake air before it circulates through the front compartment to cool the main electronics.
3. If using an optional rack stand (P/N: 108-282101-02), assemble the rack stand using the instructions provided with the rack stand. Use the hold down clamp (P/N: 116-100101-01) when securing the projector to the rack stand. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Do not install any components in front of the lamp power supply that will restrict airflow. 8. Insert airflow duct into rack stand from the outside. 9. Secure airflow duct to rack stand using screws from the rack stand panels. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Never compromise safety by returning the current through the ground. Connect ground first to reduce shock hazard. • Use an appropriate strain relief connector on the AC supply cable to prevent the cable from rubbing against the LPS knockout plate and becoming damaged. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Page 27
Pull the spring plunger to open the igniter door. The door can also be lifted off the hinges to remove it completely. f. Route the positive (+) and negative (-) leads from the LPS through the two strain reliefs in the projector baseplate. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Page 28
Internal input line voltage switch setting must match AC available on site. 6. Connect one end of the line cord into the LPS power connector labeled Projector ONLY. If using the longer DC cable kits, the projector head must be powered separately using Christie recommended line cord provided for your region.
Installation and Setup 8. If using a Christie extractor, connect the line cord to the LPS connector labeled Extractor ONLY. 9. Verify the LPS to projector connections by making sure that all cables connected to the LPS are connected to the same projector.
3. Insert the convenience outlet harness (black) wire into the second position on the terminal block. 4. Tighten the screw to secure the harness in place. Ensure the wire insulation is not crimped under the screw. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
1. Secure a safety lifting strap rated to handle the projector weight at the rear of the projector. 2. Hoist up the projector. 3. To adjust the vertical or horizontal position of the projector, extend or retract the adjustable feet on the bottom of the projector (A). Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
2. Tighten the mounting arm lock until it fits tightly on the joint. The TPC safety strap comes installed on the projector ball point. 3. Connect the cable from the touch panel controller (TPC) to the connector on the rear panel of the projector. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
4.5 kW 600 CFM 6.0 kW 600 CFM *600 CFM is required in projection rooms with ambient temperature above 25°C (77°F) or elevation (above sea level) greater than 3000 feet (914.4 m). Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
To prevent the projector from overheating or becoming unsafe, an alarm sounds if the duct is obstructed or a fan fails. Christie recommends regularly verifying that the exhaust is unobstructed and functioning correctly.
79. Portrait mode 1. Orient the projector in the frame with the lamp door facing downward (as shown). The maximum tilt angle is ±15 degrees. 2. Set up the customer-supplied mounting frame. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
3D source material. Hardware requirements Note the following hardware requirements for stereo 3D applications: • Christie Digital Systems Mirage 4K Series projector • 3D stereo sync cable for Direct-Input 3D (and frame doubled) • A source, usually a computer with a 3D graphics card(s) Mirage 4K35 User Manual 020-101377-03 Rev.
In response to the 3D Sync Out signal from the projector, the IR emitter emits an infrared signal to a receiver in the active 3D shutter glasses. This synchronizes the active glasses to alternatively open and close for the active stereo 3D applications. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
“ghosting” of the video content (known as cross-talk in stereo 3D applications) or other more subtle color artifacts. Visual performance can be optimized by adjusting the Dark Interval and the 3D Sync Delay settings. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
This adjusts the timing of the sync pulse in relation to the dark time transition on the DMDs. Use the default value of 0 as a starting point. Configure the projector for the 3D source 1. Select the channel (from the Home tab) best suited for the 3D source. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Page 40
2. To select the correct EDID timing, tap Main > Configuration > EDID Timing Select and select the required EDID timing. 3. Connect all the required cables between the 3D source and the projector. 4. Configure your 3D source. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
The following table shows the video quadrant mappings for the 3GIC, TDPIC, and THIC Four-Port input configurations: input Quadrants Columns Four-Port configuration—Two cards (1) Slot 1 1-In Top left 1 (left most) Slot 1 2-In Bottom left Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
The following table shows the video quadrant mappings for the DDIC Two-Port input configuration: input Columns Two-Port Configuration—Two cards (1) Slot 1 1-Dual Link DVI-I 1 (left most) Slot 2 1-Dual Link DVI-I Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Connect a video source using 3G input card The 3G input card (3GIC) accepts digital video data from HD and 3G-SDI (Serial Digital Interface) sources. The input configurations listed below are supported. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
One THIC card card (in any slot). In this configuration, the HDMI input supplies the entire video raster. One-Port, Dual- May be used for Dual-Input 3D configurations. One THIC card Input 3D Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
DDIC input configuration, see Two-Port: TDPIC card on page Select a video source After connecting a video source to the projector, you must select it using the touch panel controller (TPC). Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Notice. Failure to comply with the following may result in property damage. The RS232 port located on the MCPU faceplate uses Christie-proprietary protocol and is intended for Christie accessories or automation controllers only. For more information on the serial commands,...
• To obtain information automatically from the network, tap Automatic. • To manually enter the network information, tap Manual and enter the IP Address, Subnet Mask and Gateway (optional). 3. Click Ok. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
4. With the test pattern on screen, re-check the projector leveling so the top edge of the image is parallel to the top edge of the screen. For more details, see Position the projector on page 24 and Work with lenses on page 60. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Warning! Failure to comply with the following could result in death or serious injury. When doing optical adjustments on an operating projector and the top lid is removed, everyone within the immediate vicinity must wear safety glasses with side shields and Christie approved protective safety clothing (P/N: 598900-95).
Warning! Failure to comply with the following could result in death or serious injury. When doing optical adjustments on an operating projector and the top lid is removed, everyone within the immediate vicinity must wear safety glasses with side shields and Christie approved protective safety clothing (P/N: 598900-95).
Page 51
10. Tighten the lock screw (A) and the lens mount stabilization screw (D) to maintain the adjustments. 11. Check the boresight again. 12. Perform a lens calibration. For more details, see Calibrate the lens motors on page 79. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Warning! Failure to comply with the following could result in death or serious injury. When doing optical adjustments on an operating projector and the top lid is removed, everyone within the immediate vicinity must wear safety glasses with side shields and Christie approved protective safety clothing (P/N: 598900-95).
Contact your Christie accredited service technician to correct DMD convergence issues. Color correction The Mirage 4K35 provides predefined and custom color adjustments using the Color Correction menu. The available color adjustment controls are listed in the table below: Menu...
Warning! Failure to comply with the following could result in death or serious injury. When doing optical adjustments on an operating projector and the top lid is removed, everyone within the immediate vicinity must wear safety glasses with side shields and Christie approved protective safety clothing (P/N: 598900-95).
Page 55
Adjust the Image • Adjust the screw on the lamp side to move the image left or right. Base of projector FRONT driver image image Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
2. Set the breaker switch on the projector baseplate to the on position. 3. When the projector reaches standby, on the touch panel controller, tap Home > Power. For more details on the specified voltage range, see Power requirements on page 94. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Adjust lamp power 1. On the touch panel controller, tap Menu > Lamp > Lamp Power. 2. Use the slider or enter a value to adjust the lamp power. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Before adjusting LampLOC, make sure the following criteria is met: • Make sure the lamp is on and the douser (shutter) is open during adjustment. Christie recommends a 10-minute warm-up. • Perform the LampLOC procedure.
6600W (110%) Record new lamp information The lamp serial number is an alphanumeric, user-defined field. Christie recommends choosing a distinct and descriptive name for every individual lamp. 1. On the touch panel controller, tap Menu > Lamp > Change Lamp.
5. To select a blend setting, tap Edge Blending and tap the required blend. 6. To select a black level blend setting, tap Black Level Blending and tap the required black level blend. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
5. To add a second or third device, repeat steps 2 to 4. 6. Select the options you want to monitor. Options include lamp fault, lamp life, power, fan stall, and thermal sensors. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
The TPC is mounted on the rear of the projector and can be adjusted to improve the TPC viewing angle. A side USB port can be used to download log files and install software upgrades. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
• Configuration • Communications • General Lens Adjust the lens offset, focus and zoom motors. These controls can be adjusted by either tapping the desired directional arrow, or by entering a numerical value. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Page 64
85. • Backup—See Back up projector settings on page 67. • Restore—See Restore settings from a local backup profile on page 68. About Display legal information regarding software licensing and usage agreements. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Signal Display the status of the four available option card slots. System Display system hardware control settings, such as: projector hours, pitch/roll, lamp motor status, lens motor status, and built-in self test. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Page 66
Display the operating temperatures as reported by the internal thermal sensors. Versions Display the hardware and software versions for all electrical components, such as: main control board, backplane, image processor, formatter boards and option cards. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
1. On the touch panel controller, tap Admin > Backup. 2. To back up the settings, tap a backup file. 3. If required, enter or change the name. 4. Tap OK. A message indicates the backup was successful. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Import a file from an external device to restore settings 1. If importing settings using the touch panel controller (TPC), insert the USB flash drive containing the file into the USB port on the side of the TPC. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Page 69
2. On the TPC, tap Admin > Restore. 3. Tap Import. 4. From the Choose file to restore dialog, navigate to the location where the file is stored. 5. Tap the file to select it. 6. Tap Open. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
• Never operate the projector without all of its covers in place. Caution! Failure to comply with the following could result in minor or moderate injury. Only Christie accredited service technicians are permitted to open any enclosure on the projector and only if the AC power has been fully disconnected.
A clogged blower impeller or motor can reduce air flow and lead to overheating and lamp failure. 1. Shut down the projector. 2. Remove the three screws securing the rear side cover. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
The coolant color may fade over time, however this does not impact the ability of the coolant to exchange heat. Only use coolant recommended by Christie in this projector. The liquid cooling module (LCM) circulates coolant through the digital micromirror device (DMD) heat sinks.
Page 73
12. Check for leaks, especially for any hoses that were removed around the filler cap. 13. Check for proper flow from the liquid cooling module. For more details, see Maintenance shutdown on page 70. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Filtration Notice. Failure to comply with the following may result in property damage. Use only high efficiency Christie approved filters: light engine filter (five-pack)—P/N:003-001184-XX, liquid cooling radiator filter—P/N: 003-003082-XX, and LAD filter (three-pack)—P/B:03-001982-51P. Never operate the projector without the filter installed. The air filters in this product cannot be cleaned thoroughly enough for reuse and can lead to the contamination of optical components.
Christie recommendations. • Never twist or bend the quartz lamp body. Use the correct wattage lamp supplied by Christie. • Never attempt to remove the lamp when it is hot. The lamp is under extremely high pressure when hot and may explode.
2. Fold a microfiber cloth and wipe the remaining dust particles off the lamp with the smooth portion of the cloth that has no folds or creases. Do not apply finger pressure. Instead, use the tension in the folded cloth to remove the dust. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Remove fingerprints, smudges, or oil from the projection lens 1. Brush most of the dust off with a camelhair brush or use a dust-free blower. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Christie recommendations. • Never twist or bend the quartz lamp body. Use the correct wattage lamp supplied by Christie. • Never attempt to remove the lamp when it is hot. The lamp is under extremely high pressure when hot and may explode.
To calibrate the lens motors, on the touch panel controller, tap Lens > Calibrate Lens Motors. Reset the lens to home position To reset the lens to the default home position, on the touch panel controller, tap Lens > Reset to Home Position. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Troubleshooting This section provides information and procedures for resolving common projector issues. If a projector issue cannot be resolved, contact a Christie accredited service technician. Projector does not power on • Make sure that all three circuit breakers on the lamp power supply (LPS) are turned on.
Make sure both lens caps have been removed from the projection lens. • Make sure the lamp is on. • Make sure that all power connections are good. • Make sure the shutter is fully open. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
• The horizontal or vertical scan frequency of the input signal may be out of range for the projector. For more details, see Specification on page 86. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
This usually occurs when two independent sources are not locked together. Verify the setup of the sources. If the sources are locked together, contact Christie Technical Support for help. Touch panel controller or projector head...
Main > 3D Settings > Invert Left/Right Eye. Frame multiplication applied to incoming video signals when not required Frame multiplication is enabled when 3Dmode is on (auto). Disabling this setting prevents frame multiplication. Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Run the projector interrogator The interrogator captures diagnostic information Christie personnel uses to help diagnose and correct projector issues. If a projector issue cannot be resolved, Christie personnel may request an interrogator file from the projector. Log files are compressed into a standard zip file.
Specification This section provides detailed Mirage 4K35 specifications. Due to continuing research, specifications are subject to change without notice. Display Panel Resolution and refresh rate Pixel format (H x V square pixels) 4096 x 2160 Processing path 23.97 - 60Hz...
Specification White point Nominal white y = 0.351 ± 0.002 (full white, after calibration) x = 0.314 ± 0.002 Gamma Nominal 2.6 ± 5% Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
1 start bit, 8 data bits, 1 stop bit, no parity RS232 IN Connector 9-pin subminiature D, female Bit rate 115,200 bps Data format 1 start bit, 8 data bits, 1 stop bit, no parity Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
The projector shutdowns within one minute of an error threshold being reached. Location Warning Error Remarks (°C) (°C) Integrator rod Prism Air intake Lamp exhaust MCPU HIP scaler HIP warp red HIP warp green HIP warp blue Formatter red DMD red Formatter green Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Current rating of AC input 10-15 A maximum (specified wall breaker) Lamp (DC) Operating voltage range 18 - 46 VDC Start-up voltage (open current) 135-175 VDC Operating current range 50-180 A Connector type Field wireable lugs Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Projection Head AC Input Rated input voltage 200 - 240 VAC Rated line frequency 50 - 60 Hz nominal Inrush current 70 A maximum Current consumption 6 A maximum (at 200 VAC) Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Page 96
Lamp power supply power receptacle output Operating voltage range 200 - 230 VAC Operating current range—projection head Operating current range—heat extractor Current rating of input Both run from 15 A breaker (internal) Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
Projector head weight Without lens mount cover 114 kg (251 lbs) Shipping (includes packaging) 146 kg (322 lbs) Operating position Rotation about projection axis +90 degrees maximum (lamp door down), -15 degrees maximum Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)
EU Directive (2011/65/EU) on the restriction of the uses of certain hazardous substances (RoHS) in electrical and electronic equipment and the applicable official amendment(s) EU Regulation (EC) No. 1907/2006 onthe registration, evaluation, authorization and restriction of chemicals (REACH) and the applicable official amendment(s). Mirage 4K35 User Manual 020-101377-03 Rev. 1 (07-2015)